National Instruments NI 5734 User manual

NI-5734

NI 5731/5732/5733/5734R User Guide
and Specifications
The NI 5731/5732/5733/5734 is a family of high-speed digitizer adapter modules designed to work in
conjunction with your NI FlexRIOFPGA module. This document contains signal information and
specifications for the NI 5731/5732/5733/5734R, which is composed of an NI FlexRIO FPGA module
and the NI 5731/5732/5733/5734. This document also contains tutorial sections that demonstrate how
to acquire data using a LabVIEW FPGA example VI and how to create and run your own LabVIEW
project with the NI 5731/5732/5733/5734R.
Note NI 5731/5732/5733/5734R refers to the combination of your NI 5731/5732/5733/5734
adapter module and your NI FlexRIO FPGA module. NI 5731/5732/5733/5734 refers to your
NI 5731/5732/5733/5734 adapter module only.
A description of each of the NI 5731/5732/5733/5734 devices is given below:
•NI 5731—2 analog input, 12-bit, 40 MS/s digitizer
•NI 5732—2 analog input, 14-bit, 80 MS/s digitizer
•NI 5733—2 analog input, 16-bit, 120 MS/s digitizer
•NI 5734—4 analog input, 16-bit, 120 MS/s digitizer
Contents
Electromagnetic Compatibility Guidelines.......................................................................................... 2
How to Use Your NI FlexRIO Documentation Set ............................................................................. 3
Front Panel and Connector Pinouts ..................................................................................................... 4
Block Diagram..................................................................................................................................... 6
NI 5731/5732/5733/5734 Component-Level Intellectual Property (CLIP)......................................... 7
Cables................................................................................................................................................... 8
Clocking............................................................................................................................................... 9
Using Your Device with a LabVIEW FPGA Example VI .................................................................. 10
Creating a LabVIEW Project and Running a VI on an FPGA Target................................................. 12
Specifications....................................................................................................................................... 15
Where to Go for Support ..................................................................................................................... 41
Appendix: Installing EMI Controls ..................................................................................................... 42

NI 5731/5732/5733/5734R User Guide and Specifications 2 ni.com
Note Before configuring your NI 5731/5732/5733/5734R, you must install the appropriate software
and hardware. Refer to the NI FlexRIO FPGA Module Installation Guide and Specifications for
installation instructions. Figure 1 shows an example of a properly connected NI FlexRIO device.
Figure 1. NI FlexRIO Device
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits for electromagnetic
compatibility (EMC) as stated in the product specifications. These requirements and limits are designed
to provide reasonable protection against harmful interference when the product is operated in its
intended operational electromagnetic environment.
This product is intended for use in industrial locations. There is no guarantee that harmful interference
will not occur in a particular installation, when the product is connected to a test object, or if the product
is used in residential areas. To minimize the potential for the product to cause interference to radio and
television reception or to experience unacceptable performance degradation, install and use this product
in strict accordance with instructions in the product documentation.
Furthermore, any changes or modifications to the product not expressly approved by National
Instruments could void your authority to operate it under your local regulatory rules.
Caution To ensure the specified EMC performance, you must install PXI EMC Filler Panels
(National Instruments part number 778700-01) in adjacent chassis slots. For more information about
installing PXI EMC filler panels in your system, refer to the Appendix: Installing EMI Controls
section of this document.
Caution To ensure the specified EMC performance, operate this product only with shielded cables
and accessories.
Caution To ensure the specified EMC performance, install the included snap-on ferrite bead
(National Instruments part number 711856-01) on any cable attached to the AUX I/O connector in
accordance with the instructions listed in the Appendix: Installing EMI Controls section.
Caution This product is sensitive to electrostatic discharge (ESD). To ensure the specified EMC
performance, follow the programming instructions listed at the end of the Using Your Device with a
LabVIEW FPGA Example VI and Creating a LabVIEW Project and Running a VI on an FPGA
Target sections of this document.
NI FlexRIO
Adapter Module + = NI FlexRIO Device
NI FlexRIO
FPGA Module

©National Instruments Corporation 3 NI 5731/5732/5733/5734R User Guide and Specifications
How to Use Your NI FlexRIO Documentation Set
Refer to Figure 2 and Table 1 for information about how to use your NI FlexRIO documentation set.
Figure 2. How to Use Your NI FlexRIO Documentation Set
Table 1. NI FlexRIO Documentation Locations and Descriptions
Document Location Description
NI FlexRIO FPGA
Module Installation
Guide and Specifications*
Available in your FPGA module
hardware kit and from the Start Menu.
Contains installation instructions for your
NI FlexRIO system and specifications for your
FPGA module.
NI xxxxR User Guide and
Specifications*
Available from the Start Menu. Contains signal information, examples, and
specifications for your adapter module.
LabVIEW FPGA Module
Help*
Embedded in LabVIEW Help.Contains information about the basic functionality of
LabVIEW FPGA Module.
NI FlexRIO Help*Embedded in LabVIEW FPGA
Module Help.
Contains FPGA module, adapter module, and CLIP
configuration information.
LabVIEW Examples Available in NI Example Finder. Contains examples of how to run FPGA VIs and
Host VIs on your device.
Other Useful Information on ni.com
ni.com/ipnet Contains LabVIEW FPGA functions and intellectual property to share.
ni.com/flexrio Contains product information and data sheets for NI FlexRIO devices.
* These documents are also available at ni.com/manuals.
LabVIEW FPGA
Module Help
NI FlexRIO
Help
LabVIEW
Examples
INSTALL Hardware
and Software
CONNECT Signals
and Learn About
Your Adapter
Module
LEARN About
LabVIEW FPGA
Module
PROGRAM Your
NI FlexRIO System
in LabVIEW FPGA
Module
NI FlexRIO FPGA Module
Installation Guide and Specifications
NI FlexRIO Adapter Module
User Guide and Specifications
Are
You New to
LabVIEW FPGA
Module?
Ye s N o
No

NI 5731/5732/5733/5734R User Guide and Specifications 4 ni.com
Front Panel and Connector Pinouts
Front Panel
Table 2 shows the front panel connector and signal descriptions for the NI 5731/5732/5733/5734. Refer
to the Specifications section of this document for additional signal information.
Table 2. NI 5731/5732/5733/5734 Front Panel Connectors
Connector Signal Description
AI 0 50 single-ended analog input channel 0.
AI 1 50 single-ended analog input channel 1.
AI 2 50 single-ended analog input channel 2 (NI 5734 only).
AI 3 50 single-ended analog input channel 3 (NI 5734 only).
CLK IN Reference or external clock input, 50 single-ended.
AUX I/O Refer to Table 3 for the signal list and descriptions.
AUX
I/O
AI 0
CLK IN
AI 1
NI 5732
INSTRUMENTS
NATIONAL
80 MS/s
Digitizer
AUX
I/O
AI 0
CLK IN
AI 1
NI 5731
INSTRUMENTS
NATIONAL
40 MS/s
Digitizer
AUX
I/O
AI 0
CLK IN
AI 1
NI 5733
INSTRUMENTS
NATIONAL
120 MS/s
Digitizer
AUX
I/O
AI 0
CLK IN
AI 1
AI 3
AI 2
NI 5734
INSTRUMENTS
NATIONAL
120 MS/s
Digitizer

©National Instruments Corporation 5 NI 5731/5732/5733/5734R User Guide and Specifications
Caution Connections that exceed any of the maximum ratings of any connector on the
NI 5731/5732/5733/5734 can damage the device and the chassis. NI is not liable for any damage
resulting from such signal connections. For the maximum input and output ratings for each signal,
refer to the Specifications section of this document.
AUX I/O Connector
Table 3 shows the pin assignments for the AUX I/O connector on the NI 5731/5732/5733/5734.
Caution The AUX I/O connector accepts a standard, third-party HDMI cable, but the AUX I/O port
is not an HDMI interface. Do not connect the AUX I/O port on the NI 5731/5732/5733/5734 into the
HDMI port of another device. NI is not liable for any damage resulting from such signal connections.
Table 3. NI 5731/5732/5733/5734 AUX I/O Connector Pin Assignments
AUX I/O Connector Pin Signal Signal Description
1 DIO Port 0 (0) Bidirectional single-ended digital I/O data channel.
2 GND Ground reference for signals.
3 DIO Port 0 (1) Bidirectional single-ended digital I/O data channel.
4 DIO Port 0 (2) Bidirectional single-ended digital I/O data channel.
5 GND Ground reference for signals.
6 DIO Port 0 (3) Bidirectional single-ended digital I/O data channel.
7 DIO Port 1 (0) Bidirectional single-ended digital I/O data channel.
8 GND Ground reference for signals.
9 DIO Port 1 (1) Bidirectional single-ended digital I/O data channel.
10 DIO Port 1 (2) Bidirectional single-ended digital I/O data channel.
11 GND Ground reference for signals.
12 DIO Port 1 (3) Bidirectional single-ended digital I/O data channel.
13 PFI 0 Bidirectional single-ended digital I/O data channel.
14 NC No connect.
15 PFI 1 Bidirectional single-ended digital I/O data channel.
16 PFI 2 Bidirectional single-ended digital I/O data channel.
17 GND Ground reference for signals.
18 +5V +5 V power (10 mA maximum).
19 PFI 3 Bidirectional single-ended digital I/O data channel.
2
4
6
8
10
12
14
16
18
1
3
19
17
15
13
11
9
7
5

NI 5731/5732/5733/5734R User Guide and Specifications 6 ni.com
Block Diagram
Figure 3 shows the NI 5731/5732/5733/5734 block diagram and signal flow to and from the
NI 5731/5732/5733/5734 component-level intellectual property (CLIP) by way of the adapter module
and the corresponding CLIP in LabVIEW FPGA.
Figure 3. NI 5731/5732/5733/5734 Connector Signals and CLIP Signal Block Diagram
NI 5731/5732/5733/5734 Adapter Module
AI 0
AI 2
DIO Port 0 (0)
DIO Port 0 (1)
DIO Port 0 (2)
DIO Port 0 (3)
DIO Port 1 (0)
DIO Port 1 (1)
DIO Port 1 (2)
DIO Port 1 (3)
PFI 0
PFI 1
PFI 2
PFI 3
AUX I/O
ADC
ADC Clock
ADC Data
Sample Clock
ADC
LabVIEW FPGA CLIP
ADC Clock
ADC Data
ADC
Interface
ADC
Interface
AI 0
AI 2
AI 0 Over Range
AI 2 Over Range
16
DC Over Voltage
4
SPI Device Select
SPI Read
SPI Write
SPI Write Data
SPI Address
SPI Idle
32
32
DIO Port 0 WE
DIO Port 0 Rd Data (0)
DIO Port 0 Wr Data (0)
DIO Port 0 Rd Data (1)
DIO Port 0 Wr Data (1)
DIO Port 0 Rd Data (2)
DIO Port 0 Wr Data (2)
DIO Port 0 Rd Data (3)
DIO Port 0 Wr Data (3)
DIO Port 1 Rd Data (0)
DIO Port 1 Wr Data (0)
DIO Port 1 Rd Data (1)
DIO Port 1 Wr Data (1)
DIO Port 1 Rd Data (2)
DIO Port 1 Wr Data (2)
DIO Port 1 Rd Data (3)
DIO Port 1 Wr Data (3)
DIO Port 1 WE
PFI 3 Wr Data
PFI <0..3> WE
PFI 3 Rd Data
PFI 1 Rd Data
PFI 1 Wr Data
PFI 2 Rd Data
PFI 2 Wr Data
PFI 0 Rd Data
PFI 0 Wr Data
4
User Data 1
User Command
User Command Commit
User Command Status
User Return
Initialization Done
User Error
User Command Idle
User Data 0
AI 1
AI 3
SPI Read Data
PLL Locked
Sync Clock
CLK IN
SPI Engine
Calibration
EEPROM
DAC SPI
ADC SPI
ADC SPI
ADT7408
Temperature
Sensor
DAC
OUT1 OUT2
CP
OUT4
CLK1
REF IN
AD9511
CLK2
SPI
VCXO
AC/DC
Gain
1, 2, 4x
Filters
AC/DC
Gain
1, 2, 4x
Filters
PLL Loop
Filter
Enable VCXO
Enable PLL
External Sample CLK
External Ref CLK
Channel Controls
Microcontroller
AI 1
AI 3
AI 1 Over Range
AI 3 Over Range
16
16
16

©National Instruments Corporation 7 NI 5731/5732/5733/5734R User Guide and Specifications
NI 5731/5732/5733/5734 Component-Level Intellectual Property (CLIP)
The LabVIEW FPGA Module includes a feature for HDL IP integration called CLIP. NI FlexRIO
devices support two types of CLIP: user-defined and socketed.
•User-defined CLIP allows users to insert HDL IP into an FPGA target, enabling VHDL code to
communicate directly with an FPGA VI.
•Socketed CLIP provides the same IP integration functionality of the user-defined CLIP, but also
allows the CLIP to communicate directly with circuitry external to the FPGA. Adapter module
socketed CLIP allows your IP to communicate directly with both the FPGA VI and the external
adapter module connector interface.
Figure 4 shows the relationship between an FPGA VI and CLIP.
Figure 4. CLIP and FPGA VI Relationship
Adapter Module
CLIP Socket
LabVIEW
FPGA VI
User-Defined
CLIP
NI FlexRIO FPGA Module
FPGA
External
I/O Connector
Adapter
Module
Socketed
CLIP
User-Defined
CLIP Fixed I/O
DRAM 0
CLIP Socket
Socketed
CLIP
DRAM 1
CLIP Socket
Socketed
CLIP
Fixed I/O
Fixed I/O
DRAM0 DRAM1

NI 5731/5732/5733/5734R User Guide and Specifications 8 ni.com
The NI 5731/5732/5733/5734 ships with socketed CLIP items that are used to add module I/O to the
LabVIEW project.
The NI 5731/5732/5733/5734 CLIP items provides access to two analog input channels (four analog
input channels on the NI 5734), eight bidirectional DIO channels, four bidirectional PFI channels, and
an input clock selector that can be configured to use one of the following settings:
• Internal Sample clock
• Internal Sample clock locked to an external Reference clock through the CLK IN connector
• External Sample clock through the CLK IN connector
• Internal Sample clock locked to an external Reference clock through Sync Clock
The CLIP items also contain an engine to program the ADC and clock, either through predetermined
settings for an easier instrument setup or through a raw SPI address and data signals for a more advanced
setup. In the LabVIEW FPGA Module, analog input data is accessed using a U16 data type (left
justified). The DIO signals are grouped into two ports of four signals each and are accessed using a U8
data type and Boolean write enable signal. The four PFI signals are accessed individually using
Booleans.
Refer to the NI FlexRIO Help for more information about NI FlexRIO CLIP items, configuring the
NI 5731/5732/5733/5734 with a socketed CLIP, and a list of available socketed CLIP signals.
Cables
• Use any shielded 50 coaxial cable of less than 3 meters in length with a BNC plug end to connect
to the AI 0, AI 1, AI 2, and AI 3 connectors on the NI 5731/5732/5733/5734 front panel.
• Use any shielded 50 coaxial cable of less than 3 meters in length with an SMB plug end to
connect to the CLK IN connector.
• Use any HDMI cable with the provided ferrite bead to connect to the digital I/O and PFI signals on
the AUX I/O connector.
Caution To ensure the specified EMC performance, install the included snap-on ferrite bead
(National Instruments part number 711856-01) on any cable attached to the AUX I/O connector in
accordance with the instructions listed in the Appendix: Installing EMI Controls section.

©National Instruments Corporation 9 NI 5731/5732/5733/5734R User Guide and Specifications
Clocking
The NI 5731/5732/5733/5734 clocks control the sample rate and other timing functions on the device.
Table 4 contains information about the possible NI 5731/5732/5733/5734 clock resources.
Note Specifications for the NI 5731/5732/5733/5734 adapter modules were characterized only at
the maximum sample rates.
Note For more information about configuring clocks, refer to the respective CLIP Help section for
your device in the NI FlexRIO Help.
Table 4. NI 5731/5732/5733/5734 Clock Sources
Clock
Configuration
Supported Sample
Rates
External
Clock
Type
External Clock
Frequency Description
Internal Clock
PLL Off
NI 5731 = 40 MS/s
NI 5732 = 80 MS/s
NI 5733 = 120 MS/s
NI 5734 = 120 MS/s
— — The internal VCXO
acts as a free-running
clock.
Internal Clock
PLL On
(IoModSyncClk)
NI 5731 = 40 MS/s
NI 5732 = 80 MS/s
NI 5733 = 120 MS/s
NI 5734 = 120 MS/s
—10 MHz The internal VCXO
locks to
IoModSyncClk (Sync
Clock), which is
provided only through
the backplane of
supported devices.
Internal Clock
PLL On
(CLK IN)
NI 5731 = 40 MS/s
NI 5732 = 80 MS/s
NI 5733 = 120 MS/s
NI 5734 = 120 MS/s
Reference
clock
10 MHz The internal VCXO
locks to an external
Reference clock,
which is provided
through the CLK IN
front panel connector.
External Clock
(CLK IN)
The supported
sample rate is equal
to the external clock
frequency.
Sample
clock
NI 5731 Min = 3 MHz
NI 5731 Max = 40 MHz
NI 5732 Min = 20 MHz*
NI 5732 Min = 10 MHz†
NI 5732 Max = 80 MHz
NI 5733 Min = 50 MHz
NI 5733 Max = 120 MHz
NI 5734 Min = 50 MHz
NI 5734 Max = 120 MHz
An external Sample
clock can be provided
through the CLK IN
front panel connector.
* Duty Cycle Stabilizer (DCS) enabled. DCS enabled is the default setting for all NI 5731/5732/5733/5734 CLIP items. You
can disable the DCS by adjusting register 9 in the ADC.
† DCS disabled.