Napoleon Allure Vertical Series User manual

24 Napoleon Road, Barrie, Ontario, Canada L4M 0G8 • 214 Bayview Drive, Barrie, Ontario, Canada L4N 4Y8
Fireplaces, Heating and Cooling: 705-721-1212 • Grills: 705 726-4278 • napoleonproducts.com
ALLURE™ VERTICAL SERIES - NEFVC38H
W415-1907 / 09.20.18
Specifications
Dimensions
Product information provided is not complete and is subject to change without notice. Please consult the installation manual for
the most up to date installation information.
36 1/2”
(927.40mm)
13/16”
(19.60mm) 14”
(365.50mm)
1”
(24.95mm)
BACK VIEW
36 1/2”
(927.40mm)
6”
(153.20mm)
5/16”
(8.20mm)
26”
(660.20mm)
38”
(965.2mm)
151/4” (385mm)
16” (406.40mm)
5/8”
(15mm)
5/8”
(15mm)
RIGHT SIDE
VIEW FRONT VIEW
5 5/8”
(143.50mm)
Minimum Mantel Clearances
• When using paint or lacquer to finish the mantel, the paint or lacquer must be heat resistant to prevent discolouration.
!WARNING
Side View (Wall Mount)
0"
Mantel
Floor
Wall
Side View (recessed into a wall)
0"
0"
0"
Floor
0"
Mantel
* See “Recessed Installation” section for framing dimensions.
Model BTU Watts Width Height Depth Viewing Area
Actual Framing Actual Framing Actual Framing
NEFVC38H 5000 1500 16 * 38 * 5 5/8 * 26 x 15 1/4
3”
(76mm)
2”
(5cm)
2”
(5cm)

24 Napoleon Road, Barrie, Ontario, Canada L4M 0G8 • 214 Bayview Drive, Barrie, Ontario, Canada L4N 4Y8
Fireplaces, Heating and Cooling: 705-721-1212 • Grills: 705 726-4278 • napoleonproducts.com
Side View (recessed into a wall)
Brackets
B
A
W415-1907 / 09.20.18
ALLURE™ VERTICAL SERIES - NEFVC38H
Wall-Mount Installation
Recessed Installation
(NON-LOAD
BEARING)
note:
We recommend having 2 people install this appliance.
1. Remove front glass (see "front glass removal and installation"
section). If applicable, remove existing media.
2. Place appliance on a soft, non-abrasive surface then remove the
side covers secured to the back of the appliance. Set aside.
3. Remove the bottom bracket (FIG. 1). Set aside.
4. Hold the appliance against the wall to determine its final location.
5. Using the appropriate wall mounting installation template (see
manual), mark out the back and bottom bracket locations on the
wall.
6. Install the back bracket (shipped inside the styrofoam piece
protecting the top of the appliance) using 2 drywall anchors and 2
wood screws (supplied). Ensure the bracket is levelled.
7. Install the bottom bracket using 2 drywall anchors and 2 wood
screws (supplied).
8. Lift the appliance up until the two mounting slots clear the hooks
on the back bracket. Slide appliance down until completely
secured.
9. Secure the appliance to the bottom bracket using the screws
previously removed in Step 3 (FIG. 2).
10. Install the front glass (see “front glass removal and installation”
section).
11. Install the side covers using the 4 screws previously removed in
Step 2 (FIG. 3).
1. Remove the side covers secured to the back of the appliance and discard.
2. Insert the appliance into the recess, and then mark the top and bottom bracket locations. Remove
the appliance from the recess and set aside on a soft, non-abrasive surface.
3. Remove the top and bottom brackets (FIG. 1).
4. Using the top and bottom bracket location markings from Step 2, install the top and bottom
brackets to the wall using 4 wood screws (supplied).
5. Re-insert the appliance into the recess, and then secure it to the top and bottom brackets (FIG. 1).
Top Bracket
Bottom Bracket
FIG. 1
FINISHING MATERIAL
Measurements from body of appliance:
Sides, Back, Top 0”
note:
The mounting brackets should be screwed into the wall studs with at
least 2 screws. If the screws cannot be screwed into a stud, ensure
that plastic anchors (provided) are used to affix the brackets to the wall
and that the brackets are adequately secured.
note:
The hooks on the back bracket must be facing upwards.
FIG. 1
FIG. 2
Side Cover
FIG. 3
A B C
30 3/4" (78.1cm) 14 1/2" (36.8cm) 3 1/2” (8.9cm) min.
C