Nauticam NA - Z7II User manual

NA - Z7II
For Nikon Z6 II/Z7 II Camera
User Manual
Housing
FF- MIL
Introduction 2
2
3
4
7
8
Package Contents
Important Instructions
Part Names and Functions
Opening the housing
Closing the housing
9
14
Preparation for Use
Recommended Accessories
PN 17227
15
16
17
Care/Storage
Warranty
Specifications

2
INTRODUCTION
PACKAGE CONTENTS
Thank you for purchasing this Nauticam product.
Before using the product, please read this manual thoroughly to familiarize yourself with full scope of functions on the
product as well as ensuring that you will use the product correctly.
Make sure that you have all the included items listed below before using this product.
If some items are missing or damaged, contact your local Nauticam dealer.
After purchase, we suggest that
you reuse all packaging materials
for future travelling.
Panasonic CR2032 Battery
(pre-installed for Moisture Alarm)
Spare Main O-ring
Padded Travel Case Allen key set
O-ring Remover Manual Instruction Card
NA-Z7II
(2 x Handles with Mounting Balls, 1 x Housing Cap,
2 x Optical Fiber Mount Caps, 2 x Stainless Steel Handle Brackets)
Lubricant

3
IMPORTANT INSTRUCTIONS
Water-tight test of the housing (without
camera inside) before usage is recom-
mended as well as any O-ring renewal
and port change.
Use only Nauticam lubricant on silicone
rubber O-ring.
Discontinue use immediately when there is
a sign of leakage.
Do not expose the housing in direct
sunlight for a prolonged period.
Prevent any sand or dust or water
penetration inside the housing. Be
extra careful when changing lens and
inserting or removing the camera.
This product is not intened for use by
children, or persons with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they
are supervised and/or given instruction by
a responsible person concerning use of
the product to ensure that they can use it
safely.
Do not seal the housing when travelling by
air as this may lead to a pressure difference
between the atmosphere and inside the
housing.
Only the accesories specified by
Nauticam must be used. Third-party
accessories may result in malfunctions
or damage to the product.
Do not stretch any O-rings excessively.
Only remove it using Nauticam O-ring
remover.
Do not open the housing in wet or sandy
environment. Protect the housing from
moisture and debris in order to prevent
malfunction or leakage.
1
3
5
7
9
11 12
4
6
8
10
2
Do not attempt to remove parts of the
housing yourself. Repairs must be done
at authorized service centers only.
The housing should be positioned on the a
stable and safe surface on land.

4
PART NAMES AND FUNCTIONS
Monitor mode lever Housing Lock
Housing unlock button Still / Movie button
Multi selector
Release mode button
Zoom in button
Delete button
button
i
Menu button
Moisture alarm window
Zoom out button
AE-L / AF-L button
1 2
3 4
5
7
9
11
13
6
8
10
12
Rear View
1
10
2
3
12
139 11
5
4
6
8
7
A
Multi selector - centerA

5
PART NAMES AND FUNCTIONS
M28 Accessory port
Exposure compensation button
Accessory mounting ball
Z lens release button
Optical cable connector
M14 Accessory port
Port lock safety button
F lens release button
Mode dial
M16 Accessory port
Port locking lever
Main Switch
Main command dial
Port index mark
1
5
9
13
2
6
10
14
3
7
11
4
8
12
Top + Front Views
1
3
2
5
4
6
7
8
12
13
14
9
10
11

6
PART NAMES AND FUNCTIONS
Back + Side Views
Playback lever
Fn 2 lever
Shutter release lever
Movie record lever
1/4” Threaded tripod holes
Zoom/Focus knob
AF-ON lever
ISO lever
Front dial
Display lever
Zinc Anodes
Fn 1 lever
3
7
9
11
1
4
8
10
12
5
2
6
2
10
9
11
8
12
1
4
6
7
3
5

7
OPENING THE HOUSING
depress housing unlock button
turn housing lock outward
lift up the back housing
*
drawings as illustrations onl
y
1
2
3

8
CLOSING THE HOUSING
Housing Lock - Lock
before closing the housing, clean
and lubricate the main O-ring
make sure nothing is caught
between front and back housing
and that they are fully aligned
before locking
turn housing lock inward until you
hear and feel it click into place
housing locked in place securely
1
2
3
*
drawings as illustrations onl
y

9
PREPARATION FOR USE
Installing the Camera - housing tray attachment & Z-mount / F-mount lens installment
*
drawings as illustrations onl
y
3
1
4
Z-mount / F-mount lens installent
2
5
unlock camera tray lever and remove the
tray from the housing
*please refer to page 10 for lens installment
before sliding in the camera
slide the camera tray back into the housing
along the tray rail
attach the camera tray by tightening the tray
screw into the tripod socket of the camera
lock camera tray
*place the zoom/focus knob in place and
make sure it is engaged with lens gear
Z-mount lens F-mount lens (w/ FTZ adaptor)
make sure the small lever is in vertical
position before Z mount lens installment
make sure the small lever is in horizontal
position before F mount lens installment

10
PREPARATION FOR USE
Port Mounting
depress safety button and rotate
anti-clockwise
lubricant the port O-ring before
mounting
align index mark
push port assembly straight in
rotate locking lever clockwise to
lock
1
2
3
*
drawings as illustrations onl
y

11
PREPARATION FOR USE
Coating housing O-ring
Main O-ring
remove the main O-ring using an O-ring remover
clean the O-ring groove with a cloth and ensure
that it is free from salt or other foreign materials
lightly coat it with provided lubricant
return the main O-ring by slowly pressing from
one corner to the whole perimeter
1
2
3
4
*
drawings as illustrations onl
y

12
PREPARATION FOR USE
Setting up moisture alarm
Alarm ON/OFF
CR2032
Battery
1
3
2
4
remove battery
insulation film
switch on the alarm
- the moisture alarm
window will flash in
BLUE when it is working
correctly
test the alarm
- connect the wires with a
dampened cotton bud; the
alarm will give a repeating
‘beep’ and the mositure alarm
window will flash RED
press the battery down until it
click into place
*
drawings as illustrations onl
y

13
PREPARATION FOR USE
Changing lens/port without opening the housing
1
4
2
3
If using with vacuum valve :
remove the cap from the vacuum
valve and press the red button to
release pressure before unlocking
port lock
If using without vacuum valve,
please follow from step 2
unlock port lock and remove port
assembly
press the blue button to reset
vacuum alarm before replacing
port
reset vacuum valve system using
hand pump then close the cap
*please refer to page 15 on complete vacuum system guidance
*
drawings as illustrations onl
y

14
RECOMMENDED ACCESSORY
Vacuum valve system
remove the plug of M16 accessory
port from the housing
remove the cap from the vacuum
valve
slightly lubricate the o-ring and
make sure the o-ring is in place
then tighten the vacuum valve to
the housing with the tool provided
connect hand pump to the valve
and pump several times until it
reaches the target vacuum level
close vacuum valve cap
* It is recommended to leave the housing
for at least 20mins to ensure it is sealed.
If the LED light changes from steady
green light to rapidly flashing yellow light,
that means there is a leakage. Please
check every O-ring and then conduct the
vacuum test again.
hand pump
moisture alarm
window
accesory port
on housing
vacuum valve
1
2
Moisture alarm window colour indication :
Steady Blue
Flashing Blue
Steady Green
Steady Red
Flashing Yellow
Flashing Red
Alternating
Blue and Red
device is turned on
standby mode,
ready for pumpng
target vacuum level
is reached
out of battery
vacuum level
is dropping
vacuum is totally lost,
circuit stalled untill
device is switched off
vacuum is totally lost,
circuit stalled untill
device is switched off
*
drawings as illustrations onl
y

15
CARE/STORAGE
Soak the housing system in fresh water
after salt water usage
Protect the housing with robust and
shock-proof travel case during trans-
portation. Do not travel with camera
inside housing.
Operate all controls and buttons at
least 3 times while immersed in fresh
water
We recommand cleaning and inspecting
the main O-ring each time after diving for
any damage and every time the housing
is opened.
We recommand to ship the housing to our
servic centers for a complete overhual
after 200 dives/every 2 years.
1
3
5
4
2

16
WARRANTY
All NAUTICAM Housing Products and Viewfinders are
warranted against any material and manufacturing
defects for two years from the date of purchase for
consumer use. NAUTICAM Optical Accessories are
warranted against material and manufacturing defects
for a period of one year, and HDMI cables carry a year
warranty.
This warranty only applies to products purchased from
authorized NAUTICAM dealers and does not extend be-
yond the original retail purchaser.
To return your product for service, please contact your
regional authorized service center(s). Please note that
this warranty only applies when the product is pur-
chased in the territory where the service center is lo-
cated.
NAUTICAM accepts no liability for any damage to and
defects in the housing caused by improper use and/or
poor maintenance; it is the responsibility of the own-
er to carefully follow the instructions in our manuals.
NAUTICAM does not hold responsibility for damage, of
any nature, to any equipment used with and/or placed
within our products.
NAUTICAM accepts no liability for any loss of captured
images or the inability to capture images even if it is
due to the malfunctioning of our products.
Unauthorized modifications and/or repairs of our
products will automatically invalidate the warranty.

17
SPECIFICATIONS
Construction
Dimensions
Monitor options ( 2.0 )
Wet Lens Compatibility
Weight
Depth
Port specifications
HDMI connectivity required accessories ( 2.0 )
HDMI connectivity required accessories ( 1.4 )
Housing body
Width
17922 Nauticam Atomos Ninja V Housing for Atomos Ninja V 5” (excl. HDMI 2.0 cable)
Macro
Macro to Wideangle
Wideangle
81201
81202
85204
86201
87301
85201
Super Macro Convertor 1
(SMC-1, 2.3x magnification)
Super Macro Convertor 2
(SMC-2, 4.0x magnification)
Macro to Wide Angle Lens 1
(MWL-1)
EMWL Set#1 (incl. focusing unit #1,
150mm relay lens & 3 objective lenses)
0.36x Wide Angle Conversion Port
with Aluminium Float Collar (incl.
N120 to N100 port adaptor)
In air
Rating
Port mount
25085 M28C1R200-M28A1R170 HDMI 2.0 Cable
25033 Standard HDMI Bulkhead with M16 Thread
Display window
Height
In water
Depth
Port accessories
25089 M28 Adaptor for HDMI 2.0 Cable
25080 M28-M16 Step Down Adaptor
25036 HDMI (D-C) cable in 190mm length
Hard Anodized Aluminium Alloy
360 mm
3.10 kg
100 m
N 120 Port System
Abrasion Resistant Polycarbonate
200 mm
-0.07 kg (w/ camera & battery)
160 mm
1 x M28, 1 x M16, 1 x M14
0.57x Wide Angle Conversion Port 2
with Aluminium Float Collar
(compatible with 14mm lenses)
Monitor options ( 1.4 )
17923 NA-Shinobi-H Housing for Atomos Shinobi 5.2” 4K HDMI Monitor
17906 NA-502H Housing for SmallHD 502 5” HD Monitor
* 25033 & 25036 are included in monitor housing packaging
Recommended accessories
Recommended wet lens accessories
17920 NA-502B-H Housing for SmallHD 502 Bright Monitor
25625 M16 Vacuum Valve II (pushbutton release)
25101 M67 flip diopter holder for M67 macro ports
87512 Shade for 130° Objective Lens
32201 180⁰Straight Viewfinder
25108 M67 Double Flip Holder for M67 Macro Ports
87518 Strobe Mounting Brackets for EMWL Relay Lens
87517 EMWL Bayonet Holder for Ø90 Float Arm
32203 45⁰Viewfinder
83213 M67 to Bayonet Mount Converter II
26308 TTL Flash Trigger for Nikon
83214 Bayonet Mount Adaptor for SMC/CMC
26216 Universal Optical Fiber Cable
87501 Flip Holder for EMWL

Nauticam Internationl Ltd.
Rm 2203, CCT Telecom Bldg,
11 Wo Shing St,
Fo Tan,
Hong Kong
Tel. +852 - 26902711
Fax. +852 - 26909778
URL. www.nauticam.com
Gallery. www.nauticam.smugmug.com