NEC N8146-28 User manual

1
N8146-28 タワーモデル用防塵キット(センサ付)
ユーザーズガイド
はじめに
このたびは、本製品をお買い求めいただき、まことにありがとうございます。
本書は、本製品を正しく安全に設置・使用するための手引きです。本製品をご使用になる前に本書をよく
お読みになり、製品の取り扱いを十分にご理解ください。
必要なときすぐに参照できるよう、お手元に置いておくようにしてください。
ご使用の前に「使用上のご注意」を必ずお読みください。
使用上のご注意 - 必ずお読みください -
本製品を安全に正しくご使用になるために必要な情報が記載されています。
本書では、本製品を安全に正しくお使いいただき、お客様への危害や財産への損害を未然に防止するために、
次の絵表示を使用しています。内容をよく理解されてから、本文をお読みください。
本書では、危険の程度を表す用語として、「警告」と「注意」を使用しています。それぞれの用語は次のような
意味を持つものとして定義されています。
危険に対する注意・表示は次の2種類の記号を使用しています。それぞれの記号は次のような意味を持つもの
として定義されています。
注意の喚起
行為の禁止
行為の強制
本体装置の電源プラグをコンセントから抜い
てください。火災や感電のおそれがあります。
特定しない一般的な禁止を示します。
特定しない一般的な注意・警告を示します。 発煙や発火のおそれがあることを示しま
す。
警告 人が死亡する、または重傷を負うおそれがあることを示しています。
注意 火傷や怪我または物的損害を負うおそれがあることを示しています。
注意の喚起 この記号は危険が発生するおそれがあることを表しています。記号の
中の絵表示は危険の内容を図案化したものです。
(例)
(高温注意)
行為の禁止 この記号は行為の禁止を表しています。記号の中や近くの絵表示は禁
止された行為の内容を図案化したものです。
(例)
(分解禁止)
安全にかかわる表示について
*856-129731-404-00T*
*
856
-
12
9731
-
404
-
00 *

2
安全にお使いいただくために、次に示す注意事項をお守りください。
警告
万一、煙、異臭、異音などが生じた場合は、ただちに電源をOFFにして電源プラグをコンセント
から抜いてください。その後、お買い求めの販売店または保守サービス会社にご連絡ください。
そのまま使用すると火災の原因となります。
注意
本製品を本体装置へ取り付け、取り外しの際は必ず電源プラグをコンセントから抜き、外部装置と
接続しているケーブルを外してください。故障や感電する恐れがあります。
本体装置内部に手をいれるときには、指をはさんだり、ぶつけたりしないように注意してください。
次に示すような場所や本書で指定している環境条件を超える場所には設置・保管しないでくださ
い。火災や故障の原因となるおそれがあります。
● 薬品や化学物質などを扱う場所
● 直射日光が当たる場所
● 湿気の多い場所
● 急激な温度変化のある場所
● 振動や衝撃のある場所
● 腐食性ガス(二酸化硫黄、硫化水素、二酸化窒素、塩素、アンモニア、オゾンなど)の存在する環境
● 腐食を促進する成分(塩化ナトリウムや硫黄など)や導電性の金属などが含まれている環境
本製品を正しく動作させるために次に示す注意事項をお守りください。これらの注意を無視した取り扱いを
すると故障の原因になります。
● 本製品を重ね置きしないでください。
● 保管や取り付け・取り外しの際に固いものにぶつけないでください。
● 梱包状態でも落下させないでください。損傷するおそれがあります。
<本書の記号について>
本書の中には次の記号を使用しています。記号は次のような意味をもつものとして定義されています。
取り扱いで、守らなければいけないことや特に注意すべき点を示します。
取り扱い上のご注意 - 本製品を正しく動作させるために -
安全上のご注意

3
本製品を第三者に譲渡(または売却)するときは、必ず本書を含め全ての添付品を一緒にお渡しください。
本製品の廃棄については各自治体の廃棄ルールに従ってください。詳しくは、各自治体へお問い合わせ
ください。防塵フィルタはプラスチックとして廃棄してください。
廃棄について
第三者への譲渡について

4
1.本製品使用上のご注意
●本製品は Express5800/T110d、T120d 専用オプションです。
●本製品は 塵埃侵入防止にのみ効果が有ります。塩害、腐食性ガスには効果が有りません。
2.構成品
構成品を確認してください。
項番 品名 数量 概要
1防塵カバー 1
2防塵ドア 1
3防塵フィルタ 1項番 1に取り付け済み
4目詰まり検出センサ 1
5目詰まり検出センサ取り付けネジ 2
6センサ接続用ケーブル 1
7目詰まり検出ソフトウェア(CD-ROM)1
8ユーザーズガイド 1本書
防塵ドア
②①
防塵カバー
防塵フィルタ
③
⑧
ユーザーズガイド
④
目詰まり検出センサ
目詰まり検出センサ取り付けネジ
⑤
目詰まり検出ソフトウェア
(
CD
-
ROM
)
⑦
センサ接続用ケーブル
⑥

5
3.装置への取り付け・取り外し
下記の手順にて装置に取り付けを行ってください。
● 取り付ける装置の説明書を参照し、「安全上のご注意」、「取り扱い上のご注意」を守って
取り付け・取り外しを行ってください。
※本製品をT110d、T120dに取り付けることにより、本体外形寸法が以下となります。
200.0 mm (幅) X 613.5 mm (奥行き) X 438.0 mm (高さ) (突起物含まず)
1. フロントベゼルを開いて、上方向にスライドさせ、
取り外してください。
2. デバイスドアを開いて、上方向に
スライドさせ取り外してください。
3. 前項のデバイスドアの取り外しと
逆の手順で防塵ドアを取り付けます。
①
②
防塵ドア
①
②
デバイスドア
②
①
フロントベゼル

6
4. アクセントカバーのツメ2箇所を押してフロントベゼルから外します。
5. 目詰まりセンサケーブルのコネクタをマザーボードの接続コネクタに接続します。
矢印の方向にツメを押して
アクセントカバーを外す。
①
①②
アクセントカバー
目詰まりセンサ
接続用コネクタ
目詰まりセンサ
接続用コネクタ

7
6. 下図の通り、目詰まりセンサケーブルを取り付けてください。
7. フロントベゼルに目詰まりセンサを取り付けネジ(2個)で取り付けてください。
フロントベゼル
裏面
ネジ
止
め
(
2
カ
所
)
フロントパネル上面
フロントパネルの上面を通して正面に出す。
サブベゼルを取り外し、ケーブルを取り付ける。
○印の4カ所でケーブルを固定する。
サブベゼルを取り付ける。

8
8. フロントベゼルを筐体に取り付けてください。
ヒンジの先端を筺体の穴に差し込みます。(3箇所)
①
①
②
フロントベゼル正面にケーブルを出す。

9
9. 目詰まりセンサにケーブルを接続してください。
10. アクセントカバーの取り外しと逆の手順で防塵カバーをフロントベゼルに
取り付けてください。
防塵カバー
②
①

10
4.防塵フィルタの交換
防塵フィルタの推奨使用期間は6か月、最大使用可能期間は1年となっております。
上記期間は使用環境により前後いたします。交換用防塵フィルタはN8147-24を使用してください。
●フィルタを交換しないまま最大使用期間を超えて装置を稼働させた場合、
ほこりの目詰まり等によりデバイスの温度が上昇し装置が故障する原因となります。
1.防塵カバーの『PUSH』文字部分を下に押して、防塵カバーを外してください。
①
②
防塵カバー

11
2.防塵フィルタの交換
2.1 防塵カバーの内側にセットされている防塵フィルタを外してください。
2.2 取り外しと逆の手順で防塵フィルタのタブが手前側になるように防塵カバーに
セットしてください。
3.防塵カバーをフロントベゼルに取り付けます。
5.ソフトウェアのインストール
目詰まり検出ソフトウェアのインストール手順については、添付CD-ROMの
FilterMonitorSoftware(Windows) フォルダ内の“目詰まり検出ソフトウエア(Windows)操作説明書.pdf”
または
FilterMonitorSoftware(Linux) フォルダ内の“目詰まり検出ソフトウエア(Linux)操作説明書.pdf”
をご確認ください。
●Linux OSでご使用の場合、EXPRESSBUILDER Version 6.10-022.01に入っている
ESMPRO/ServerAgentは、防塵センサ機能をサポートしておりませんので、弊社Webサイト
から最新版をダウンロードしてご使用ください。
(http://www.express.nec.co.jp/linux/dload/esmpro/index.html)
タブを持ってフィルタを外してください
防塵フィルタ
防塵カバー
①
②

12
ご注意
(1) 本書の内容の一部または全部を無断で転載することは固くお断りします。
(2) 本書の内容について、将来予告なしに変更することがあります。
(3) 弊社の許可なく複製・改変などを行うことはできません。
(4) 本書の内容については、万全を期して作成しておりますが、万一ご不審な点や誤り、記載もれなど
お気づきの点がございましたら、お買い求めの販売店にご連絡ください。
(5) 本製品を運用した結果の影響については(4)項にかかわらず、いかなる責任も負いかねますので
ご了承ください。
本書は再生紙を使用しています。
タワーモデル用防塵キット(センサ付)ユーザーズガイド
856-129731-404-00 第1版
*856-129731-404-00T*
*
856
-
12
9731
-
404
-
00 *

13
N8146-28 Dust Proof Kit with Sensor for
Tower-model Server User's Guide
Preface
Thank you very much for your purchase of this product.
The guide is intended to allow you to install and use the product correctly and safely. Read the guide carefully
before handling the product.
Keep this User's Guide at hand for quick reference at anytime necessary.
Be sure to read "Safety Precautions" before handling this product.
Precautions for Use (Be Sure to Read)
The following provides information required to use the product safely and properly.
To prevent personal injury and/or property damage from occurring, symbols as shown below are used in this
manual to draw user's attention. Fully understand the meaning of symbols before reading this manual.
In this User's Guide, WARNING or CAUTION is used to indicate a degree of danger. These terms are defined
as follows:
Precautions and notices against hazards are presented with one of the following two symbols. The individual
symbols are defined as follows:
Attentions
Prohibited Actions
Mandatory Actions
Unplug the power cord of the server. Otherwise,
an electric shock or fire may be caused.
Indicates a general prohibited action that
cannot be specifically identified.
Indicates a general notice or warning that
cannot be specifically identified. Indicates there is a risk of fire or fumes.
WARNING Indicates there is a risk of death or serious personal injury.
CAUTION Indicates there is a risk of burns, other personal injury, or property damage.
Attentions This symbol indicates the presence of a hazard if the instruction
is ignored. An image in the symbol illustrates the hazard type.
(Example)
(Hot surface)
Prohibited
Actions This symbol indicates prohibited actions. An image in the symbol
illustrates a particular prohibited action.
(Example)
(Do not disassemble)
Safety Indications
*856-129731-404-00T*
*
856
-
12
9731
-
404
-
00 *

14
Observe the following notes to use the product safely.
WARNING
If smoke, odor, or noise is present, immediately turn off the server and disconnect the power plug
from the outlet, then contact the store where you purchased the product or your maintenance service
company. Using the server in such conditions may cause a fire.
CAUTION
Prior to installing or removing an option, make sure to unplug all system AC power cords from their
electrical outlets. Remove all cables connecting the system with external devices. Failure to
disconnect the power cords before opening the system can result in personal injury and equipment
damage.
Note sufficiently that your fingers may not be caught or cut by a mechanical part at inside of server.
Do not install or store the server in the following places or any place that does not satisfy the
environmental conditions specified in this manual. Failure to follow this instruction may cause a fire
or malfunction of the server.
●Places near chemicals or chemical substances
●Places exposed to direct sunlight
●Places where the air includes much humidity
●Places with drastic changes in temperature
●Places where vibration or impact may be generated
●Places with corrosive gas (sulfur dioxide, hydrogen sulfide, nitrogen dioxide, chlorine, ammonia,
ozone, etc.) in presence
●Places where the air includes components accelerating corrosion (ex. sulfur, sodium chloride) or
conductive metals.
Be sure to observe the following precautions for the proper functioning of the product. Ignoring the precautions
may cause server malfunction or failure.
●Do not pile up the products.
●Pay attention not to hit the product against a solid object during installation, removal, or storage.
●Do not drop the product even when it is packaged. Doing so may cause damage to the product.
< Notations used in this User's Guide >
The following symbol is used in this document. It has the following meaning.
Indicates items that are mandatory or require attention when using the product.
Handling precautions (for proper operations)
Safety Precautions

15
Make sure to provide all accessories including this manual along with the product to a third party.
Dispose of this product according to all national laws and regulations. Dispose of this product as plastic
garbage.
Disposal
Transfer to Third Party

16
1.Notes on Using the Product
●This product is dedicated to Express5800/T110d and T120d servers.
●This product has an effect only in the prevention from dust invasion.
It has no effect in damage from salt and corrosive gas.
2.Components
Check components according to the list below.
Item No. Name Q'ty Description
1 Dust proof cover 1
2 Dust proof door 1
3 Dust proof filter 1 Installed on Item No. 1
4 Filter Monitoring Sensor 1
5 Screws for fixing Filter Monitoring Sensor 2
6 Sensor Cable 1
7 Filter Monitoring Software (CD-ROM) 1
8 User's Guide 1 This Document
①
Dust proof cover
Dust proof filter
③
Filter Monitoring Software
(CD-ROM)
⑦
Dust proof door
②
Sensor Cable
⑥④
Filter Monitoring Sensor
Screws for fixing Filter Monitoring Sensor
⑤
⑧
User's Guide

17
3.Installing/Removing the Product to the Server
Take the steps below to install the product to the server.
● Read the sections "Safety Precautions" and "Handling precautions" in the User's Guide of the
target server to install or remove the product safely and properly.
Note: The outer dimension of T110d or T120d is as follows after the product is installed.
200.0 mm (width) X 613.5 mm (depth) X 438.0 mm (height) (projection excluded)
1. Open the front bezel, and remove it by sliding it upward.
2. Open the device door, and remove it by sliding it upward.
3. Install the dust proof door in reverse order of removal
procedure of device door (Step 2).
①
②
Device door
②
①
Front bezel
①
②
Dust proof door

18
4. Push claws (2 places) on accent cover, and remove the accent cover from front bezel.
5. Connect the sensor cable to the connector on motherboard.
Connector for
sensor cable
Push claws toward the direction
shown by an arrow in the figure
below to remove the accent cover.
①
①②
Accent cover
Connector for
sensor cable

19
6. Route the sensor cable as shown in the figure below.
7. Install the filter monitoring sensor to the front bezel with two fixing screws.
Rear face of front bezel
Secure with screws
(2 places)
Upper of front panel
Pull the cable out from upper of front panel.
Remove the sub-bezel, and connect the cable.
Clamp a cable in four places of the ○mark.
Install the sub-bezel.

20
8. Install the front bezel to server chassis.
①
②
Pull the cable out to the front of front bezel.
Insert the tip of hinge into the holes on chassis (3 places).
①
Table of contents
Other NEC Network Hardware manuals

NEC
NEC HS3-40 User manual

NEC
NEC N8104-213 User manual

NEC
NEC N8151-46 User manual

NEC
NEC Aspire Series User manual

NEC
NEC P401-TMX4D User manual

NEC
NEC N8151-51A Quick start guide

NEC
NEC SVP SERVER - User manual

NEC
NEC Flash Memory Programmer PG-FP3 User manual

NEC
NEC ipasolink 400 User manual

NEC
NEC NP01LM Series User manual
Popular Network Hardware manuals by other brands

Miranda
Miranda DV-Bridge+ Guide to installation and operation

Digiever
Digiever DS-4100 UHD Series Quick installation guide

Balluff
Balluff BNI IOW-560-W01-K022 Assembly instructions

Panasonic
Panasonic WJ-NV200K Quick reference guide

Avocent
Avocent Cyclades ACS 6000 Installation & administrators guide

JDS Uniphase
JDS Uniphase ValidatorPRO-NT, Cu user guide