NCR SelfServ 84 Walk-Up User manual

NCRSelfServ™84Walk‐UpStandard Collar ATMSitePreparation
B006‐7519‐G000

B006‐7519‐G000
NCRSelfServ™84Walk‐UpATMSitePreparation
TheproductdescribedinthisdocumentisalicensedproductofNCR
Corporation.
NCRandNCRSelfServaretrademarksofNCRCorporation.Otherproduct
namesmentionedinthispublicationmaybetrademarksorregistered
trademarksoftheirrespectivecompaniesandareherebyacknowledged.
Wherecreationofderivativeworks,modificationsorcopiesofthisNCR
copyrighteddocumentationispermittedunderthetermsandconditionsofan
agreementyouhavewithNCR,NCR'scopyrightnoticemustbeincluded.
ItisthepolicyofNCRCorporation(NCR)toimproveproductsasnew
technology,components,software,andfirmwarebecomeavailable.NCR,
therefore,reservestherighttochangespecificationswithoutpriornotice.
Allfeatures,functions,andoperationsdescribedhereinmaynotbemarketed
byNCRinallpartsoftheworld.Insomeinstances,photographsareof
equipmentprototypes.Therefore,beforeusingthisdocument,consultwith
yourNCRrepresentativeorNCRofficeforinformationthatisapplicableand
current.
NCRProprietaryInformation‐nottobedisclosedorreproducedwithout
writtenconsent.
©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.
AllRightsReserved

NCRSelfServ™84Walk‐UpATMSitePreparation
i
NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
Contents
Introduction
Audience...............................................................................................1‐1
AboutThisDocument ...........................................................................1‐1
RevisionRecord ....................................................................................1‐1
CustomerResponsibilities
Notice ...................................................................................................2‐1
SiteCompliance ....................................................................................2‐1
CustomerActions .................................................................................2‐1
StandardsCompliance
RadioFrequencyInterference ..............................................................3‐1
FCCRadioFrequencyInterferenceStatement ................................3‐1
CanadianClassADeviceDeclaration...............................................3‐1
Safety ....................................................................................................3‐1
SafetyDirective................................................................................3‐1
HarmonisedSafetyStandard...........................................................3‐1
ElectromagneticCompatibility(EMC)...................................................3‐1
ImmunityStandards ........................................................................3‐1
EMCDirectives.................................................................................3‐1
EmissionStandards..........................................................................3‐1
AdditionalRequirementsfor220V‐240VUnits .............................3‐1
Accessibility ..........................................................................................3‐1
ProductOverview
GeneralDescription ..............................................................................4‐1
Options ............................................................................................4‐1
Acoustics...............................................................................................4‐1
HeatDissipation....................................................................................4‐1
ProductIdentification...........................................................................4‐1
SiteRequirements
PositioningtheATM .............................................................................5‐1
Floor......................................................................................................5‐1
DoorwaysandCorridors .......................................................................5‐1
Wall.......................................................................................................5‐1
WallCavity.......................................................................................5‐1
InstallingThroughaGlassWall........................................................5‐1
CollarTolerance...............................................................................5‐1
AmbientLighting...................................................................................5‐1
TaskLighting .........................................................................................5‐1
TemperatureandHumidity ..................................................................5‐2
NormalOperatingRange(InteriorEnvironment)............................5‐2
NormalOperatingRange(ExteriorEnvironment) ...........................5‐2
StorageRange(UpToThreeMonths) .............................................5‐2
TransitRange(UpToOneWeek) ....................................................5‐2
ExtremePowerOnRange(UpToOneHour) ..................................5‐2
BarometricPressure ............................................................................. 5‐2
PowerRequirements
ACPowerRequirements....................................................................... 6‐1
InputVoltageSetting............................................................................ 6‐1
Grounding............................................................................................. 6‐1
TransientProtection............................................................................. 6‐1
CableRequirements
CablePreparation................................................................................. 7‐1
DataLineTransientProtection.............................................................7‐1
AlarmInterfaceCables ......................................................................... 7‐1
BasicAlarmCable ............................................................................ 7‐1
EnhancedAlarmCable .................................................................... 7‐1
RemoteStatusMonitor ........................................................................ 7‐2
ShorteningtheCable....................................................................... 7‐2
RemoteRelayCable.............................................................................. 7‐2
EthernetStandardCable ......................................................................7‐2
PowerCable.......................................................................................... 7‐2
Decals
AdvertWindow .................................................................................... 8‐1
AdvertCollarorOpenAdvertCollar................................................8‐1
Entry/ExitDecals ..................................................................................8‐1
VariantDetails‐CENI,StandardCollarATM
PackageDimensions ............................................................................. 9‐1
ATMDimensions................................................................................... 9‐1
WeightandFloorLoading .................................................................... 9‐1
StandardSecurityEnclosures ..........................................................9‐1
CableEntry ...........................................................................................9‐1
FaciaItems............................................................................................ 9‐2
15”Touchscreen.............................................................................. 9‐2
19”Touchscreen.............................................................................. 9‐2
TouchscreenDimensions ................................................................ 9‐2
HeightsandDepths .........................................................................9‐2
DistanceforVoiceGuidance ...........................................................9‐2
SecurityBolts........................................................................................9‐3
BoltHoles ............................................................................................. 9‐3
ShortSleeve..................................................................................... 9‐3
LongSleeve...................................................................................... 9‐3
HoleintheWall .................................................................................... 9‐4
HoleatOptimumHeight .................................................................9‐4
HoleatLoweredHeight................................................................... 9‐4
HoleintheWallOverlap‐StandardCollar‐ATM...........................9‐5
VentsLocation‐AirFlow......................................................................9‐5
Clearances‐TopboxDoor .................................................................... 9‐5
Clearances‐Corridor............................................................................9‐5
ServicingAreas‐Optimum‐SingleATM.............................................. 9‐6
ShortSleeve .................................................................................... 9‐6
LongSleeve ..................................................................................... 9‐6
ServicingAreas‐Optimum‐SideBySide ............................................ 9‐7
ShortSleeve .................................................................................... 9‐7
LongSleeve ..................................................................................... 9‐7
ServicingAreas‐Minimum‐SingleATM ............................................. 9‐8
ShortSleeve .................................................................................... 9‐8
LongSleeve ..................................................................................... 9‐8
ServicingAreas‐Minimum‐SideBySide ............................................ 9‐9
ShortSleeve .................................................................................... 9‐9
LongSleeve ..................................................................................... 9‐9

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
NCRSelfServ™84Walk‐UpATMSitePreparation
1‐1Introduction
AUDIENCE
Thisdocumentisintendedforarchitectsandthoseresponsibleforpreparinga
sitepriortothearrivaloftheATM.
ABOUTTHISDOCUMENT
Thissitepreparationdocumentisdesignedtobereadonwideaspectratio
screens.Eachsectionhasbeenstructuredtofitthemaximumamountof
informationontheminimumnumberofpagesyetstillbereadablewhen
printedonA3sizepaper.Printingonsmallerpapersizesmayreducereadability
butwillmakehandlingeasier.
Thedocumentisorganisedintosectionscoveringthefollowingtopics:
Introduction‐thissection
CustomerResponsibilities
StandardsCompliance
ProductOverview
SiteRequirements
PowerRequirements
CableRequirements
Decals
VariantDetails‐CENI,StandardCollarATM
VariantDetails‐CENI,OpenCollarATM
VariantDetails‐CENI,StandardAdvertCollar
VariantDetails‐CENI,OpenAdvertCollar
VariantDetails‐CENIIIandIV,StandardCollarATM
VariantDetails‐CENIIIandIV,OpenCollarATM
VariantDetails‐CENIIIandIV,StandardAdvertCollar
VariantDetails‐CENIIIandIV,OpenAdvertCollar
Eachpagehastwoorthreecolumnslaidoutasfollows:
WhereleftandrightsidearestatedtheATMisviewedfromthefront(facia
side)oftheATM.Allplanviewsarefromthetopunlessotherwisestated.
Unlessotherwisestatedalldimensionsareroundedtothenearestmillimetre
andequivalentdecimalofaninch.
REVISIONRECORD
Publication ID
Copyright
Publication name Section name Section number Page number
Column 1 Column 2 Column 3
Date Revision Pages Reason for Change
January 2017 A All Initial release
February 2017 BVarious Hole at Lowered Heights table updated
All modules above 15” touchscreen removed
August 2017 C 9-4, 10-4, 11-4
12-4 Update to Australia plinth height, 5 high 15 in. display
September 2017 DVarious CEN III and IV (Std and GAS EX) added
Modules above 15” touchscreen added to Open collars
Hole at Lowered Heights - new table covering modules
above 15” touchscreen
Safety standard and directive updated
Product Identification label updated
Service clearances updated - LHS/RHS deposit modules
Topbox Clearance added
Note added to weight and floor loading sections
September 2017 E Various Hole at Lowered Heights - update to table covering no
modules above touchscreen
February 2018 F9-2,11-2,13-2&
15-2
9-4,11-4,13-4&
15-4
Modules above 15” touchscreen added back in
(Std and Std Advert Collars)
Modulesabove15”touchscreeninstallationheightstable
added back in
March 2018 G 9-4, 10-4, 11-4,
12-4,13-4,14-4,
15-4, 16-4
Installation height tables updated, 1mm removed from
US plinth and bottom of hole dims

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
NCRSelfServ™84Walk‐UpATMSitePreparation
2‐1CustomerResponsibilities
NOTICE
Thisisacontractualdocument.Itcontainsimportantwarningsandconfers
importantlegalrightsandobligations.Youareadvisedtoreaditcarefully.
Itistheresponsibilityofyou,thecustomer,toassurethatallinstallation
preparationsarecompleteandincompliancewithallspecificationsand
requirementsofNCRandallapplicablenational,state,orlocalcodes,
regulationsandlaws.
Thisequipmentmustbeinstalledandusedinstrictaccordancewiththe
manufacturer’sinstructions.However,thereisnoguaranteethatinterference
toradiocommunicationswillnotoccurinaparticularcommercialinstallation.If
thisequipmentdoescauseinterference,whichcanbedeterminedbyturning
theequipmentoffandon,theuserisencouragedtoconsultanNCRservice
representativeimmediately.
CAUTION NCRCorporationisnotresponsibleforanyradioortelevision
interferencecausedbyunauthorizedmodificationsofthis
equipmentorthesubstitutionorattachmentofconnectingcables
andequipmentotherthanthosespecifiedbyNCR.Such
unauthorizedmodifications,substitutions,orattachmentsmay
voidtheuser’sauthoritytooperatetheequipment.Thecorrection
ofinterferencecausedbysuchunauthorizedmodifications,
substitutions,orattachmentswillbetheresponsibilityoftheuser.
SITECOMPLIANCE
Thisdocumentcontainstheinformationnecessaryforthepreparationofasite
conformingtoNCRspecifications.Itisveryimportantthatthesitecomplies
withtherequirementsspecifiedinthisdocument,because,oncethe
equipmenthasbeeninstalled,deficienciesinsitepreparationortheproblems
causedbythesedeficienciesaremuchmoredifficulttodetectandcorrect.
Further,failuretocomplywiththeserequirementsortotakeproperstepsto
protectequipmentagainstrisksidentifiedinthisdocumentmaycauseserious
damagetotheequipmentandtothecustomer’sbusiness.
Inadditiontotheneedtocomplywiththerequirementsspecified,electrical
wiringandmechanicalsystemsmustalsocomplywithallrelevantcodes,laws
andregulations.
Itisimportantthatthesitebepreparedbyacustomerorhisagentwhoisfully
conversantwiththespecialrequirementsofelectronicequipment.The
responsibilityforensuringthatthesiteispreparedincompliancewiththis
documentremainswiththecustomer.
Forinformationandguidancepurposesonly,alistisprovided,ingeneralterms,
ofthosemattersforwhichthecustomerisresponsible.Thislistisnotintended
tobecomprehensive,andinnowaymodifies,alters,orlimitstheresponsibility
ofthecustomerforallaspectsofadequatesitepreparation.
NCRstaffwillbeavailabletoanswerquestionsrelatingtothecontentsofthis
documentbut,exceptwhere:
a. thecustomerhasbeennotifiedthatafullorpartialconsultancyservice
isavailableand/orthatNCRwillbewillingtoundertakeapreliminaryor
finalsitesurveyand
b. thecustomershallhaveenteredintoaformalcontractwithNCRfor
provisionofthesame
nocomment,suggestionoradviceofferedornotofferedaboutpreparationof
thesitenoranyinspectionofthesitewhetherbeforeorafterpreparationisto
betakenasapprovalofthelocationofthesiteandequipmentorofits
preparationandNCRwillnotbeliableinrespectofanycomment,suggestionor
advicegivenbyitsstafforinrespectofanyfailuretogiveadvice.
Finally,onlythecustomercanknowthefullextentofdamagewhich
maybecausedtohisbusinessbyreasonoffailureoftheequipment
whichistobeinstalled.Forthisreasonitisthecustomer’sresponsibility
toascertaintheextentofanysuchpossibledamagetohisexistingor
plannedbusiness,andtoeffect,fullinsuranceinrespectofit.
CUSTOMERACTIONS
Thecustomermustdoorprovidethefollowing:
WhenrequiredbyNCR,providetheNCRcustomerservice
representativewithappropriatedrawingsthatindicate:
Locationoftheequipment
Sitewiring(powerandsignal,pathsandlengths)
Locationofotherequipmentcapableofgeneratingelectricalnoise,
electromagneticinterference,heat,etc.
Makebuildingalterationsnecessarytomeetwiringandothersite
requirements.
Provideandinstallallcommunicationscables,walljacks,special
connectors,andassociatedhardware.
Provideandinstallnecessarypowerdistributionboxes,conduits,
grounds,lightningprotection,andassociatedhardware.
Makesureallapplicablecodes,regulationsandlaws(including,butnot
limitedto,electrical,building,safety,andhealth)aremet.
Provideandinstallauxiliarypowerorotherequipmentasrequired.
Providestorageorserviceareasasrequired.
Makesuretheenvironmentalrequirementsofthesystem/unitaremet.
Providefloorcoveringsandenvironmentalsystemsthatlimitorcontrol
staticelectricitybuild‐upanddischarge.
Installtheproductataheightwhichmeetstheaccessibilityregulations
oftherelevantcountry.

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
NCRSelfServ™84Walk‐UpATMSitePreparation
3‐1StandardsCompliance
RADIOFREQUENCYINTERFERENCE
FCCRadioFrequencyInterferenceStatement
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClass
Adigitaldevice,pursuanttoPart15oftheFederalCommunications
Commission(FCC)Rules.Theselimitsaredesignedtoprovidereasonable
protectionagainstharmfulinterferencewhentheequipmentisoperatedina
commercialenvironment.Thisequipmentgenerates,uses,andcanradiate
radiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththe
instructionmanual,maycauseharmfulinterferencetoradiocommunications.
Operationofthisequipmentinaresidentialareaislikelytocauseharmful
interferenceinwhichcaseyou,thecustomer,willberequiredtocorrectthe
interferenceatyourownexpense.
CanadianClassADeviceDeclaration
ThisdigitalapparatusdoesnotexceedtheClassAlimitsforradionoise
emissionsfromdigitalapparatussetoutintheRadioInterferenceRegulations
oftheCanadianDepartmentofCommunications.
Leprésentappareilnumériquen’émetpasdebruitsradioélectriquesdépassant
leslimitesapplicablesauxappareilsnumériquesdelaclasseAprescritesdansle
Réglementsurlebrouillageradioélectriqueédictéparleministèredes
CommunicationsduCanada.
SAFETY
SafetyDirective
73/23/EEC,93/68/EEC‘LowVoltageDirectiveandAmendment’.
HarmonisedSafetyStandard
EN60950‐1:2006+A2:2013‘InformationTechnologyEquipment‐
Safety’
ELECTROMAGNETICCOMPATIBILITY(EMC)
ImmunityStandards
TheATMcomplieswiththefollowingrequirementsforradiatedandconducted
immunity:
EN55024(1998)/+A1:2001,A2:2003
AspertherequirementsofEN55024,theATMcomplieswiththerequirements
ofthefollowingnormativeImmunityStandard:
EN61000‐4‐2ElectrostaticDischarge
EN61000‐4‐3RadiatedRF
EN61000‐4‐4ElectricalFastTransient/Burst
EN61000‐4‐5Surge
EN61000‐4‐6ConductedRF
EN61000‐4‐8PowerFrequencyMagneticField
EN61000‐4‐11VoltageDips/ShortInterruption.
EMCDirectives
Thisequipmenthasbeenfoundtocomplywiththeessentialrequirementsof
EMCDirective2014/30/EU,bytestingtoharmonizedstandardsEN55032,
EN55024,EN61000‐3‐2andEN61000‐3.Theequipmentcomplieswiththe
limitsforaClassAdigitaldevice,pursuanttoEN55032.
TheATMcomplieswiththefollowingElectromagneticCompatibility(EMC)
directivesandstandardsforITequipment:
2014/30/EU‘EMCDirective’
93/68/EEC‘CEMarkingDirective’
EmissionStandards
TheATMcomplieswiththefollowingrequirementsforradiatedandconducted
emissions:
EN55032ClassA
FCC47CFRPart15.ClassA
CISPR32ClassA
AS/NZS3548ClassA
GB9254ClassA
CNS13438ClassA.
WARNING ThisequipmentiscompliantwithClassAofCISPR32.Ina
residentialenvironmentthisequipmentmaycauseradio
interference.
AdditionalRequirementsfor220V‐240VUnits
TheATMcomplieswiththefollowingrequirementsforconductedemissions:
EN61000‐3‐2:2000,Mainsharmonics,ClassA
EN61000‐3‐3:1995/+A1:2001,Mainsflicker.
ACCESSIBILITY
Itistheresponsibilityoftheowninginstitutiontoensurethattheheightsfrom
thefloorleveltothefaciaitemscomplywithanylocalregulations.
Note: Theheightslistedinthisdocumentassumethattheinstallationdoes
notadddepthinfrontoftheATM.Increaseddepthmaychangethe
heightrequirementsduetoincreasingtheuser’sreach,therefore
pleaserefertotherelevantaccessibilityregulationifadditionaldepth
hasbeenadded.

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
NCRSelfServ™84Walk‐UpATMSitePreparation
4‐1ProductOverview
GENERALDESCRIPTION
TheNCRSelfServ84Walk‐UpAutomatedTellerMachineisa‘throughthewall’
ATMwhichmaybeinstalledthroughanysuitableexteriorwallorinavestibule
location.
TherearenoseparateVestibuleorThroughtheWallvariantsoftheSelfServ84.
Alldimensionsandclearancesarethesameforbothtypesofinstallation.
Options
StandardSecurityEnclosures
CENGradeI
CENGradeIII
CENGradeIV
SolidandGasExplosionResistant(EXGAS)SecurityEnclosures
CENGradeIII
CENGradeIV
Sleeve
ShortSleeve
LongSleeve
Collars
Standard
StandardAdvert
Open
OpenAdvert
ACOUSTICS
Formostvariantstheacousticssoundpowerdoesnotexceed:
65dB(A)whenidle
68dB(A)whenoperating(seenote).
However,thefollowingconfigurationswillaffectthesoundlevelsasshownin
thetablebelow:
HEATDISSIPATION
TheNCRSelfServproductrangeisaflexiblehardwareplatform.NCR
recommendsthatactualpowermeasurementsaretakenandusedtoestablish
theheatdissipationforspecifichardwareconfigurations.Thesemeasurements
shouldincludeanycustomorthirdpartyfeatures.
Wherespecificmeasurementsarenotavailablethen,asaguide,760KJ/hour
canbeusedasanindicativeheatingload.ThisfigureisbasedonanATMinidle
mode,withamediumtohighfeaturefunctionalityconfiguration.
Heatdissipationfiguresarelargelyunaffectedbytransactionalrates.
PRODUCTIDENTIFICATION
Theillustrationbelowistypicalofthelayoutoftheproductidentificationlabel
whichisfixedinsidetheATM.
Theproductisidentifiedbyaclassanda4digitmodelnumber.Theserial
numberisuniquetoeachATM.Thetracernumberisusedtoidentifywherethe
ATMwasbuilt.
Pleasequotealloftheserialandtracernumbers,includingtheprefix,when
makingreferencetotheATM.
Electricalratinginformationisalsoshownontheproductlabel.
Configuration Acoustic sound power when operating
Coin and passbook does not exceed 72 dB(A)
Cooling fans does not exceed 75 dB(A)
Model: XXXX
Hz: 50/60 A: X.X
XX - XXXXXXXX
Tracer: Serial:
Vãc:
NCR Global Solutions Ltd.
NCR SelfServ XX
™
Made in UK
Electromagnetic Compatibility
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This apparatus does not exceed Class A limits for radio noise emissions set out in the Radio Interference
Regulations of Canada.
Complies with FDA Radiation Performance Standards 21 CFR Subchapter J
Class: XXXX
XX - XX
Manufactured: Xxxxxx XXXX
XXX - XXXv
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe A prescrites dans le Réglement sur le brouillage radioélectrique édicté par le
ministère des Communications du Canada.
Safety Certification Marks are located in this section

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
NCRSelfServ™84Walk‐UpATMSitePreparation
5‐1SiteRequirements
POSITIONINGTHEATM
TheATMmaybeinstalledthroughanysuitableexteriorwallorvestibule
location.
IftheATMisfittedwithaPassbookPrinter,itshouldneverbeexposedtorain
andthereforeonlysuitableforinteriorinstallations.
TheATMmustalsobepositionedawayfromheatsourcesoranyair
conditioningequipment.
Brightlightsandwindowsbehindtheusermaydegradecameraperformance.
PositiontheATMawayfromdirectsunlight.
Allowsufficientroomforinstallationandservicingrequirements.
FLOOR
TheATMmustbeinstalledonalevel,even,concreteorothernoncombustible
surface.Inlocationswherethefloormaybeuneven,itisrecommendedthata
steelplateisusedundertheATM.
Anantistaticfloorcoveringshouldbeusedandmustbeofatypethatwillnot
generatedustorfluff.
TheATMmustbeinstalledonafloorcapableofsupportingthemaximum
weightincludingmedia.Onlythemaximumweightshouldbeconsideredas
additionaloptionsmaybeaddedafterinstallation.Floorloadingiscalculatedby
dividingthemaximumweightoftheATMbythesurfaceareaoftheATMbase
incontactwiththefloor.
Serviceareas,ATMweightsandfloorloadingforyourATMcanbefoundinthe
VariantDetailssections.
DOORWAYSANDCORRIDORS
Makesurethatdoorwaysandcorridorsleadingtoyourpointofinstallationare
wideenoughtoallowthepackagetopassthrough,ormakearrangementsto
unpacktheATMandremoveitfromthepalletinanareawithsufficientaccess
thenmoveittotheinstallationsite.
MakesurethatanycorridorscansupporttheweightoftheATM,includingall
packagingandthepallet.
WALL
A25mm(1.0in.)widesmoothsurfaceisrequiredaroundtheedgeofthewall
openingtoenableagoodweatherseal.
WallCavity
Anycavityinthewallmustbesealedtoprovideaflushsurfacethatdoesnot
extendintothewallopening.LeavethegapbetweentheATMsleeveandthe
wallopeningcleartoallowairatroomtemperaturetocirculate.
InstallingThroughaGlassWall
IfyouareinstallingyourATMthroughaglasswallyoumayrequireasuitable
glasssupport(normallyasteelcollar)tositbetweentheATMcollarandthe
glass.Therequirementforthissupportshouldbedeterminedbythearchitect.
Ifrequired,anysuchsupportshouldbesourcedlocally.
CollarTolerance
Thecollarhasatoleranceof±4mm(0.2in.(±0.5°))atthetopandbottom,with
0mm(0.0in.(0°))atitscentre.
Thecollarcannotaccommodatelargedipsordepressionsinthewall.Make
surethewallissmoothandeven.
AMBIENTLIGHTING
IftheATMisfittedwithacamera,itisstronglyrecommendedthatthereisa
minimumof50LUXlightingatfloorlevelwithintheareaillustratedbelow.
TASKLIGHTING
Aminimumof200LUXisrequiredfortasklighting.
0 mm
(0.0 in.)
±4 mm
(0.16 in.)
±4 mm
(0.16 in.)
1500 mm
(59.1 in.)
1000 mm
(39.4 in.)

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
SiteRequirements
NCRSelfServ™84Walk‐UpATMSitePreparation
5‐2
TEMPERATUREANDHUMIDITY
Continuousoperatingatorneartherangelimits,orinalocationwherethe
temperatureandhumiditychangebeyondthespecification,shouldbeavoided.
Ifinstallingthoughanexteriorwall,thesitemustmeettherequirementsof
boththeInteriorandExteriorenvironments.
Note: ForexteriorthroughthewallATMsthehumidityinsidethebuildingis
restrictedtoamaximumof30%atanoutsidetemperatureof‐35°C
(‐31°F),withalinearrelationshipbetweentemperatureandhumidityto
amaximumhumidityat0°C(32°F).
NormalOperatingRange(InteriorEnvironment)
Temperature:0°Cto40°C(32°Fto104°F)
RelativeHumidity:20%to80%
DewPointTemperatureRestriction:26°C(79°F)maximum
NormalOperatingRange(ExteriorEnvironment)
Temperature:
withoutPassbookPrinter:‐35°Cto50°C(‐31°Fto122°F)
withPassbookPrinter:0°Cto40°C(32°Fto104°F)
RelativeHumidity:
withoutPassbookPrinter:10%to100%
withPassbookPrinterfitted:10%to80%
DewPointTemperatureRestriction:26°C(79°F)maximum
StorageRange(UpToThreeMonths)
Temperature:‐10°Cto50°C(14°Fto122°F)
RelativeHumidity:10%to90%
TransitRange(UpToOneWeek)
Temperature:‐40°Cto60°C(‐40°Fto140°F)
RelativeHumidity:5%to95%
ExtremePowerOnRange(UpToOneHour)
Temperature:0°Cto45°C(32°Fto113°F)
RelativeHumidity:10%to95%
BAROMETRICPRESSURE
Operating/TransitLimits:105kPa(15.2lbf/in2.)to70kPa(10.2lbf/in2.)
EquivalentAltitude:Uptoamaximumof3000m(9842.52ft)

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
NCRSelfServ™84Walk‐UpATMSitePreparation
6‐1PowerRequirements
ACPOWERREQUIREMENTS
Themaximumcurrentrequirementsare:
10Aat120V
6.3Aat230V.
Themaximuminrushcurrentis100A.
NCRdoesnotrecommendrunninganATMwithdepositdeviceswithoutan
UninterruptiblePowerSupply(UPS).WithoutaUPS,thereisthepotentialfor
customer’scashtoberetainedinthedeviceifthereisapowerfailure.
INPUTVOLTAGESETTING
TheATMcanoperatefromthefollowinginputmainsvoltages:
90Vto136Vat50/60Hz
180Vto264Vat50/60Hz.
GROUNDING
TheATMoperatesfromasinglephase,3wiresupply:live,neutralandground.
TheATMpowerrequirementswillnormallypermitittooperatewithinexisting
wiringconfigurationsandfromexistingmainsoutletsprovidedthat:
thebranchcircuitofthedistributionpanelsupplyingtheATMisnotalso
usedtosupplyequipmentwithheavyinductiveloadssuchasair
conditionersorACmotors.
otherbranchcircuitsonthesamedistributionpaneldonotsupplysuch
equipment.
theinstallationmeetsorexceedstheregulatoryandlocalguidelines
withregardtoelectricalsafetyandallconductorsizing.
ThenormalandsafeoperationofthisATMisdependentontheabove.Only
qualifiedpersonnelthatmeetlocalcertificationstandardsshouldbepermitted
toensurecompliance.
Notethatthebuildinggroundpointcanalsoaffectdataintegrity.Foradditional
informationrefertoDataLineTransientProtectionintheCableRequirements
section
TRANSIENTPROTECTION
Intheprocessofpowerdistribution,transientelectricalenergy(including,but
notlimitedto,lightningstrikes,intermittentshortcircuits,andswitching
transients)canbeintroducedontopowerlines.Suchtransientenergycanbe
verydamagingtoelectronichardwareandcanalsocausedatacorruption.
Underthesecircumstances,NCRrecommendstheuseofACpowertransient
suppressorsanddata(communication)linetransientsuppressors.Such
protectivedevicesareintendedtoguardagainstpoweranddatalinetransients
thatcanresultinhardwaredamageandvarioussystemorprogramerrors.
Improvementofanydeficienciesinpowerqualityisacustomerresponsibility.
Malfunctionand/orcomponentfailureasaresultofpowerqualityproblems
are/isnotcoveredbyNCRCorporationMaintenanceAgreement.NCRaccepts
noliabilityforanysuchoccurrencenorforitsconsequences.
Whenpowertransientsuppressionisrequired,thesuppressorsusedshould
meetthefollowingminimumrequirements:
Dissipateenergytomatchtheappropriateapplicationcategoriesas
definedbyANSI/IEEEStandardC62.41,GuideonSurgeVoltagesinLow‐
VoltageACPowerCircuits.
Beofthevoltagelimiting(clipping),ortrackingfiltertype.The
suppressormustnot‘clamp’thevoltagetozero,andmustself‐recover
afterthepassageofthetransient.Thesuppressormaybeofthehybrid
typeconstructionthatmakesuseofvarioustechnologiesinorderto
meetspeedanddissipationrequirements.
Exhibita‘shortcircuit’modeuponitsfailure,thusprovidingapositive
indicationofitsfailuresuchasablownfuseortrippedbreaker
Belistedbytheacceptedsafetyorganizationforthecountryinvolved
(e.g.UL,CSA,VDE,ETL,etc.)andtheinstallationmustconformtolocal,
state,andnationalelectricalcodesandregulations.
Location Category Comparable to IEC
No 664 Category Transient
Waveform Amplitudes
B = Major feeders, short branch
circuits, and load centres III
Volts = 1.2 x 50 s
Current = 8 x 20 s
and
0.5 Rise - 100 kHz
Ringwave
6kV
3kA
6kV
500A
C = Service Entrance and run to
load centre IV Volts = 1.2 x 50 s Current = 8 x 20 s 10kV or more 10kA or more






NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
NCRSelfServ™84Walk‐UpATMSitePreparation
7‐1CableRequirements
CABLEPREPARATION
NCRsupplyapowercablefortheATM.Otherexternalcablesarenotsupplied.
Specificationsforthesecablesaregiveninthissection.
Itisthecustomer’sresponsibilitytohaveanyrequiredexternalcablesinstalled
andtomakesurethatallcablepreparationscomplywithNCRspecificationsas
wellaswithallnational,stateorlocaltelephoneandtelegraphregulationsand
laws.
Whenproducingcablesallowfor2.2m(7.22ft)ofcablewithintheATM.
DATALINETRANSIENTPROTECTION
Voltagetransients,linenoise,surges,sags,impulses,andspikesmaybe
experiencedroutinelyorsporadically.Whensuchphenomenaoccurtheuseof
protectivedevicesmayberequiredtoensureproperoperationofthe
equipment.
Itistheresponsibilityofthecustomertoinstallandconnectadataline
transientsuppressionsystemtocorrectorpreventanydeficiencies.Such
systemsmustmeetthefollowingminimumrequirements:
Beoftheself‐recoveringvoltagelimitingtype.Exhibita‘shortcircuit’mode
uponitsfailuretoensureapositiveindicationofitsfailure.Insertminimum
inductiveandcapacityloadingattheoperatingfrequency.Beinstalledin
accordancewithallapplicablelocal,state,andnationalelectricalcodesand
regulations.
Protectthedataportfromdamageinthepresenceofadatalinetransient
eventasdefinedinIECStandard1000‐4‐5(formerlyIEC801‐5).
ALARMINTERFACECABLES
TheATMmayoptionallybeconfiguredtoprovideanalarminterfacewhich
enablestheATMtobeconnectedtoanexternallocalalarmsystem.The
interfacemaytaketheformofoneoftwooptions;abasicalarmsystemoran
enhancedalarmsystem.
Astabilised,non‐interruptiblepowersupplymustbeprovidedthroughthe
externalalarmsystem.Thealarminterfacecablewiringmustconformtothe
followingspecification:
12V±2Vdc
200mAmaximum
Ripple,5%maximum.
BasicAlarmCable
Removea20mm(0.79in.)sectionoftheoutersleeve,100mm(3.94in.)from
theATMendofthecable.
Takecarenottocutthroughthecableshielding.
EnhancedAlarmCable
Removea20mm(0.79in.)sectionoftheoutersleeve,100mm(3.94in.)from
theATMendofthecable.
Takecarenottocutthroughthecableshielding.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1, 2, 5, 6
3
4
1. Connector, 25 Way (NCR part no. 006-0005896)
2. Terminal, wire, female (NCR part no. 009-0002640)
3. Cable, multiconductor (determined by the alarm installed).
4. Connector (determined by remote device).
5. Shell Hood (NCR part no. 006- ).
6. Screw retainer (NCR part no. 601-0101584).
1500038
Chassis GND
Silent Alarm Common *
Door Alarm N.O.
Door Alarm N.C.
Common
+12V
Silent Alarm N.O. *
Silent Alarm N.C. *
Door Alarm Common
N.O.
N.C
+12V Return
Vibration/Heat
Vibration/Heat
Vibration/Heat
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
* Optional
20 mm
(0.79 in.)
100 mm
(3.94 in.)
1, 2, 5, 6
3
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1. Connector, 25 Way (NCR part no. 006-0005896)
2. Terminal, wire, female (NCR part no. 009-0002640)
3. Cable, multiconductor (determined by the alarm installed).
4. Connector (determined by remote device).
5. Shell Hood (NCR part no. 006- ).
6. Screw retainer (NCR part no. 601-0101584).
1500038
Chassis GND
Test Transmitter A
Tamper Alarm N.O.
Tamper Alarm N.C
Silent Alarm Common *
Door Alarm N.O.
Door Alarm N.C.
Composite Attack Common
+12V
Test Transmitter B
Tamper Alarm Common
Silent Alarm N.O. *
Silent Alarm N.C. *
Door Alarm Common
Composite Attack N.O.
Composite Attack N.C
+12V Return
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
* Optional
20 mm
(0.79 in.)
100 mm
(3.94 in.)

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
CableRequirements
NCRSelfServ™84Walk‐UpATMSitePreparation
7‐2
REMOTESTATUSMONITOR
Theremotestatusmonitorfeatureissuppliedasacompleteassembly
consistingofastatusindicatorunit,76.2m(250ft)ofcableandaconnector.
Removea20mm(0.79in.)sectionoftheoutersleeve,70mm(2.76in.)from
theATMendofthecable.
Takecarenottocutthroughthecableshielding.
ShorteningtheCable
Ifyouneedtoshortenthecable,proceedasfollows:
1. Removethecoverfromtheremotestatusindicatorunit
2. Disconnectthefourleads(E1,E2,E3andE4)fromtheindicator
3. Cutthecabletotherequiredlengthandstripthefourwireends
4. Connectthewirestothecorrectterminals
5. Replacethestatusindicatorcover.
REMOTERELAYCABLE
Theremoterelayprovidesapairofopencontacts,ratedat28voltsperampere
forbothacanddcsupplies,whichcanbeclosedtoactivatearemotedevice.
Theinterconnectingcabletoaremotedevicemustconformtothefollowing
specificationandwiring:
Removea20mm(0.79in.)sectionoftheoutersleeve,100mm(3.94in.)from
theATMendofthecable.
Takecarenottocutthroughthecableshielding.
ETHERNETSTANDARDCABLE
Theethernetstandardcablemustbefullyshielded,8pin,Category5compliant
andmustnotexceed97m(318.20ft)inlength.
Removea40mm(1.57in.)sectionoftheoutersleeve,80mm(3.15in.)from
theATMendofthecable.
Takecarenottocutthroughthecableshielding.
POWERCABLE
TheATMissuppliedeitherasa120Vora220‐240Vunit.
120VATMsaresuppliedwithapowercablefittedwithaNEMAtype5‐15P
powersourceconnector.
220‐240VATMsaresuppliedwithanunterminatedpowercable.Information
aboutsuitablepowerconnectorsissuppliedwiththeaccessories.
Thepowercablesuppliedis3m(9.84ft)inlength.Ifitisnecessarytoincrease
thislengthtomeetsiterequirements,thentheextensionmustsatisfylocalor
countryregulations.
WARNING Thisequipmentmustbeearthed.
70 mm
(2.76 in.)
20 mm
(0.79 in.)
(Green) E1
(Red) E2
(White) E3
(Black) E4
Red
Yellow
Green
1
2
1, 2 34
Rl1
RL2
1. Connector, 2 way Mate-N-Lock (NCR part no. 007-9814285).
2. Terminal wire, male (NCR part no. 007-2009663).
3. Cable, multiconductor (NCR part no. 006-5800006).
4. Connector (determined by remote device).
20 mm
(0.79 in.)
100 mm
(3.94 in.)
40 mm
(1.57 in.)
80 mm
(3.15 in.)

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
NCRSelfServ™84Walk‐UpATMSitePreparation
8‐1Decals
ADVERTWINDOW
Thedecalsshouldbeamaximumof0.75mm(0.0295in.)thick.
AdvertCollarorOpenAdvertCollar
ENTRY/EXITDECALS
Entry/Exitdecalsshouldbeamaximumof0.5mm(0.02in.)thick.NCR
recommendstheybemadefromtexturedpolycarbonatewith3M467High
PerformanceMPadhesive.
Decalsshouldprovidegoodcontrast,atleast70%,betweenforeground(text/
icon)andbackground.
Asansseriftypefaceshouldbeused(Tiresiasisrecommended).Thetextsize
shouldbeatleast14point,andlargerwherepossible.Wheretactiledecalsare
requiredtheyshouldbedesignedinlinewithspecificcountryrequirements.
Suggestedicondesignsandwordingareshownbelow:
CAUTION Whenplacinganycardreaderdecal,makesurethatthelabeldoes
notobscurethecontactlesscardreaderorcardreaderentryslot
lights.
CAUTION DoNOTplaceanymetalliccoatedorsubstratelabelontheglass
areaaroundtheCCRorcardreader,highlightedbelow:
595.5 mm
(23.44 in.)
2.5 mm
(0.10 in.)
Radius in
four corners
160 mm
(6.30 in.)
Cash Deposit
Cash Dispense
Receipt
Cash
Dispense/Deposit Cheque Deposit
1234 5678 9
Coin Dispense
Statement
Cash/Cheque
Deposit
1234 5678 9
Statement and
Passbook Printer
Passbook Printer
12 mm
(0.47 in.)
75 mm
(2.95 in.)

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
NCRSelfServ™84Walk‐UpATMSitePreparation
9‐1VariantDetails‐CENI,StandardCollarATM
PACKAGEDIMENSIONS ATMDIMENSIONS WEIGHTANDFLOORLOADING
Note: Themaximumweightcoversthemaximumconfigurationpossiblefor
theATM.Thiswillincludeallmodules(coindispenser,cashacceptor,
statementprinter,etc)fullyloadedwithmedia.
StandardSecurityEnclosures
CABLEENTRY
1989 mm
(78.31 in.)
1398 mm
(55.04 in.)
950 mm
(37.40 in.)
958 mm
(37.72 in.)
1405 mm
(55.31 in.)
A
A - 1847 mm (72.72 in.) with a 5 High Security Enclosure
1729 mm (68.07 in.) with a 4 High Security Enclosure
Note 1
340 mm
(13.39 in.)
1248 mm
(49.13 in.)
including
lock
66 mm
(2.60 in.)
801 mm
(31.54 in.)
373 mm
(14.68 in.)
1134 mm
(44.65 in.)
including
lock
1513 mm
(59.57 in.)
770 mm
(30.31 in.)
832 mm
(32.76 in.)
*664 mm
(26.14 in.)
800 mm
(31.50 in.)
801 mm
(31.54 in.)
259 mm
(10.20 in.)
226 mm
(8.90 in.)
66 mm
(2.60 in.)
Note 1
60 mm
(2.36 in.)
681 mm
(26.81 in.)
502 mm
(19.76 in.)
62 mm
(2.44 in.) Note 2
Note 2
62 mm
(2.44 in.)
1631 mm
(64.21 in.)
770 mm
(30.31 in.)
744.5 mm
(29.31 in.)
615 mm
(24.21 in.)
271.5 mm
(10.69 in.)
626.5 mm
(24.67 in.)
615 mm
(24.21 in.)
271.5 mm
(10.69 in.)
950 mm
(37.40 in.)
60 mm
(2.36 in.)
681 mm
(26.81 in.)
502 mm
(19.76 in.)
*782 mm
(30.79 in.)
800 mm
(31.50 in.)
719 mm
(28.31 in.)
719 mm
(28.31 in.)
* Dimensions are the same for short or long sleeve options
: 610 mm (24.02 in.) without cash camera
617.3 mm (24.30 in.) including cash camera
Note 1
Note 2: 98 mm (3.86 in.) without cash camera option
90.7 mm (3.57 in.) with cash camera option
4 High Security
Enclosure
5 High Security
Enclosure
4 High Security
Enclosure
5 High Security
Enclosure
Short Sleeve Long Sleeve
CEN Grade I
4 High CEN Grade I 5 High
Maximum weight 904.70 kg
(1994.52 lb.) 949.70 kg (2093.73 lb.)
Floor loading 1469 kg/m2
(300.8 lb./ft2)1542 kg/m2 (315.7 lb./ft2)
555 mm
(21.85 in.)
212 mm
(8.35 in.)
33 mm
(1.30 in.)
65.5 mm
(2.58 in.)
800 mm
(31.50 in.)
770 mm
(30.31 in.)

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
VariantDetails‐CENI,StandardCollarATM
NCRSelfServ™84Walk‐UpATMSitePreparation
9‐2
FACIAITEMS
15”Touchscreen
19”Touchscreen
TouchscreenDimensions
HeightsandDepths DistanceforVoiceGuidance
Touchscreen
Size Touchscreen Height x Width Touchscreen Angle
15 inch 234 mm x 310 mm
9.21 in. x 12.20 in. 30 degrees from vertical
19 inch 305 mm x 380 mm
12.01 in. x 14.96 in. 30 degrees from vertical
5
JKL
S
$
1234 5678 9 1234 5678 9
S
S
5
JKL
S
Facia Item
Height from
base of ATM
(4-High
Dispenser Safe)
Height from
base of ATM
(5-High
Dispenser Safe)
Depth
from front
of shelf
Cheque Entry 1089 mm
(42.87 in.) 1207 mm (47.52 in.) 218 mm (8.58 in.)
Passbook Entry/Exit 1086 mm
(42.76 in.) 1204 mm (47.40 in.) 218.5 mm (8.60 in.)
Statement Exit 1084 mm
(42.68 in.) 1202 mm (47.32 in.) 218 mm (8.58 in.)
ID Scanner 1082 mm
(42.60 in.) 1200 mm (47.24 in.) 236 mm (9.29 in.)
Coin Exit 1075 mm
(42.32 in.) 1193 mm (46.97 in.) 234 mm (9.21 in.)
Touchscreen - Top
483 mm (19.0 in.) 1074 mm (42.28 in.) 1192 mm (46.93 in.) 221 mm (8.70 in.)
Receipt 1031 mm
(40.59 in.) 1149 mm (45.24 in.) 185 mm (7.28 in.)
Touchscreen - Top
381 mm (15.0 in.) 1022 mm (40.24 in.) 1140 mm (44.88 in.) 191 mm (7.52 in.)
Card Reader 915 mm
(36.02 in.) 1033 mm (40.67 in.) 165 mm (6.50 in.)
Contactless Card Reader (behind Facia) 915 mm
(36.02 in.) 1033 mm (40.67 in.) 165 mm (6.50 in.)
PIN Pad - Number 5 Key 849 mm
(33.43 in.) 967 mm (38.07 in.) 136.5 mm (5.37 in.)
Private Audio 780 mm
(30.71 in.) 898 mm (35.35 in.) 59 mm (2.32 in.)
Barcode Reader - Activation Point 757 mm
(29.80 in.) 875 mm (34.45 in.) 33 mm (1.30 in.)
Cash Exit/Entry 747 mm
(29.41 in.) 865 mm (34.05 in.) 73 mm (2.87 in.)
Scalable Deposit Module 747 mm
(29.41 in.) 865 mm (34.05 in.) 73 mm (2.87 in.)
$
5
JKL
S
1234 5678 9
No. 5 Key Audio Jack
Facia Item Distance to
Facia Item Distance to Facia Item
Receipt 1193 mm
(7.60 in.) 1277 mm
(10.91 in.)
Card Reader 286 mm
(3.39 in.) 1169 mm (6.65 in.)
Private Audio 6100 mm
(3.94 in.) --
Cash Exit/Entry Right
hand 7127 mm (5.00 in.) 765 mm (2.56 in.)
Scalable Deposit Module Right
hand 7127 mm (5.00 in.) 765 mm (2.56 in.)
Barcode Reader -
Activation Point 7146 mm (5.75 in.) 873 mm (2.87 in.)
Scalable Deposit Module Left
hand 8354 mm (13.94 in.) 973 mm (2.87 in.)
Cash Exit/Entry Left
hand 8354 mm (13.94 in.) 973 mm (2.87 in.)
Touchscreen
381 mm (15.0 in.) Centre 10 284 mm
(11.18 in.) 10 329 mm
(12.95 in.)
Touchscreen
483 mm (19.0 in.) Centre 10 290 mm (11.42 in.) 10 341 mm (13.43 in.)
Passbook Entry/Exit 10 314 mm
(12.36 in.) 10 396 mm (15.59 in.)
Cheque Entry 10 481 mm
(18.82 in.) 10 545 mm (21.46 in.)
ID Scanner 10 482 mm
(18.98 in.) 10 547 mm (21.54 in.)
ContactlessCardReader
(behind Facia) 11 77 mm (3.03 in.) 11 171 mm (6.73 in.)
Coin Exit 11 275 mm
(10.83 in.) 11 365 mm (14.37 in.)
Statement Exit 11 312 mm
(12.28 in.) 11 395 mm (15.55 in.)
12
11
10
9
87654
3
2
1
12
11
10
9
87654
3
2
1
S
1234 5678 9
1234 5678 9
S
$

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
VariantDetails‐CENI,StandardCollarATM
NCRSelfServ™84Walk‐UpATMSitePreparation
9‐3
SECURITYBOLTS
Boltsandanchorsmustbesuppliedbytheowningorganisation.
TomeetsecuritystandardstheATMmustbeboltedtothefloor,throughallof
theboltholes,usingboltswithanchorwashersasspecifiedbelow.Boltsand
anchorwashersaretobesuppliedbytheowningorganisation.
Makesurethatthefloororplinthiscapableofwithstandingtheloading
imposedbytheanchorpointsforthesebolts.
Ifanadjustableplinthisused,itmustbeboltedtothefloortothesame
specificationastheATM.
TheminimumspecificationforboltsandwasherstosecuretheATMtoa
concreteflooris:
Bolts
Type‐eitherresinanchororshieldanchorbolts
Size‐M16(5/8in.)
MinimumLength‐150mm(5.9in.)
Strength‐hightensile(minimumISOpropertyclass8,8).
Washers
Type‐flat,steel(asperDIN7349orequivalent)
Size‐M16(5/8in.)
Outerdiameter‐nogreaterthan40mm(1.58in.)
Minimumthickness‐6mm(0.2in.).
BOLTHOLES
TheATMshouldbeboltedtothefloororplinth,throughalltheholesmarked
‘A’,usingfourboltswithanchorwashers.
Theholemarked‘B’enablesanalarmtobefitted.
ShortSleeve
LongSleeve
B
A
A
A
A
Hole in Wall
203 mm (7.99 in.)
Maximum
390 mm
(15.35 in.)
500 mm
(19.68 in.)
250 mm
(9.84 in.)
284.5 mm
(11.20 in.)
770 mm
(30.31 in.)
169.5 mm
(6.67 in.)
800 mm
(31.50 in.)
164 mm
(6.46 in.)
500 mm
(19.68 in.)
250 mm
(9.84 in.)
136 mm
(5.35 in.)
18 mm
(0.70 in.)
100.5 mm
(3.96 in.)
Hole A Bolt Holes Hole B (Alarm Hole)
40 mm
(1.57 in.)
40 mm
(1.57 in.)
21 mm
(0.83 in.)
25 mm
(0.98 in.)
28 mm
(1.10 in.)
65 mm
(2.56 in.)
45 mm
(1.77 in.)
28 mm
(1.10 in.)
B
A
A
A
A
Hole A Bolt Holes Hole B (Alarm Hole)
330 mm
(12.99 in.)
Maximum
504 mm
(19.84 in.)
Hole in Wall
500 mm
(19.68 in.)
250 mm
(9.84 in.)
284.5 mm
(11.20 in.)
770 mm
(30.31 in.)
169.5 mm
(6.67 in.)
800 mm
(31.50 in.)
164 mm
(6.46 in.)
500 mm
(19.68 in.)
250 mm
(9.84 in.)
136 mm
(5.35 in.)
18 mm
(0.70 in.)
100.5 mm
(3.96 in.)
40 mm
(1.57 in.)
40 mm
(1.57 in.)
21 mm
(0.83 in.)
25 mm
(0.98 in.)
28 mm
(1.10 in.)
65 mm
(2.56 in.)
45 mm
(1.77 in.)
28 mm
(1.10 in.)

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
VariantDetails‐CENI,StandardCollarATM
NCRSelfServ™84Walk‐UpATMSitePreparation
9‐4
HOLEINTHEWALL
HoleatOptimumHeight
Thisheightassuresthebestdisplayviewabilityforable‐bodiedpeople.Itdoes
NOTcomplywiththeloweredheightregulationslistedinthenextsection.
4HighSecurityEnclosure
5HighSecurityEnclosure
HoleatLoweredHeight
Itistheresponsibilityoftheowninginstitutiontomakesurethattheheight
fromthesidewalkleveltothehighestoperablepointonthefacia(see‘Facia
Items’)complieswithanylocalregulations.Theinformationcontainedinthe
followingtablesincludethemaximumplinthheightsforthecountrieslisted
andareshownasexamples.
Forcorrectinstallationheightyoumustconsiderthedifferenceinheight
betweenthesidewalkandtheinteriorfloor,andinstalltheATMonaplinthif
necessary.
NotethatCENcertifiedsecurityenclosuresmusthaveaCENcertifiedplinth.
StandardCollar
Short Sleeve - maximum (7.99 in.)
Long Sleeve - maximum (12.99 in.)
203 mm
330 mm
534 mm
(21.02 in.)
368 mm
(14.49 in.)
18 mm
(0.71 in.)
*625 mm
(24.61 in.)
1026 mm
(40.39 in.)
Hole in Wall
ATM Base
View from
Inside Building
Plinth
Sidewalk
*increase to 635 mm (25.00 in.) if ATM installed with cash camera
Hole in Wall
534 mm
(21.02 in.)
*625 mm
(24.61 in.)
Short Sleeve - maximum (7.99 in.)
Long Sleeve - maximum (12.99 in.)
203 mm
330 mm
250 mm
(9.84 in.)
18 mm
(0.71 in.)
1026 mm
(40.39 in.)
ATM Base
View from
Inside Building
Plinth
Sidewalk
*increase to 635 mm (25.00 in.) if ATM installed with cash camera
Short Sleeve - maximum (7.99 in.)
Long Sleeve - maximum (12.99 in.)
203 mm
330 mm
534 mm
(21.02 in.)
B
18 mm
(0.71 in.)
*625 mm
(24.61 in.)
A
Hole in Wall
ATM Base
View from
Inside Building
Plinth
Sidewalk
*increase to 635 mm (25.00 in.) if ATM installed with cash camera
Installation Height - ATM with no modules above touchscreen
UK (CAE Parallel Approach)
4 High with 15 in.
Touchscreen 5 High with 15 in. Touchscreen 4 High with 19 in. Touchscreen 5 High with 19 in. Touchscreen
A - Bottom of hole 847 mm
(33.35 in.) 847 mm (33.35 in.) 734 mm (28.90 in.) 776 mm (30.55 in.)
B - Plinth height 189 mm
(7.44 in.) 71 mm (2.80 in.) 76 mm (2.99 in.) 0 mm (0 in.)
USA (ADA)
4 High with 15 in.
Touchscreen 5 High with 15 in. Touchscreen 4 High with 19 in. Touchscreen 5 High with 19 in. Touchscreen
A - Bottom of hole 846 mm
(33.31 in.) 846 mm (33.31 in.) 803 mm (31.61 in.) 803 mm (31.61 in.)
B - Plinth height 188 mm
(7.40 in.) 70 mm (2.76 in.) 145 mm (5.71 in.) 27 mm (1.06 in.)
Canada & Australia (CSA Parallel Approach)
4 High with 15 in.
Touchscreen 5 High with 15 in. Touchscreen 4 High with 19 in. Touchscreen 5 High with 19 in. Touchscreen
A - Bottom of hole
CANADA
827 mm (32.56 in.)
AUSTRALIA
759 mm (29.88 in.)
CANADA
827 mm (32.56 in.)
AUSTRALIA
776 mm (30.55 in.)
759 mm
(29.88 in.) 776 mm (30.55 in.)
B - Plinth height
CANADA
169 mm (6.65 in.)
AUSTRALIA
101 mm (3.98 in.)
CANADA
51 mm (2.01 in.)
AUSTRALIA
0 mm (0 in.)
101 mm
(3.98 in.) 0 mm (0 in.)
Installation Height - ATM with modules above
touchscreen
UK (CAE Parallel Approach)
4 High with 15 in.
Touchscreen 5 High with 15 in. Touchscreen
A - Bottom of hole 719 mm
(28.31 in.) 776 mm (30.55 in.)
B - Plinth height 61 mm
(2.40 in.) 0 mm (0 in.)
USA (ADA)
4 High with 15 in.
Touchscreen 5 High with 15 in. Touchscreen
A - Bottom of hole 788 mm
(31.02 in.) 788 mm (31.02 in.)
B - Plinth height 130 mm
(5.12 in.) 12 mm (0.47 in.)
Canada & Australia (CSA Parallel
Approach)
4 High with 15 in.
Touchscreen 5 High with 15 in. Touchscreen
A - Bottom of hole
CANADA
769 mm (30.28 in.)
AUSTRALIA
759 mm (29.88 in.)
776 mm
(30.55 in.)
B - Plinth height
CANADA
111 mm (4.37 in.)
AUSTRALIA
101 mm (3.98 in.)
0 mm
(0 in.)
DO NOT USE
NOT USED

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
VariantDetails‐CENI,StandardCollarATM
NCRSelfServ™84Walk‐UpATMSitePreparation
9‐5
HoleintheWallOverlap‐StandardCollar‐ATM VENTSLOCATION‐AIRFLOW
Unrestrictedairflowisrequiredonboththeleftandrighthandsideandatthe
rearoftheATM.Theremustbenoobstructionoftheventsatanytime.
Ifathird‐partysurround/topperisfittedthenequivalentventing,orahotair
extractionsystemmustbeinstalledwithinthesurround/topper.
CLEARANCES‐TOPBOXDOOR
CLEARANCES‐CORRIDOR
ThedimensionsshownassumetheATMisbeingmovedusingequipmentthat
doesnotextendbeyondtheATMorpackaging.
Asurroundingclearanceof6mm(0.24in.)hasbeenallowedinthedimensions.
*47 mm
(1.85 in.)
31.5 mm
(1.24 in.)
49.5 mm
(1.95 in.)
*47 mm
(1.85 in.)
*decreased to 42 mm (1.65 in.) if ATM installed with cash camera
8 mm
(0.31 in.)
371.5 mm
(14.63 in.)
24 mm
(0.94 in.)
74.5 mm
(2.93 in.)
274 mm
(10.79 in.)
221.5 mm
(8.72 in.) 93 mm
(3.66 in.)
93 mm
(3.66 in.)
119 mm
(4.68 in.)
40 mm
(1.57 in.)
48 mm
(1.89 in.)
132 mm
(5.20 in.)
262.5 mm
(10.33 in.)
*Dim A
1392 mm
(54.80 in.)
591 mm
(23.27 in.)
773 mm
(30.43 in.)
393 mm
(15.47 in.)
28 mm
(1.10 in.)
*Dim A 1903 mm (74.92 in.) - 4 High security enclosure
2021 mm (79.57 in.) - 5 High security enclosure
Packaged ATM
(pallet and
carton)
Unpackaged
ATM
ADoorway or straight corridor 970 mm
(38.19 in.) 782 mm (30.79 in.)
BCorridor with corner 1186 mm
(46.69 in.) 1003 mm (39.49 in.)
CRotation about centre 1713 mm
(67.44 in.) 1478 mm (58.19 in.)
C
B
B
A

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
VariantDetails‐CENI,StandardCollarATM
NCRSelfServ™84Walk‐UpATMSitePreparation
9‐6
SERVICINGAREAS‐OPTIMUM‐SINGLEATM
TheoptimumservicingareaprovidesthebestaccesstotheATMforall
servicingandoperationtasks.
WhereverpossibletheATMshouldbeinstalledwithintheoptimumservicing
area.
IftheoptimumareaisnotavailablethenrefertoServicingAreas‐Minimum.
HowevernotethatinstallingtheATMintheminimumservicingareamay
increasetheservicingand/orupgradingtimeoveraATMinstalledusingthe
optimumarea.
AlwaysleaveasmuchspaceaspossiblearoundtheATMtofacilitatesafe
operationandservicing.
ShortSleeve LongSleeve
750 mm
(29.53 in.)
460 mm
(18.11 in.)
326 mm
(12.83 in.)
1000 mm
(39.37 in.)
2352 mm
(92.60 in.)
203 mm
(7.99 in.)
Maximum
1780 mm
(70.08 in.)
770 mm
(30.31 in.)
525 mm
(20.67 in.)
460 mm
(18.11 in.)
90 mm
(3.54 in.)
25 mm
(0.98 in.)
Rear of
security
enclosure
(door open)
750 mm
(29.53 in.)
460 mm
(18.11 in.)
326 mm
(12.83 in.)
1000 mm
(39.37 in.)
2466 mm
(97.09 in.)
330 mm
(12.99 in.)
Maximum
1780 mm
(70.08 in.)
770 mm
(30.31 in.)
525 mm
(20.67 in.)
460 mm
(18.11 in.)
90 mm
(3.54 in.)
25 mm
(0.98 in.)
Rear of
security
enclosure
(door open)

NCRProprietaryInformation‐nottobedisclosedorreproducedwithoutwrittenconsent.©2017,2018byNCRCorporation,Atlanta,Georgia,U.S.A.http://www.ncr.com.AllRightsReserved B006‐7519‐G000
VariantDetails‐CENI,StandardCollarATM
NCRSelfServ™84Walk‐UpATMSitePreparation
9‐7
SERVICINGAREAS‐OPTIMUM‐SIDEBYSIDE
TheoptimumservicingareaprovidesthebestaccesstotheATMforallservicingandoperationtasks.
WhereverpossibletheATMshouldbeinstalledwithintheoptimumservicingarea.
IftheoptimumareaisnotavailablethenrefertoServicingAreas‐Minimum.HowevernotethatinstallingtheATMinthe
minimumservicingareamayincreasetheservicingand/orupgradingtimeoveraATMinstalledusingtheoptimumarea.
AlwaysleaveasmuchspaceaspossiblearoundtheATMtofacilitatesafeoperationandservicing.
ShortSleeve
LongSleeve
460 mm
(18.11 in.)
3010 mm
(118.50 in.)
770 mm
(30.31 in.)
525 mm
(20.67 in.)
326 mm
(12.83 in.)
1000 mm
(39.37 in.)
2352 mm
(92.60 in.)
203 mm
(7.99 in.)
Maximum
750 mm
(29.53 in.)
460 mm
(18.11 in.)
460 mm
(18.11 in.)
90 mm
(3.54 in.)
25 mm
(0.98 in.)
Rear of
security
enclosure
(door open)
3010 mm
(118.50 in.)
770 mm
(30.31 in.)
525 mm
(20.67 in.)
326 mm
(12.83 in.)
1000 mm
(39.37 in.)
2466 mm
(97.09 in.)
330 mm
(13.00 in.)
Maximum
750 mm
(29.53 in.)
460 mm
(18.11 in.)
460 mm
(18.11 in.)
460 mm
(18.11 in.)
90 mm
(3.54 in.)
25 mm
(0.98 in.)
Rear of
security
enclosure
(door open)