Nauticam 21230 User manual

Current as of 2021-06-29
Instruction Manual for
Extension Ring 30/35/40/50/70 with
Focus knob
PN# 21230/21235/21240/21250/21270
F
ORE ORD
Thank you for your purchase of a NAUTICAM pro uct.
At NAUTICAM, we pri e ourselves in the ability to recognize the
requirements of professional as well as amateur un erwater
photographers an fulfill them through the innovative esigns of
our pro ucts. We strive to achieve a high level of user-
frien liness by allowing stress-free installation an easy operation
of all important functions of the camera.
Please rea this manual carefully before using the pro uct, this
will maximize its performance as well as its lifetime.
ARRANTY
All NAUTICAM Pro ucts are warrante against any material an
manufacturing efects for two years from the ate of purchase for
consumer use. This warranty only applies to pro ucts purchase
from authorize NAUTICAM ealers an oes not exten beyon
the original retail purchaser.
To return your pro uct for service, please contact your regional
authorize service center(s). Please note that this warranty only
applies when the pro uct is purchase in the territory where the
service center is locate .
NAUTICAM oes not hol responsibility for amage, of any nature,
to any equipment use with an /or place within our pro ucts.
NAUTICAM accepts no liability for any loss of capture images or
the inability to capture images even if it is ue to the
malfunctioning of our pro ucts.
Unauthorize mo ifications an /or repairs of our pro ucts will
automatically invali ate the warranty.
Please follow the instructions below to mount the Extension Ring
on a port.
M
OUNT ON THE
P
ORT
1.
Confirm that the Extension Ring 30
/70
is
unlocke , with the locking lever pointing
upwar s as shown.
2.
Align the "I" mark on the extension ring
with the WHITE ot on the port.
Gently push the extension ring towar s the
port until it cannot go any further.
2
3.
Turn the extension ring clockwise until the
white ot on the extension ring aligns with
the white ot on the port.
4.
Push the locking evice inwar s. Ensure
that the extension ring is securely locke
with the port
To unlock, release the locking evice an
reverse the above proce ures.

Current as of 2021-06-29
Remark: Nauticam supports only e-manuals. Please download
corresponding product manuals on Nauticam.com website, or
contact us for e-manuals.
M
OUNT THE PORT TO THE HOUSING
P
RE
-
CAUTIONS
Compatibility:
This extension ring is backwar s compatible with
other N120 extension rings. A user installable
locking tab is pre-installe for this purpose.
Remove the locking tab when using large
iameter lenses, such as Canon 11-24mm lens.
Locking tab
1.
Pull the co
ntrol
knob outwar s an m
ake
sure the control knob is at its most
outwar s position before moun ing/un-
mounting the port. The knob shoul be
left at this position until it is ma e sure
that the lens an focus gear is properly
installe .
2.
Engage the gear
by pushing in the knob,
then turn the knob both ways to check if
the lens focuses.
· After installation of the port combo, please make sure the
o-ring (s) are free from ebris an uneven surface issues.
· A water-tight test without the camera insi e the housing
is highly recommen e after the changing of port an O-
ring(s).
· Do not use lubricants from other bran s with the silicone
rubber O-ring on this housing, only use the lubricant
provi e by NAUTICAM.
· Discontinue use imme iately shoul you notice any
leakage.
· Do not open the pro uct in a wet or san y environment.
Protect the interior from moisture an ebris in or er to
prevent malfunction or leakage.
· Defective pro ucts shoul be shippe to our istributors
for service, unauthorize isassembling an /or
mo ifications coul result in malfunction or leakage.
3