Neilsen CT4543 User manual

HOT WIRE FOAM CUTTER CT4543
ORIGINAL INSTRUCTIONS
Cannon Tools Limited
Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
PLEASE READ THIS MANUAL CAREFULLY BEFORE USE

EC DECLARATION OF CONFORMITY
We CANNON TOOLS LTD
20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.
Declare that the following machine complies with the appropriate basic safety and health
requirements of the EC Directive based on its design and type, as brought into circulation by
us.
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity.
Product description: HOT WIRE FOAM CUTTER
Model: CT4543
Applicable EC Directives:
EC Low Voltage Directive 2014/35/EU
Harmonized standards
EN 60335-2-45, EN 60335-1, EN 62233
20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
Mr. Gurcharan Tony Singh Sanghera
Managing Director
CANNON TOOLS LTD
2017-05-10

IMPORTANT SAFETY PRECAUTIONS
1. CAUTION –The tool reaches high temperature! May cause burn.
2. Do not touch hot parts when in use.
3. Keep out of reach of children. This is not a toy and not intended for use by children 8 years
old or younger without adult supervision.
4. Misuse may cause burns, electric shock and injuries.
5. Do not immerse tool in water! Danger of electric shock!
6. Always use the tool on a heatproof and uncluttered table.
7. After finished using the tool, unplug the adapter and let the tool coo naturally on safety
stand in a safe place, out of reach of children
8. Users should always rest a hot tool on the stand to prevent risk of fire.
9. If the cord is damaged, do not use. Cord must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
10. For domestic use only. use only for the intended purposes.
11. This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children unless they are older than 8
and supervised.
12. Keep the appliance and its cord out of reach of children less than 8 years.
OPERATING INSTRUCTIONS
1. Draw the design on the foam. Or cut a pattern, pin to the foam, and make a rough
trace of the pattern, then remove pattern.
2. Choose your tip and insert into handle, ensure position is secured.
3. Check the voltage of the adaptor is the same as source of current, plug in adapter to
wall socket
4. Always try on test object first before commencing your project.
5. Remove large unwanted chucks first for easier handling to prevent breakage.
6. Hold the cutter in a comfortable position and cut the design out of the foam gently. Do
not use force. Let the heat do the work.
mAIN FEATURES
1. Quick heat-up feature allows polystyrene foam cutting almost instantly with the hot-wire tip.
2. Comes with three Quick-Change-Tips allowing users to “pulg-and-use”for a variety of daily
projects: Hot-wire Tip / Hot-knife Tip / Engraving Tip
3. Allows users to make cutouts from center of alphabets without needing to cut though the
alphabet!
WARNING
Never use any other type of wire for replacement! May cause damage to adapter!
Use only our HW-110W replacement wire or use dia. 0.23mm resistance wire.

Technical specification for the adaptor
Input: 100-240V~50/60Hz,
Output: DC 5.0V 2.0A
Wattage:
Hot Wire Tip (HW-110T1): 8.7W
Hot Knife Tip (HW-110T2): 9.6W
Engraver Tip (HW-110T3): 4.2W
Pre-heat Time
Hot Wire Tip (HW-110T1): 30 sec
Hot Knife Tip (HW-110T2): 60 sec
Engraver Tip (HW-110T3): 120 sec
Max Tip Temperature
Hot Wire Tip (HW-110T1): 150℃
Hot Knife Tip (HW-110T2): 200℃
Engraver Tip (HW-110T3): 300℃
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and collection systems or contact
the retailer where the product was purchased. They can take this product for environmental safe
recycling.
CANNON TOOLS LTD
Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.
Made in China