neighbor Haven Chair-and-a-Half User manual

Haven
Chair-and-a-Half
Assembly Guide

Components Assembly Instructions Contact02
Chair-and-a-Half Frame (1)
Cushions - Chair-and-a-Half (1)
Frame Boxes
Cushion Boxes

Components Assembly Instructions Contact03
Parts
1X Chair-and-a-Half Base
Chair-and-a-Half Frame Box
1X Chair-and-a-Half Back Support
Chair-and-a-Half Frame Box
1X Chair-and-a-Half Roped Back
Chair-and-a-Half Frame Box
1X Left Arm
Chair-and-a-Half Frame Box
1X Right Arm
Chair-and-a-Half Frame Box
8X 30mm Hex Bolt
Chair-and-a-Half Frame Box
8X Phillips Head Screw
Chair-and-a-Half Frame Box
2X L-Bracket
Chair-and-a-Half Frame Box
Hardware
To o l s
Allen Wrench
Chair-and-a-Half Frame Box
Phillips Head Screwdriver
*Not included

Components Assembly Instructions Contact04
Cushions
1X Chair-and-a-Half Base Cushion
Chair-and-a-Half Cushions Box
1X Chair-and-a-Half Back Cushion
Chair-and-a-Half Cushions Box
1X Chair-and-a-Half Throw Pillow
Chair-and-a-Half Cushions Box
2X Chair-and-a-Half Arm Cushion
Chair-and-a-Half Cushions Box

Components Assembly Instructions Contact05
Product Care
Caring for teak
Unfinished teak will gradually change color
from honey gold to a silver-gray patina. We
encourage allowing the teak to turn color
naturally and cleaning it annually or bi-annually.
As for cleaning, we recommend Golden Teak
Cleaner, which is specifically designed to kill
mold and mildew spores inside teak.
Avoid prolonging mildew growth. If left in
the shade for extended periods, this can be
common. If you live in a particularly humid
or rainy climate, keep a closer eye on mildew
growth and clean as needed.
Covering your furniture when not in use will
greatly prolong the lifespan of the wood.
Caring for Sunbrella
Brush off dirt before it becomes embedded in
the fabric and wipe up spills as soon as they
happen. Rinse thoroughly and air dry. Avoid
scrubbing, stiff bristle brushes, or any other
abrasive cleaning method.
Protect the area around your furniture when
using bleach or other chemical solvents that
may discolor non-Sunbrella fabrics.
If fabric is wrinkled, use an iron on the synthetic
setting. As iron temperatures may vary, test
a small area first before ironing the entire piece.
Do not use a steamer or an iron set to the
steam setting.
Fabric stain removal
• Blot (don’t rub) liquid spills with a clean, dry
cloth. For oil-based spills, apply an absorbent
such as corn starch then remove with a
straight edge.
• Spray on a mild cleaning solution of soap
(such as Woolite®or Dawn®) and water and
lightly agitate with a sponge or gentle brush.
• Rinse the fabric thoroughly to remove all
soap residue.
• Air dry.
• As needed, unzip and machine-wash covers.
Assembly Tips
Use caution when lifting
Two-person lift is recommended. The boxes
and product are both large and heavy.
Lay everything out before you begin
Getting familiar with all the components before
assembly will make for a faster and easier
assembly process.
Assemble on a soft surface
We recommend assembling your furniture on a
soft surface such as a rug or a towel. The wood
frame can scratch against harsh textures like
brick or concrete.
Loose first, then tight
Partly tighten the hex bolts while assembly. After
the modules are fully assembled, tighten the
bolts firmly. Keep in mind humidity levels can
slightly affect how the pieces fit together.

06 Components Assembly Instructions Contact
Connect base
to left arm
Place the Left Arm on a soft surface with the
two screw holes facing up. Gently insert the
Chair-and-a-Half Base into the arm’s inner slots.
1
Backrest slots should
align with the back of
the armrest, as shown

07 Components Assembly Instructions Contact
Connect right arm
to base
Gently insert the Right Arm by sliding it into the
Chair-and-a-Half Base until its holes are aligned
with the base’s corresponding threaded holes.
2

08 Components Assembly Instructions Contact
Fasten arms
to base
Using the Allen Wrench provided, fasten the
Chair-and-a-Half Base to the Left and Right
Arms with four 30mm Hex Bolts per side.
3
8X 30mm Hex Bolt

09 Components Assembly Instructions Contact
Secure roped
back to base
Insert the Chair-and-a-Half Roped Back into the
slots of the Chair-and-a-Half Base.
4
Drain holes face down

10 Components Assembly Instructions Contact
Attach back support
to roped back
Lower the Chair-and-a-Half Back Support onto
the Chair-and-a-Half Roped Back by fitting the
tabs into their corresponding slots, then insert.
5

11 Components Assembly Instructions Contact
Fasten back
support to arms
Align the holes on the L-Bracket to the
pre-drilled holes on the Left Arm and Chair-
and-a-Half Back Support. With a Phillips
Head Screwdriver, fasten with four Phillips
Head Screws. Repeat on opposite side.
6
8X Phillips Head Screw

12 Components Assembly Instructions Contact
Add cushions
With the zipper seams facing backward, add the
Arm Cushions to each side. Thread the cushions’
laces around the roped back posts and tie them
down. Then, add the Chair-and-a-Half Base
Cushion and finally, the Back Cushion. Relax! You’re
ready to enjoy your chair.
7
3x

Components Assembly Instructions Contact13
Have a question, comment, feedback?
We love hearing from customers.
[e-mail]
hineighbor.com
Contact