National Instruments IC-317 Series User manual

National Instruments IC-3173 Manual
Get Pricing & Availability at
ApexWaves.com
Call Today: 1-800-915-6216
Email: [e-mail]
https://www.apexwaves.com/modular-systems/national-instruments/industrial-controllers/IC-3173

USER MANUAL
IC-317x
Industrial Controller with Reconfigurable I/O
This document describes the features of the National Instruments IC-317x and contains
information about mounting and operating the device.
Contents
IC-3171, IC-3172, and IC-3173................................................................................................1
About the IC-317x............................................................................................................ 1
Hardware Overview.......................................................................................................... 2
Mounting the IC-317x.....................................................................................................21
IC-3173 (IP67)........................................................................................................................ 27
About the IC-3173 (IP67)............................................................................................... 27
Hardware Overview........................................................................................................ 28
Mounting the IC-3173 (IP67)......................................................................................... 45
Software Options.....................................................................................................................48
IEEE 1588 Precision Time Protocol References.....................................................................49
BIOS Configuration and System Recovery............................................................................ 49
Entering BIOS Setup.......................................................................................................49
BIOS Setup Utility Keyboard Navigation...................................................................... 49
Main Setup Menu............................................................................................................50
Advanced Menu.............................................................................................................. 51
Boot Menu.......................................................................................................................53
Save & Exit Menu...........................................................................................................54
Restoring the NI Linux Real-Time Operating System....................................................55
Restoring the Windows Operating System..................................................................... 55
Where to Go Next................................................................................................................... 57
Resources for LabVIEW Users.......................................................................................57
Resources for Vision Builder AI Users...........................................................................57
Worldwide Support and Services............................................................................................ 57
IC-3171, IC-3172, and IC-3173
The following information applies to the IC-3171, IC-3172, and IC-3173.
About the IC-317x
The IC-317x is a high-performance, small, fanless embedded computer designed for rugged
industrial applications. The IC-317x also provides multiple digital input/output (I/O) options
for communicating with external devices.

Figure 1. IC-317x Block Diagram
Intel Dual-Core Processor
i7-5650U, i5-5350U,
or Celeron 3765U
Xilinx
Kintex-7 FPGA
7K160T
IC-317x
Hardware
Data
x2 DisplayPort
8/4 GB DDR3L
Memory
64/32/4 GB
Solid-state Drive
RJ50 Serial Port
RS-232/422/485
x8 TTL I/O
x2 RS-422 I/O
x8 Isolated
Outputs
x8 Isolated
Inputs
RJ45 Primary Gigabit
Ethernet Port
x2 USB 3.0
Host Ports
x4 USB 2.0
Host Ports
x4 RJ45 Gigabit
Ethernet Ports with PoE
2 GB DDR3L
Memory
4.5 MB
QDR-II+ SRAM
PCI Express
Switch
44-pin D-sub
IC-3173 Only
PCIe
Gen 2
x4
PCIe
Gen 2
x4
Hardware Overview
The IC-317x front panel consists of four Gigabit Ethernet ports with Power over Ethernet
(PoE), one RS-232/RS-485 serial port, one standard Gigabit Ethernet Port, two USB 3.0 ports,
four USB 2.0 ports, and two DisplayPort connectors.
The IC-317x front panel also includes LEDs for communicating system status and a 44-pin
Digital I/O port. The Digital I/O port offers 8 isolated inputs, 8 isolated outputs, 2 bidirectional
differential I/O (RS-422) or single-ended input lines that can be used with a quadrature
encoder, and 8 bidirectional TTL lines.
2| ni.com | IC-317x User Manual

Figure 2. IC-317x Front Panel
POWER
PoE1
PoE2
PoE3
PoE4
DIO
STATUS
USER1
DP
DP
USER FPGA1
ACT/
LINK
10/10 0/
1000
17
4
14
5
6
7
1
12
13
9
10
11
16
15
8
2
3
1. DisplayPort Connectors
2. LED Indicators
3. Power over Ethernet (PoE) LED Indicators
4. Gigabit Ethernet Ports with PoE
5. 44-pin Digital I/O Connector
6. Isolated Power Input Connector
7. Chassis Grounding Screw
8. Reset Button (not pictured)
9. Power Button
10. System Power Connector
11. User-Accessible Battery Compartment (not
pictured)
12. RS-232/RS-485 Serial Port
13. USB 3.0 Ports
14. Primary Gigabit Ethernet Port
15. Retention Mounts for USB 3.0 Ports
16. Retention Mounts for USB 2.0 Ports
17. USB 2.0 Ports
Connector Pinouts
The IC-317x provides the following connectors.
DisplayPort
Use the DisplayPort connectors to connect one or more monitors to implement a local HMI for
your controller. You can develop a single real-time VI to use for both your user interface and
system logic. For more information, refer to the Using the Embedded UI to Access RT Target
IC-317x User Manual | © National Instruments | 3

VIs topic in the LabVIEW Help. For up-to-date information about supported NI cables and
accessories, refer to the pricing section of the product page at ni.com.
Use an appropriate adapter cable to connect a DisplayPort connector to a VGA or DVI
connector. The following figure lists the DisplayPort pins and signals.
Figure 3. DisplayPort Connector Pin Locations (IP20)
1
19 20
2
Table 1. DisplayPort Connector Pin Descriptions
Pin Signal Name
1 ML_Lane0(p)
2 GND
3 ML_Lane0(n)
4 ML_Lane1(p)
5 GND
6 ML_Lane1(n)
7 ML_Lane2(p)
8 GND
9 ML_Lane2(n)
10 ML_Lane3(p)
11 GND
12 ML_Lane3(n)
13 CONFIG1
14 CONFIG2
15 AUX CH (p)
16 GND
17 AUX CH (n)
18 Hot Plug Detect
4| ni.com | IC-317x User Manual

Table 1. DisplayPort Connector Pin Descriptions (Continued)
Pin Signal Name
19 Return
20 DP_PWR
Ethernet Ports
The IC-317x provides one standard Gigabit Ethernet network port and four Gigabit Ethernet
ports with Power over Ethernet (PoE). The Ethernet ports provide a connection between the
IC-317x, a network, and other Ethernet devices. The IC-317x automatically detects the speed
of the connection and configures itself accordingly.
If a PoE-capable device is plugged into an Ethernet port with PoE, the IC-317x automatically
supplies power to the device. When the IC-317x supplies PoE, the LED that corresponds to the
port illuminates. When you unplug a PoE device, PoE is automatically disabled. You can use
non-PoE Ethernet devices with PoE-enabled Gigabit Ethernet ports.
A CAT 5e or CAT 6 1000Base-T Ethernet cable is required to achieve 1,000 Mbps (Gigabit)
Ethernet performance. CAT 5 Ethernet cables are not guaranteed to meet the necessary
requirements. While CAT 5 cables may appear to work at 1,000 Mbps, CAT 5 cables can cause
bit errors, resulting in degraded or unreliable network performance.
(Windows only) The network Ethernet port provides Wake-on-LAN functionality from the
power off state when associated with the Intel® driver. Wake-on-LAN must be enabled in the
Power Management tab of the Intel I210 Gigabit Network Connection Properties dialog for the
primary Ethernet port in Device Manager. The NI GigE Vision driver (NI-GEV) does not
support Wake-on-LAN. The Ethernet ports with PoE do not support Wake-on-LAN.
Figure 4. Ethernet Port Pin Locations (IP20)
1
2
3
4
5
6
7
8
IC-317x User Manual | © National Instruments | 5

Table 2. Ethernet Port Pin Descriptions
Pin Fast Ethernet (100 Mbps) Gigabit Ethernet
MDI MDI-X
1 TX+ BI_DA+ BI_DB+
2 TX- BI_DA- BI_DB-
3 RX+ BI_DB+ BI_DA+
4 No Connect BI_DC+ BI_DD-
5 No Connect BI_DC- BI_DD-
6 RX- BI_DB- BI_DA-
7 No Connect BI_DD+ BI_DC+
8 No Connect BI_DD- BI_DC-
Digital I/O
The 44-pin Digital I/O port on the IC-317x offers 8 isolated inputs, 8 isolated outputs, 2
bidirectional differential inputs (RS-422) or single-ended input lines that can be used with a
quadrature encoder, and 8 bidirectional TTL lines. The Digital I/O port can be connected to
any appropriate shielded device or connector block using a shielded cable.
NI recommends the following digital I/O cables for the IC-317x.
Cable Part Number
44-pin D-sub male to pigtail cable 156083-03 for 3 meter cable
44-pin D-sub male to 44-position D-sub female cable 156084-03 for 3 meter cable
156084-0R5 for 0.5 meter cable
Refer to the following image and table for pin locations and descriptions.
Figure 5. 44-pin Digital I/O Connector Pin Locations (IP20)
15
30
44
1
16
31
6| ni.com | IC-317x User Manual

Table 3. Digital I/O Pin Descriptions
Pin Number Signal Description
1 Diff 0+ Bidirectional RS-422 I/O (positive side), or quadrature encoder
phase A+
2 GND Digital ground reference for TTL and differential I/O
3 TTL 0 Bidirectional TTL I/O
4 TTL 1 Bidirectional TTL I/O
5 GND Digital ground reference for TTL and differential I/O
6 TTL 2 Bidirectional TTL I/O
7 TTL 3 Bidirectional TTL I/O
8 GND Digital ground reference for TTL and differential I/O
9 Diff 1+ Bidirectional RS-422 I/O (positive side), or quadrature encoder
phase B+
10 VISO Isolated power voltage reference output
11 CISO Common ground reference for isolated inputs and outputs
12 Iso Out 0 General purpose isolated input
13 Iso Out 1 General purpose isolated input
14 CISO Common ground reference for isolated inputs and outputs
15 Iso Out 4 General purpose isolated output
16 Diff 0- Bidirectional RS-422 I/O (negative side), or quadrature encoder
phase A-
17 GND Digital ground reference for TTL and differential I/O
18 TTL 4 Bidirectional TTL I/O
19 TTL 5 Bidirectional TTL I/O
20 GND Digital ground reference for TTL and differential I/O
21 TTL 6 Bidirectional TTL I/O
22 TTL 7 Bidirectional TTL I/O
23 GND Digital ground reference for TTL and differential I/O
24 Diff 1- Bidirectional RS-422 I/O (negative side), or quadrature encoder
phase B-
25 VISO Isolated power voltage reference output
IC-317x User Manual | © National Instruments | 7

Table 3. Digital I/O Pin Descriptions (Continued)
Pin Number Signal Description
26 CISO Common ground reference for isolated inputs and outputs
27 Iso Out 2 General purpose isolated output
28 Iso Out 3 General purpose isolated output
29 CISO Common ground reference for isolated inputs and outputs
30 Iso Out 5 General purpose isolated output
31 Iso In 0 General purpose isolated input
32 iso In 1 General purpose isolated input
33 CISO Common ground reference for isolated inputs and outputs
34 Iso In 2 General purpose isolated input
35 Iso In 3 General purpose isolated input
36 CISO Common ground reference for isolated inputs and outputs
37 Iso In 4 General purpose isolated input
38 Iso In 5 General purpose isolated input
39 CISO Common ground reference for isolated inputs and outputs
40 Iso In 6 General purpose isolated input
41 Iso In 7 General purpose isolated input
42 CISO Common ground reference for isolated inputs and outputs
43 Iso Out 6 General purpose isolated output
44 Iso Out 7 General purpose isolated output
Wiring an Isolated Input
You can wire an isolated input to a sourcing output device.
8| ni.com | IC-317x User Manual

Caution Do not allow the voltage on the isolated inputs to exceed 30 VDC. Doing
so will damage the IC-317x.
Figure 6. Connecting an Isolated Input to a Sourcing Output Device
VREF
CISO
Industrial Controller
Input
Sourcing
Output
Device
Current
Limiter
Power Supply
+
–
Wiring an Isolated Output
The digital isolated output circuits source current to external loads.
When an inductive load, such as a relay or solenoid, is connected to an output, a large counter-
electromotive force may occur at switching time due to energy stored in the inductive load.
This flyback voltage can damage the outputs and the power supply.
To limit flyback voltages at the inductive load, install a flyback diode across the load. Mount
the flyback diode as close to the load as possible. Use this protection method if you connect
any of the isolated outputs on the IC-317x to an inductive load.
The following image shows an example of an isolated output wired to an external load with a
flyback diode installed across the load.
IC-317x User Manual | © National Instruments | 9