NEC QB-V850ESFJ3 User manual

CUSTOMER NOTIFICATION ZUD-CD-05-0149 1/57
November 11, 2005
Koji Nishibayashi, Group Manager
Development Tool Group
Multipurpose Microcomputer Systems Division
4th Systems Operations Unit
NEC Electronics Corporation
CP(K),O
QB-V850ESFJ3
Target Devices
V850ES/FE3
V850ES/FF3
V850ES/FG3
V850ES/FJ3
In-Circuit Emulator
Preliminary User’s Manual

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 2/57
[MEMO]

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 3/57
IECUBE is a registered trademark of NEC Electronics Corporation in Japan and Germany.
PC/AT is a trademark of International Business Machines Corporation.
MULTI, Green Hills Software, TimeMachine, and SuperTrace are either registered trademarks or trademarks
of Green Hills Software, Inc. in the United States.
The information in this document is current as of November 2005. The information is subject to
change without notice. For actual design-in, refer to the latest publications of NEC Electronics data
sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not
all products and/or types are available in every country. Please check with an NEC Electronics sales
representative for availability and additional information.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may
appear in this document.
NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from the use of NEC Electronics products listed in this document
or any other liability arising from the use of such products. No license, express, implied or otherwise, is
granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.
Descriptions of circuits, software and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these
circuits, software and information in the design of a customer's equipment shall be done under the full
responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by
customers or third parties arising from the use of these circuits, software and information.
While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products,
customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To
minimize risks of damage to property or injury (including death) to persons arising from defects in NEC
Electronics products, customers must incorporate sufficient safety measures in their design, such as
redundancy, fire-containment and anti-failure features.
NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and
"Specific".
The "Specific" quality grade applies only to NEC Electronics products developed based on a customer-
designated "quality assurance program" for a specific application. The recommended applications of an NEC
Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of
each NEC Electronics product before using it in a particular application.
The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC
Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications
not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to
determine NEC Electronics' willingness to support a given application.
(Note)
•
•
•
•
•
•
M8E 02. 11-1
(1)
(2)
"NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its
majority-owned subsidiaries.
"NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as
defined above).
Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment
and industrial robots.
Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support).
Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems and medical equipment for life support, etc.
"Standard":
"Special":
"Specific":

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 4/57
General Precautions for Handling This Product
1. Circumstances not covered by product guarantee
•If the product was disassembled, altered, or repaired by the customer
•If it was dropped, broken, or given another strong shock
•Use at overvoltage, use outside guaranteed temperature range, storing outside guaranteed temperature range
•If power was turned on while the AC adapter, USB interface cable, or connection to the target system was in
an unsatisfactory state
•If the cable of the AC adapter, the USB interface cable, the extension probe, or the like was bent or pulled
excessively
•If an AC adapter other than the supplied product was used
•If the product got wet
•If this product is connected to the target system when there is a potential difference between the GND of this
product and GND of the target system.
•If the connectors or cables are plugged/unplugged while this product is in the power-on state.
•If excessive load is applied to the connectors or sockets.Note
•If a metal part of the power switch, cooling fan, or another such part comes in contact with an electrostatic
charge
Note For details on handling, refer to 2.5 Mounting and Connecting Connectors (When Using S Type) or 2.6
Mounting and Connecting Connectors (When Using T Type).
2. Safety precautions
•If used for a long time, the product may become hot (50°C to 60°C). Be careful of low temperature burns and
other dangers due to the product becoming hot.
•Be careful of electrical shock. There is a danger of electrical shock if the product is used as described above
in 1Circumstances not covered by product guarantee.

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 5/57
INTRODUCTION
Readers This manual is intended for users who wish to perform debugging using the QB-
V850ESFJ3. The readers of this manual are assumed to be familiar with the device
functions and usage, and to have knowledge of debuggers.
Purpose This manual is intended to give users an understanding of the basic specifications
and correct usage of the QB-V850ESFJ3.
Organization This manual is divided into the following sections.
zGeneral
zSetup procedure
zSettings at product shipment
zCautions
zNotes on target system design
zOptional functions
How to Read This Manual It is assumed that the readers of this manual have general knowledge in the fields
of electrical engineering, logic circuits, and microcontrollers.
This manual describes the basic setup procedures and how to set switches.
To understand the overall functions and usages of the QB-V850ESFJ3
→Read this manual according to the CONTENTS.
To know the manipulations, command functions, and other software-related settings
of the QB-V850ESFJ3
→See the user’s manual of the debugger (supplied with the QB-V850ESFJ3) to be
used.
Conventions Note: Footnote for item marked with Note in the text
Caution: Information requiring particular attention
Remark: Supplementary information
Numeric representation: Binary ... xxxx or xxxxB
Decimal ... xxxx
Hexadecimal ... xxxxH
Prefix indicating power of 2 (address space, memory capacity):
K (kilo): 210 = 1,024
M (mega): 220 = 1,0242

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 6/57
Terminology The meanings of the terms used in this manual are described in the table below.
Term Meaning
Target device This is the device to be emulated.
Target system This is the system to be debugged (system provided by the user).
This includes the target program and the hardware provided by the user.
IECUBE®Generic name for NEC Electronics’ high-performance, compact in-circuit
emulator.
Related Documents Please use the following documents in combination with this manual.
The related documents listed below may include preliminary versions. However,
preliminary versions are not marked as such.
{Documents Related to Development Tools (User’s Manuals)
Document Name Document Number
QB-V850ESFJ3 In-Circuit Emulator This document
Operation U17293E
C Language U17291E
Assembly Language U17292E
CA850 Ver. 3.00 C Compiler Package
Link Directives U17294E
ID850QB Ver. 3.10 Integrated Debugger Operation U17435E
Operation U17246ESM+ System Simulator
User Open Interface U17247E
Basics U13430E
Installation U17419E
Technical U13431E
RX850 Ver. 3.20 Real-Time OS
Task Debugger U17420E
Basics U13773E
Installation U17421E
Technical U13772E
RX850 Pro Ver. 3.20 Real-Time OS
Task Debugger U17422E
AZ850 Ver. 3.30 System Performance Analyzer U17423E
PM+ Ver. 6.00 Project Manager U17178E
Caution The related documents listed above are subject to change without
notice. Be sure to use the latest version of each document for
designing, etc.

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 7/57
CONTENTS
CHAPTER 1 GENERAL .........................................................................................9
1.1 Hardware Specifications.............................................................................................................10
1.2 System Specifications.................................................................................................................11
1.3 System Configuration .................................................................................................................12
1.4 Package Contents........................................................................................................................16
CHAPTER 2 SETUP PROCEDURE ....................................................................18
2.1 Names and Functions of Hardware ...........................................................................................19
2.2 Removal of Acrylic Board...........................................................................................................20
2.3 Clock Settings..............................................................................................................................21
2.3.1 Overview of main clock settings............................................................................................................. 21
2.3.2 Main clock settings ................................................................................................................................ 21
2.3.3 Cautions on changing oscillator ............................................................................................................. 22
2.3.4 Overview of subclock settings................................................................................................................ 22
2.3.5 Subclock settings................................................................................................................................... 23
2.4 Software Settings ........................................................................................................................23
2.4.1 When using ID850QB as debugger ....................................................................................................... 23
2.4.2 When using a debugger other than ID850QB (MULTI, etc.) .................................................................. 23
2.5 Mounting and Connecting Connectors (When Using S Type) ................................................24
2.5.1 Mounting TC onto target system............................................................................................................ 24
2.5.2 Inserting EA into TC............................................................................................................................... 24
2.5.3 Precautions for handling TC, EA, MA, CA, and SA................................................................................ 25
2.5.4 Precautions for mounting IC using MA .................................................................................................. 27
2.6 Mounting and Connecting Connectors (When Using T Type) ................................................28
2.6.1 Mounting TC onto target system............................................................................................................ 28
2.6.2 Connecting YQ on TC............................................................................................................................ 28
2.6.3 Inserting EA into YQ .............................................................................................................................. 29
2.6.4 Precautions for handling TC, YQ, SA, and CA....................................................................................... 29
2.6.5 Precautions for mounting IC using TC and MA...................................................................................... 30
2.7 Connecting QB-V850ESFJ3 to Target System .........................................................................31
2.7.1 When not using extension probe (QB-144-EP-01S) .............................................................................. 31
2.7.2 When using extension probe (QB-144-EP-01S) .................................................................................... 32
2.8 Connecting USB Interface Cable and AC Adapter ...................................................................36
2.9 Switching Power On and Off ......................................................................................................36
CHAPTER 3 SETTINGS AT PRODUCT SHIPMENT ........................................37
CHAPTER 4 CAUTIONS ......................................................................................38
4.1 Cautions on Flash Self Programming Function .......................................................................38
4.2 Cautions on Non-Map Break ......................................................................................................38
4.3 Cautions on DBTRAP Instruction ..............................................................................................38
4.4 PSC Register Access ..................................................................................................................38
4.5 Cautions on DBPC, DBPSW, and ECR Registers..................................................................... 39
4.6 Cautions on Trace Display Sequence .......................................................................................39
4.7 Cautions on Extension Probe ....................................................................................................39
4.8 Simultaneously Executing Two Instructions When Hardware Break Is Set..........................39

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 8/57
4.9 Cautions on On-Chip Debug Function ......................................................................................42
4.10 Cautions on Standby Mode ......................................................................................................42
4.11 Operation During Break ............................................................................................................42
4.12 Cautions on RAM Hold Voltage Flag .......................................................................................42
4.13 Cautions on Current Consumption..........................................................................................42
4.14 Cautions on ROM Correction Function...................................................................................42
4.15 Cautions on Starting Debugger ...............................................................................................43
CHAPTER 5 NOTES ON TARGET SYSTEM DESIGN ........................................44
CHAPTER 6 OPTIONAL FUNCTIONS................................................................45
6.1 Memory Emulation Function ......................................................................................................46
6.1.1 Functional outline................................................................................................................................... 46
6.1.2 Differences from hardware specifications .............................................................................................. 46
6.2 Coverage Measurement Function..............................................................................................47
6.2.1 Functional outline................................................................................................................................... 47
6.2.2 Differences from hardware specifications .............................................................................................. 47
6.3 TimeMachine Function................................................................................................................48
6.4 Changes to Top Side of Product Consequent to Addition of Optional Functions ............... 48
6.5 How to Add Optional Functions.................................................................................................49
APPENDIX A CHARACTERISTICS OF TARGET INTERFACE .......................50
APPENDIX B REVISION HISTORY ....................................................................57

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 9/57
CHAPTER 1 GENERAL
The QB-V850ESFJ3 is an in-circuit emulator for emulating the V850ES/FE3, V850ES/FF3, V850ES/FG3, or
V850ES/FJ3.
Hardware and software can be debugged efficiently in the development of systems in which the V850ES/FE3,
V850ES/FF3, V850ES/FG3, or V850ES/FJ3 is used. This manual descries basic setup procedures, hardware
specifications, system specifications, and how to set switches.

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 10/57
1.1 Hardware Specifications
Table 1-1. QB-V850ESFJ3 Hardware Specifications
Parameter Specification
Target device V850ES/FE3, V850ES/FF3, V850ES/FG3, V850ES/FJ3
Target system interface voltageNote VDD = EVDD =BVDD,AVREF0
VSS = EVSS = BVSS = AVSS = 0 V
VDD = EVDD = BVDD 3.5 to 5.5 V
AVREF0 4.0 to 5.5 V
Maximum operating frequency 48 MHz
Operating temperature range 0 to 40°C (No condensation)
Storage temperature range −15 to 60°C (No condensation)
External dimensions See Figure 1-1.
AC adapter 15 V, 1 A
Power
consumption Target system power supply Same level or lower than target device (except for the case in standby mode)
Weight 382 g
Host interface USB interface (1.1, 2.0)
Note BVDD and BVSS are not available in the V850ES/FE3 and V850ES/FF3.
Figure 1-1. External Dimensions
Notes 1. Does not include projection of power switch
2. Includes projection of screw that fixes rear spacer
3. Front spacer can vary from 30 mm (longest) to 0 mm (shortest).
4. Front spacer can vary from 20 mm (longest) to 5 mm (shortest).
68 mmNote 3
104 mmNote 2
112.7 mmNote 1
Rear spacer
Front spacerNote 4

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 11/57
1.2 System Specifications
This section shows the QB-V850ESFJ3 system specifications.
Table 1-2. QB-V850ESFJ3 System Specifications (When IS850QB Is Used)
Parameter Specification
Internal ROM 1 MB max.
Internal RAM 60 KB max.
Emulation
memory capacity
External memory 16 MB max. (optionalNote) (mapping possible in 1 MB units)
Real-time execution function Go, Start from Here, Go & Go, Come Here, Restart, Return Out
Program execution
functions Non-real-time execution function Step In, Next Over, Slowmotion
Hardware break Execution: 10 points
Access: 6 points
Software break 2000 points
Fail-safe break Non-map, I/O illegal, write protect
Break functions
Other Trace full break, forced break, timer overflow break
Trace data types Branch-source PC, branch-destination PC, all PCs, all execution data,
access data, access address, R/W status, time stamp, DMA point
(start/end)
Trace modes Real-time trace, Complete trace
Trace events Delay trigger, section, qualify
Trace functions
Memory capacity 256K frames
Real-time RAM monitoring function 256 bytes ×8 points
Measurement clock Measurement-dedicated clock or CPU clock
Measurement objects Beginning through end of program execution
Start event through end event
Maximum measurement time Approximately 195 hours (When using measurement-dedicated clock)
Minimum resolution 20 ns
Number of timers for measurement 8
Measurement results Execution time (Start through end of execution)
Maximum, minimum, average, pass count (between events)
Time
measurement
functions
Other Timer overflow break function (1 point)
TimeMachineTM function (optionalNote) Consult a GHS tool distributor.
Coverage function (optionalNote 1) Detection of execution or pass
Measured range Internal ROM space + arbitrary 1 MB space
Other functions Mapping function, event function, register manipulation function,
memory manipulation function
Note See CHAPTER 6 OPTIONAL FUNCTIONS.
Caution Some functions are not supported depending on the debugger.

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 12/57
1.3 System Configuration
There are two configuration types: S Type and T Type.
This section shows each system configuration when using the QB-V850ESFJ3 connected to a PC (PC-9821
series or PC/ATTM compatible). Connection is possible even without optional products.
Connectors <9> to <13> differ depending on the target device to be emulated.
Figure 1-2. System Configuration (S Type)
<1> Host machine: PC-9821 series, IBM PC/AT compatible can be used
<2> ID850QB Disk/Accessory DiskNote 1: Debugger, USB drivers, manual, etc.
<3> USB interface cable: Cable used for connecting QB-V850ESFJ3 to host machine
<4> AC adapter: Can support 100 to 240 V by replacing AC plug
<5> QB-V850ESFJ3: This product
<6> Check pin adapter (optional)Note 2: Adapter used for monitoring waveforms with oscilloscope
<7> Extension probe flexible type (under development) (optional)
<8> Extension probe coaxial type (optional)
<9> Exchange adapter: Adapter that performs pin conversion
<10> Check pin adapter (optional)Note 3: Adapter used for monitoring waveforms with oscilloscope
<11> Space adapter (optional): Adapter used for height adjustment
<12> Mount adapter (optional): Adapter used for mounting target device
<13> Target connector: Connector to be soldered to target system
<14> Target system
Notes 1. Download the device file from the NEC Electronics website.
URL: http://www.necel.com/micro/index_e.html
2. For the use of this product, refer to [Related Information] on the following webpage.
URL: http://www.necel.com/micro/english/iecube/index.html
3. If both <10> and <11> are used, connection sequence of <10> and <11> may be reversed. In addition,
<8> is required when using <10>.
<1>
<2>
<3>
<4>
<5>
<6>
<7>
<8>
<9>
<11>
<12>
<13> <14>
: Products enclosed by broken lines are optional.
<10>

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 13/57
Figure 1-3. System Configuration (T Type)
<1> Host machine: PC-9821 series, IBM PC/AT compatible can be used
<2> ID850QB Disk/Accessory DiskNote 1: Debugger, USB drivers, manual, etc.
<3> USB interface cable: Cable used for connecting QB-V850ESFJ3 to host machine
<4> AC adapter: Can support 100 to 240 V by replacing AC plug
<5> QB-V850ESFJ3: This product
<6> Check pin adapter (optional)Note 2: Adapter used for monitoring waveforms with oscilloscope
<7> Extension probe flexible type (under development) (optional)
<8> Extension probe coaxial type (optional)
<9> Exchange adapter: Adapter that performs pin conversion
<10> Space adapter (optional): Adapter used for height adjustment
<11> Mount adapter (optional): Adapter used for mounting target device
<12> YQ connector: Connector used for connecting emulator
<13> Target connector: Connector to be soldered to target system
<14> Target system
Notes 1. Download the device file from the NEC Electronics website.
URL: http://www.necel.com/micro/index_e.html
2. For the use of this product, refer to [Related Information] on the following webpage.
URL: http://www.necel.com/micro/english/iecube/index.html
: Products enclosed by broken lines are optional.
<1>
<2>
<3>
<4>
<5>
<6>
<7>
<8>
<14>
<9>
<10> <11>
<13>
<12>

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 14/57
Table 1-3. List of Probe/Connector for Each Target Device (S Type)
Target Device to Be Emulated
No. Name V850ES/FE3
(64-Pin GB)
V850ES/FF3
(80-Pin GK)
V850ES/FG3
(100-Pin GC)
V850ES/FJ3
(144-Pin GJ)
<6> Check pin adapter QB-144-CA-01
(sold separately)
<7> Extension probe
(flexible type)
Under development
(sold separately)
<8> Extension probe
(coaxial type)
QB-144-EP-01S
(sold separately)
<9> Exchange adapter QB-64GB-EA-01S
(sold separately)Note
QB-80GK-EA-02S
(sold separately)Note
QB-100GC-EA-01S
(sold separately)Note
QB-144GJ-EA-03S
(sold separately)Note
<10> Check pin adapter QB-64-CA-01S
(sold separately)Note
QB-80-CA-01S
(sold separately)Note
QB-100-CA-01S
(sold separately)Note
QB-144-CA-01S
(sold separately)Note
<11> Space adapter QB-64-SA-01S
(sold separately)Note
QB-80-SA-01S
(sold separately)Note
QB-100-SA-01S
(sold separately)Note
QB-144-SA-01S
(sold separately)Note
<12> Mount adapter QB-64GB-MA-01S
(sold separately)Note
QB-80GK-MA-01S
(sold separately)Note
QB-100GC-MA-01S
(sold separately)Note
QB-144GJ-MA-01S
(sold separately)Note
<13> Target connector QB-64GB-TC-01S
(sold separately)Note
QB-80GK-TC-01S
(sold separately)Note
QB-100GC-TC-01S
(sold separately)Note
QB-144GJ-TC-01S
(sold separately)Note
(See Note on the next page.)
Table 1-4. List of Probe/Connector for Each Target Device (T Type)
Target Device to Be Emulated
No. Name V850ES/FE3
(64-Pin GB)
V850ES/FF3
(80-Pin GK)
V850ES/FG3
(100-Pin GC)
V850ES/FJ3
(144-Pin GJ)
<6> Check pin adapter QB-144-CA-01
(sold separately)
<7> Extension probe
(flexible type)
QB-144-EP-01S
(sold separately)
<8> Extension probe
(coaxial type)
Under development
(sold separately)
<9> Exchange adapter QB-64GB-EA-02T
(sold separately)Note
QB-80GK-EA-02T
(sold separately)Note
QB-100GC-EA-01T
(sold separately)Note
QB-144GJ-EA-03T
(sold separately)Note
<10> Space adapter QB-64-YS-01T
(sold separately)Note
QB-80-YS-01T
(sold separately)Note
QB-100-YS-01T
(sold separately)Note
QB-144-YS-01T
(sold separately)Note
<11> Mount adapter QB-64GB-HS-01T
(sold separately)Note
QB-80GK-HQ-01T
(sold separately)Note
QB-100GC-HQ-01T
(sold separately)Note
QB-144GJ-HQ-01T
(sold separately)Note
<12> YQ connector QB-64GB-YQ-01T
(sold separately)Note
QB-80GK-YQ-01T
(sold separately)Note
QB-100GC-YQ-01T
(sold separately)Note
QB-144GJ-YQ-01T
(sold separately)Note
<13> Target connector QB-64GB-NQ-01T
(sold separately)Note
QB-80GK-NQ-01T
(sold separately)Note
QB-100GC-NQ-01T
(sold separately)Note
QB-144GJ-NQ-01T
(sold separately)Note
(See Note on the next page.)

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 15/57
Note These accessories are supplied according to the part number ordered.
•If QB-V850ESFJ3-ZZZ is ordered
The exchange adapter and target connector are not supplied.
•If QB-V850ESFJ3-S64GB is ordered
The QB-64GB-EA-01S and QB-64GB-TC-01S are supplied.
•If QB-V850ESFJ3-T64GB is ordered
The QB-64GB-EA-02T, QB-64GB-YQ-01T, and QB-64GB-NQ-01T are supplied.
•If QB-V850ESFJ3-S80GK is ordered
The QB-80GK-EA-02S and QB-80GK-TC-01S are supplied.
•If QB-V850ESFJ3-T80GK is ordered
The QB-80GK-EA-02T, QB-80GK-YQ-01T, and QB-80GK-NQ-01T are supplied.
•If QB-V850ESFJ3-S100GC is ordered
The QB-100GC-EA-01S and QB-100GC-TC-01S are supplied.
•If QB-V850ESFJ3-T100GC is ordered
The QB-100GC-EA-01T, QB-100GC-YQ-01T, and QB-100GC-NQ-01T are supplied.
•If QB-V850ESFJ3-S144GJ is ordered
The QB-144GJ-EA-03S and QB-144GJ-TC-01S are supplied.
•If QB-V850ESFJ3-T144GJ is ordered
The QB-144GJ-EA-03T, QB-144GJ-YQ-01T, and QB-144GJ-NQ-01T are supplied.
Remark For notes on target system design and package drawings, refer to [Related Information] on the
following webpage.
URL: http://www.necel.com/micro/english/iecube/index.html

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 16/57
1.4 Package Contents
The following items have been placed in the QB-V850ESFJ3 packing box. Please check the contents.
Products supplied with QB-V850ESFJ3-ZZZ
<1>: QB-V850ESFJ3
<2>: AC adapter
<3>: USB interface cable
<4>: ID850QB Disk (CD-ROM)
<5>: Accessory Disk (CD-ROM)
<6>: IECUBE Setup Manual (J/E)
<7>: User registration (Guarantee card and software contract in one)
<8>: PG-FPL (Flash Pro Lite)
<9>: Probe holder
<10>: Parts board (for clock)
Products supplied with QB-V850ESFJ3-S64GB
(Order with which S-type connectors for the V850ES/FE3 are included)
<1> to <10>
<11>: Exchange adapter QB-64GB-EA-01S
<12>: Target connector QB-64GB-TC-01S
Products supplied with QB-V850ESFJ3-T64GB
(Order with which T-type connectors for the V850ES/FE3 are included)
<1> to <10>
<11>: Exchange adapter QB-64GB-EA-02T
<12>: Target connector QB-64GB-NQ-01T
<13>: YQ connector QB-64GB-YQ-01T
Products supplied with QB-V850ESFJ3-S80GK
(Order with which S-type connectors for the V850ES/FF3 are included)
<1> to <10>
<11>: Exchange adapter QB-80GK-EA-02S
<12>: Target connector QB-80GK-TC-01S
Products supplied with QB-V850ESFJ3-T80GK
(Order with which T-type connectors for the V850ES/FF3 are included)
<1> to <10>
<11>: Exchange adapter QB-80GK-EA-02T
<12>: Target connector QB-80GK-NQ-01T
<13>: YQ connector QB-80GK-YQ-01T

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 17/57
Products supplied with QB-V850ESFJ3-S100GC
(Order with which S-type connectors for the V850ES/FG3 are included)
<1> to <10>
<11>: Exchange adapter QB-100GC-EA-01S
<12>: Target connector QB-100GC-TC-01S
Products supplied with QB-V850ESFJ3-T100GC
(Order with which T-type connectors for the V850ES/FG3 are included)
<1> to <10>
<11>: Exchange adapter QB-100GC-EA-01T
<12>: Target connector QB-100GC-NQ-01T
<13>: YQ connector QB-100GC-YQ-01T
Products supplied with QB-V850ESFJ3-S144GJ
(Order with which S-type connectors for the V850ES/FJ3 are included)
<1> to <10>
<11>: Exchange adapter QB-144GJ-EA-03S
<12>: Target connector QB-144GJ-TC-01S
Products supplied with QB-V850ESFJ3-T144GJ
(Order with which T-type connectors for the V850ES/FJ3 are included)
<1> to <10>
<11>: Exchange adapter QB-144GJ-EA-03T
<12>: Target connector QB-144GJ-NQ-01T
<13>: YQ connector QB-144GJ-YQ-01T

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 18/57
CHAPTER 2 SETUP PROCEDURE
This chapter explains the QB-V850ESFJ3 setup procedure.
Setup can be completed by performing installation/setup in the order in which it appears in this chapter.
Perform setup along the lines of the following procedure.
See 2.1 Names and Functions of Hardware for jumper and clock board positions.
Main clock settings
At shipment, a 6 MHz resonator is mounted.
If the 6 MHz resonator is used as is, the setting does not have to be changed.
If the clock must be changed, see 2.2 Removal of Acrylic Board and 2.3 Clock Settings.
Sub clock settings
Software settings
See 2.4 Software Settings.
Mounting and connecting connectors
When using the S Type, see 2.5 Mounting and Connecting Connectors (When Using S Type).
When using the T Type, see 2.6 Mounting and Connecting Connectors (When Using T Type).
Connecting USB interface cable and AC adapter
See 2.8 Connecting USB Interface Cable and AC Adapter.
Switching power on and off
See 2.9 Switching Power On and Off
Connecting QB-V850ESFJ3 to target system
See 2.7 Connecting QB-V850ESFJ3 to Target System.
•When not using the extension probe (QB-144-EP-01S): see 2.7.1.
•When using the extension probe (QB-144-EP-01S): see 2.7.2.
At shipment, the QB-V850ESFJ3’s 32.768 kHz resonator is selected.
If modification is necessary, see 2.3.4 Overview of subclock settings.

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 19/57
2.1 Names and Functions of Hardware
Figure 2-1. Names of Parts of QB-V850ESFJ3
(1) CN1, CN2, CN3
These connectors are used to connect the exchange adapter or extension probe.
(2) Parts board connector (for clock)
This parts board is used to mount the resonator.
(For details, refer to 2.3 Clock Settings.)
(3) JP1
This jumper is used for delivery inspection.
All the pins of this jumper are open at shipment. Other settings are prohibited.
(4) JP2
This jumper is used to set the subclock.
1 and 2 are shorted, and 3 and 4 are shorted at shipment.
(For details, refer to 2.3 Clock Settings.)
(5) CN8
This jumper is used for delivery inspection.
All the pins of this jumper are open at shipment. Other settings are prohibited.
Top View Bottom View
Power switch
POWER TARGET CN3 CN2 CN1 Connector for parts board
OSC1
CN8
JP2
Pin 1
JP1

QB-V850ESFJ3 Preliminary User’s Manual ZUD-CD-05-0149 20/57
(6) POWER (Red LED)
This is an LED that shows whether or not the power supply of the QB-V850ESFJ3 is switched on.
LED State QB-V850ESFJ3 State
Lit Power switch ON
Not lit Power switch OFF or AC adapter not connected to QB-V850ESFJ3
Blinking Internal error occurred (Contact an NEC Electronics sales representative or distributor)
(7) TARGET (Green LED)
This is an LED that shows whether or not the power supply of the target system is switched on.
LED State Target System State
Lit Target system power supply ON
Not lit Target system power supply OFF or target system not connected
(8) Power switch
This is the power switch of the QB-V850ESFJ3. It is OFF at shipment.
2.2 Removal of Acrylic Board
To change the jumper or clock setting, the acrylic board on the bottom of the QB-V850ESFJ3 must be removed.
The acrylic board can be removed by lifting it up.
Figure 2-2. Acrylic Board Removal Method