neighbor The Chair User manual

01
The
Chair
Assembly Guide
BOXES NEEDED:
(1)
(1)
The Chair
Chair Cushions

Components Assembly Instructions Contact
02
Parts
1X Left Arm
The Chair Box
1X Large Base
The Chair Box
1X Large Roped Back
The Chair Box
1X Chair Back Support
The Chair Box
1X Right Arm
The Chair Box

Components Assembly Instructions Contact
03
Cushions
The Chair Cushions Box
Hardware
The Chair Frame Box
1X Base Cushion
8X Hex Bolt
2X L-Bracket
8X Screw
2X Arm Cushion
1X Back Cushion
Tools
1X Allen Wrench
The Chair Frame Box
Phillips Head Screwdriver
*Not included

Components Assembly Instructions Contact
04
Assembly Tips
Exercise caution while lifting
Two-person lift is recommended. Both the
boxes and the product itself are large and heavy
and awkward to lift alone.
Lay everything out before you begin
Spreading out all of the components prior to
assembling them will help you find the parts
you are looking for and will make for a faster
and easier assembly process!
Assemble on a soft surface
We recommend assembling your furniture on a
soft surface such as a rug(s) or a towel(s). The wood
frame can scratch easily if accidentally rubbed
against harsh textures like brick or concrete.
Loose first, then tight
Do not fully tighten hex bolts when assembling.
Insert them loosely first. After the modules are
fully assembled, then tighten the bolts firmly.
Differing humidity levels can slightly affect how
the pieces fit together and this strategy should
alleviate that.
Product Care
Caring for teak
Unfinished teak will gradually change color
from a honey gold to a silver-grey patina.
We encourage allowing the teak to turn color
naturally and cleaning it annually or bi-annually.
As for cleaning, we recommend Golden Teak
Cleaner, which is specifically designed to kill
mould and mildew spores inside teak.
Avoid prolonging mildew growth. If left in the
shade for extended periods of time, this can be
common.
Covering your furniture for extended periods of
time, especially if enduring consistent inclement
weather will greatly prolong the lifespan of the
wood.
Caring for cushion cover fabric
One of the best ways to keep your Sunbrella
fabric looking good is to brush off dirt before
it becomes embedded in the fabrics and wipe
up spills or clean soon after a stain occurs. The
quicker you clean spills and stains, the easier
they can be to remove.
When removing stains, typically these are the
steps you should try:
• Blot (don’t rub) liquid spills with a clean, dry
cloth. For oil-based spills, apply an absorbent
such as corn starch, then remove with a
straight edge.
• Spray on a mild cleaning solution of soap
(such as Woolite® or Dawn®) and water.
• Rinse the fabric thoroughly to remove all
soap residue.
• Air dry.
Avoid scrubbing, hard bristle brushes or any
other abrasive cleaning method.
Sunbrella should only be allowed to air dry.
Protect the area around your Sunbrella fabric
when using bleach or other chemical solvents
that may discolor non-Sunbrella fabrics. Always
rinse Sunbrella thoroughly.
Bleach can have harmful effects on the natural
environment around you. Please follow all safety
and environmental precautions according to the
bleach label.
If fabric has some wrinkling, use an iron on the
synthetic setting. As iron temperatures may
vary, first test a small inconspicuous area before
ironing the entire piece.
DO NOT use a steamer or an iron set to the
steam setting.

05 Components Assembly Instructions Contact
Connect large
base and left arm
Place the left arm component on a soft
surface, verifying that the two screw holes
are facing upward. Gently insert the long
base into the left arm’s inner slots.
1

06 Components Assembly Instructions Contact
Connect right arm
to base
Gently insert the right arm by sliding it onto the
large base until its holes are aligned with the
corresponding threaded holes on the base’s.
2

07 Components Assembly Instructions Contact
4x
Fasten arms to
base
Using the Allen wrench provided, fasten the base
to both the left and right arm components with
two bolts. Repeat on all four legs.
3

08 Components Assembly Instructions Contact
Secure roped
back to base
Insert the lower brackets of the chair’s back
component into the slots of its base..
4

09 Components Assembly Instructions Contact
Attach back support
to roped back
Lower the back support component onto the roped
back by fitting brackets into their corresponding
grooves. Align slots underneath back support with
the corresponding roped back’s top brackets. Then
insert bracket into the slot.
5

10 Components Assembly Instructions Contact
2x
Fasten back
support to arms
Aligning the pre-drilled holes on the arm
components with the holes on the L-bracket.
Then, with a Phillips Head screwdriver, gently
secure with four screws. Repeat opposite side.
6

11 Components Assembly Instructions Contact
Add cushions
First with zipper seams facing backward, add
arm cushions to each side. Thread the cushions’
laces around the roped back posts and tie them
down. Then add the base cushion. Finally, add
the back cushion. Relax! You’re ready to enjoy
your chair.
2x
7

Components Assembly Instructions Contact
12
Have a question, comment, feedback?
We love hearing from customers.
[e-mail]
hineighbor.com
Contact