Neets UniForm User manual
Installation guide
Neets Control - UniForm
Thank you!
Thank you for including the
Neets Control - UniForm as
part of your user experience
strategy.
For specifications, go to:
www.neets.dk/uniform
Included in the box
2
Front of controller
Buttons
3
1 76 mm
1 94 mm
Mini USB Port
E-paper Display
Buttons
Back of controller
Magnets LAN/PoE
Magnet
Magnet
Terminals
4
GND
I/O 1
I/O 2
I/O 3
RX-1
TX-1
GND
TX-2
TX-3
GND
1Recommended position
165 cm / 65”
145 cm / 57”
The controller is designed to be mounted
onto a wall in a vertical orientation.
We recommend locating the center of the
controller between 145 cm – 165 cm
(57” – 65”) above the floor depending on
the height of your typical users..
5
2Bracket details
Alignment holes –
do not insert screws here
Holes for mounting
directly onto the wall
DK 1,5M electrical box
EU 1-gang electrical box W
A
2
1
A
2
2
WW
W W
A
The controller is designed for mounting
onto either a 1-gang electrical box based
on EU standards or a DK 1,5M (LK FUGA Air
only). It can also be mounted directly onto
the wall without any electrical box.
When using EU or DK electrical boxes,
attach the mounting bracket by using the
dedicated holes and screws for the specific
type of electrical box that you have.
A 1-gang US electrical box mounting
option is available as an accessory.
1 1
6
To mount the controller onto an electrical
box, follow Step 1, which is illustrated on
page 8 (DK) or 9 (EU).
If you are not mounting onto an electrical
box, skip ahead to Step 2 to 5, which are
shown on page 10 .
Before you start, make sure the wall itself
is even to prevent any distortion of the
bracket.
3Mounting the bracket
5
4
3
2
1
7
Mount the bracket onto the electrical box
using the dedicated screws for the type of
electrical box that you have (see page 6).
Remove the bracket again.
Mount the bracket and tighten the screws
into the wall.
Level the bracket on the wall and mark
the center of the bracket holes (W) on
the wall.
Drill and insert wall plugs.
8
Mounting onto a DK 1,5M
electrical box (LK FUGA Air)
Mounting onto an EU
1-gang electrical box
9
Mounting directly onto
the wall.
Cutout in the wall must be
at least 45 x 45 mm
(1,8” x 1,8”)
10
Connect the PoE cable (and terminal
connectors if they are a part of the
installation) from the wall to the
controller.
Powering the Controller
4
From IEEE802.3 compliant
PoE injector or switch
11
Put the controller on top of the bracket.
Make sure the controller is lined up
correctly and ensure that the alignment
holes are free so that all four magnets
are able to connect.
To remove the controller, use both hands
to grasp the controller on each side and
pull it straight out from the wall.
Mounting the Controller on the bracket
5
12
First, connect the controller to your
PC using a USB cable.
Now, using the Neets Project
Designer software, you can
upload a projectfile directly to the
controller.
For more information about Neets
Project Designer, visit:
www.neets.dk/product/neets-
project-designer/
7Uploading a Project File
13
Warning
This equipment should be operated only from the included power supply. To
remove power from the equipment safely, remove all power cords from the
rear of the equipment, or the desktop power module (if detachable), or from
the power source receptacle (wall plug).
Power cords should be routed so that they are not likely to be stepped on or
pinched by items placed upon or against them.
Do not defeat the safety purpose of a polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A ground-
ing-type plug has two blades and a third grounding prong. The wide blade
or the third prong is provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete
outlet. Unplug this apparatus during lightning storms or when unused for
long periods of time.
Refer all servicing to qualified service personnel. There are no user-service-
able parts inside. To prevent the risk of shock, do not attempt to service this
equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards. Contact your local Neets reseller or
distributor.
If the equipment has slots or holes in the enclosure, these are provided to
prevent overheating of sensitive components inside. These openings must
never be blocked by other objects.
Do not use this equipment near water.
To reduce the risk of fire or electric shock, do not expose this apparatus to
rain or moisture and objects filled with liquids.
Unplug the product before cleaning. Clean only with a dry cloth and not
cleaning fluid or aerosols. Such products
could enter the unit and cause damage, fire, or electric shock. Some
substances may also mar the finish of the product.
Caution
Read these instructions. Read and understand all safety and operating
instructions before using the equipment. Keep these Instructions.
The safety instructions should be kept for future reference. Heed all warn-
ings. Follow all warnings and instructions marked on the equipment or in
the user information. Avoid attachments. Do not use tools or attachments
that are not recommended, as they may be hazardous.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
The Class A limits are designed to provide reasonable protection against harm-
ful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference, in which case the user
will be required to correct the interference at his own expense.
FCC regulations state that any unauthorized changes or modifications to this
equipment, not expressly approved by the manufacturer, could void the user’s
authority to operate this equipment.
14
Learn more at neets.dk
Visit our website neets.dk for additional information
about the product and the latest firmware.
Table of contents
