Neox crosser User manual
USER MANUAL
pensata, progettata e prodotta in Italia
NEOX User manual - Edition 01-2015 3
Travelling autonomy of a pedal assisted cycle
The travelling autonomy of the bicycle with the aid of the assisted pedalling PAS,
can vary depending on the dierent conditions of use and the dierent weights
being transported, up to a maximum of 80/100 Km (ECO and NO ASSIST cycle)
according to the model.
For example, a prolonged climb with a gradient of more than 7%, with transported
weight of 100 kg will drastically reduce the autonomy to even 20/25 Km. The elec-
tric motor will absorb more power with increased weight and when climbing hills,
riding against the wind and repetitive stopping and changing gear, thereby redu-
cing the distances that can normally be travelled.
To increase the autonomy, do not use the assisted pedalling on flat or downhill
stretches of road.
IMPORTANT NOTE: The pedal assisted cycle requires “steady” and not “excess-
ive” pedalling. Pedalling quickly, over 70/80 revolutions per minute and with an
appropriate gear ratio, allows the motor to work at maximum eciency and with
minimum power consumption for the same torque delivered.
If the cyclist is skilled at making the motor operate at maximum eciency, this
drastically lowers the electric energy absorption and consequently optimises con-
sumption.
The power consumption level is highlighted on the display. Being able to pedal in
such a way that keeps this string low, leads to optimized and lower consumption.
+
-
NEOX User manual - Edition 01-20154
Electric assisted pedalling
NEOX is equipped with an electric assisted pedalling system. Assistance may be set
to one of 4 positions (Fig. 1):
The adjustment can be carried out at any time and situation of use by pressing the
M button directly on the display (Fig. 01) or via the buttons on the left side of the
handlebars (Fig. 02)
Decrease
assistance
Increase
assistance
01 02
NEOX User manual - Edition 01-2015 5
The Display
1. Power level
2. Batter status
3.
4. Speed
5. Total Km
6. Assistance level set
7. Button for the lights and/or display backlight
8. Estimation of distance in kilometres at that particular moment
9. O button
10. Assistance mode change button
11. UP button
12. DOWN button
13. Enter button
14. Red LED
15. Yellow LED
16.
2
38
5
7
914
15
16
4
10 11 12 13
6
7
1
NEOX User manual - Edition 01-20156
How to turn on your Neox
1. Turn the switch clockwise to the ON position. The three LEDs A - B - C will light up.
2. When the monitor turns on a "0" will appear and 4 lines in the lower right corner.
3. Enter your 4-digit PIN code.
4. Select the number with the arrow buttons, press enter to confirm each number.
5. Each time a number is entered and confirmed the line in the lower right corner be-
comes a "0".
About three seconds after the code has been entered the bike will turn on and by
default go into fourth gear.
The bike is ready for use.
CAUTION: Do not press on the pedals during the start-up phase !!!
O
On
A
B
C
NEOX User manual - Edition 01-2015 7
How to turn o your Neox
Turning Off 1 (sTandard)
In any gear, and in any condition directly turn o the bike with the switch by rotat-
ing the key anti-clockwise to the "O" position. Remove the key.
The last gear used will remain engaged.
Turning Off 2 (prOTecTed wiTh neOx pin anTi-ThefT sysTem)
Press and hold down the o button on the monitor (9) for 3 seconds to activate the
mechanical restraint. Now your Neox is protected and the pedals will rotate freely
to the right and the left without transmitting any motion to the rear wheel.
When the red LED is lit, turn o the system using the switch, putting the key into
the "O" position. Remove the key.
O
On
9
NEOX User manual - Edition 01-20158
How to activate the Neox anti-theft system
The bike has two anti-theft systems.
The first inhibits transmission and can only be reactivated by entering the Neox
Pin code.
The second system consists of the mechanical locking of the rear wheel.
In the first case, see the section "Turning O 2".
LOcking The rear wheeL (if prOvided)
1. With the bike stopped put the key into the switch.
2. Turn it 360 degrees anticlockwise.
3. Slightly move the wheel back and forth a few degrees (A) if you are unable to fully
rotate the key.
4. Remove the key.
Always be sure to unlock the wheel before using the bike !!!
A
NEOX User manual - Edition 01-2015 9
The battery
usefuL infOrmaTiOn abOuT The baTTery
The charging process must be carried out in a ventilated room or in the garage, with
the battery connected to the bicycle or by removing the battery from the bicycle.
Before charging make sure the battery has not been subjected to large fluctuations
in temperature, if so wait 30 minutes before connecting the charger to the battery.
While charging a red light is lit on the battery charger.
When the green light turns on, this means charging is complete (100% charge in
about 5 hours, 80% charge in about 4 hours)
The battery should be fully charged.
It is not recommended to leave the battery uncharged as this may seriously
damage it.
When the battery is uncharged do not to try to use up the little power re-
maining but proceed to recharge it otherwise the battery will be damaged
severely.
Do not leave the battery to charge for more than 12 hours.
Never charge the battery in extremely hot conditions.
Never charge near flammable liquids.
Do not cover the battery and/or charger in any way.
While charging the battery heats up slightly.
Only use the supplied power adapter.
If the vehicle is not used for a long period of time, it is advisable to recharge the
battery every 3 months and to keep it in a dry area at a temperature between 0°C
and 25°C to avoid damaging it.
Ambient temperature during charging: between 0°C and 45°C.
Ambient temperature during normal operation: between -10°C and 45°C.
The battery does not require maintenance, in the event of failure or a significant re-
duction in performance or autonomy contact your Authorised Neox Service Centre.
If the battery emits a bad smell, unplug it from the electrical outlet and contact an
Authorised Neox Service Centre.
The battery undergoes a capacity reduction of 20% after 600-800 cycles.
The exhausted battery (end of life) should not be thrown away with normal waste.
NOTE: The battery performance will vary according to the weight of the rider, the
NEOX User manual - Edition 01-201510
presence or absence of uphill climbs, the conditions of the road surface and the
temperature.
In summer, autonomy is significantly higher than in winter.
For charging see the information leaflet.
Warnings
The first time the battery must be recharged for at least 7 hours.
For the first 5 uses completely charge the battery and then fully discharge it.
This will ensure the maximum performance of the battery pack.
Fully charge the battery before long stops.
Do not store the e-bike for long stops with the battery uncharged.
The Neox battery
The NEOX battery (Fig 1) is a battery pack constructed with Samsung cylindrical
cells.
The lithium-ion batteries have a high energy density and are perfect for cyclic ap-
plications. Compared to traditional lead-acid batteries, lithium-ion batteries have
advantages in terms of savings: up to 70% reduction in volume and weight, while
the number of charging cycles is three times higher.
Another important advantage of the NEOX lithium-ion battery is that it is equipped
with a Battery Management System (BMS) that automatically compensates for any
imbalance between the cells, to ensure maximum safety and durability of the bat-
tery. The NEOX lithium-ion battery is equipped with a cell-battery integrated safety
control system.
Unlike other batteries, lithium-ion batteries have no memory eect and can be
charged even if they are fully discharged.
The total battery capacity is reached after 4.5 complete cycles of charging - dis-
charging. The first time the battery must be recharged for at least 7 hours.
NEOX User manual - Edition 01-2015 11
On/Off and baTTery remOvaL swiTch
Characteristics:
The key can be turned to three positions:
1. “OFF”: with the key in this position power to the
Neox is cut, the motor is o but the battery pack is
locked on the bike.
2. “ON”: the power is on, the motor is running and the
battery pack is locked on the bike.
3. “OPEN”: the motor is o, the battery is unlocked
and can be removed from the bicycle. Keep the key in this position to replace the
battery.
To get to this position, press the key inward before turning it anticlockwise.
remOving The baTTery
Support the battery with your the left hand (fig. 2), so
as to ensure that once the locking system has been
disengaged within the main tube of the frame by ro-
tating the key switch, the battery can not fall to the
ground.
Press the key inward and rotate anticlockwise (fig.1)
until it has been completely rotated to the left.
Pull out the battery by tilting it downwards. (fig.3)
Open
On
O
03
Open
01
02
Push
NEOX User manual - Edition 01-201512
insTaLLing The baTTery
Make sure the switch is in the "open" position and
therefore completely turned anticlockwise.
Take the battery with your left hand as shown. (Fig.1)
Insert the bottom of the battery into its housing inside
the main tube of the frame at an outward angle with
respect to the frame and move it downward (Fig. 2),
making sure that the coupling on the bottom of the
battery box (Part. A) fits properly on the lower edge
of the frame tube (Part. B) as shown. (Fig. 3)
Push the battery upwards until it is firmly inserted so
that it is properly attached to the frame tube. (Fig. 4)
While firmly pushing the battery upwards, (Fig.5) so
that it is properly attached to the frame tube, rotate
the key switch clockwise until it is in a vertical posi-
tion, the OFF position. (Fig. 5 Part. C)
At this point the battery is properly inserted and
locked inside its housing and your Neox is ready for
use.
01
Open
Push
02
A B
03 04 05
C
Open O
NEOX User manual - Edition 01-2015 13
hOw dOes The neOx baTTery perfOrm during use
Above all it is important to remember, as said above, that the Neox battery reaches
its best performance after the first 4/5 full charging and recharging cycles and
when it is recharged for the first time for at least 7 hours.
The intelligent electronic management system of the NEOX battery (BMS) protects
the lithium-ion battery. The BMS controls each single cell, after the first few re-
charges it balances the cells and thereby prolongs the battery life. The interval
between the date of first use and the date on which it will be necessary to replace
your Neox battery is therefore very long.
While using your Neox is important to understand what happens with the gradual
discharge of the battery. In fact the Neox is a fully electronic e-bike, including gear
changes. The system however has been designed so that the user is able to use the
Neox as a normal bike and therefore even with the battery completely discharged,
despite the fact that the gearbox is fully electronic. In fact, with a low battery, there
will be a reserve of energy that will allow the rider to reach their destination while
being able to use the gears despite the fact they are electronically controlled and
the battery is fully depleted
During use, with a fully charged battery, Neox will have more assistance power
available, in all three assistance modes. As the reserve energy in the battery de-
creases, the power available to your Neox will gradually decrease. If we are using
STANDARD mode, then change again to ECO mode until all of the available energy
in the battery has been used before changing to NO ASSIST mode.
At this point, with all the energy used, NEOX becomes a normal bicycle, with full use
of the gears despite the fact they are electronically controlled.
NEOX User manual - Edition 01-201514
charging The baTTery
The NEOX battery can be charged both while installed on the bike (Fig. 1) and when
removed from its housing (Fig. 2) by inserting the charging connector plug into the
front of the battery.
The charging process must be carried out in a ventilated room or garage.
0201
NEOX User manual - Edition 01-2015 15
hOw TO use The baTTery charger
1. Make sure the connections are in good condition and have not been damaged by
excessive force or misuse.
2. Insert the plug (1) of the battery charger into a 220 volt AC outlet. If the plug is in-
serted into the 220 volt AC outlet without the battery connected to the charger,
a green LED will light up, indicating that the unit is on stand-by.
3. Connect the connector (2) to the flat battery; the green light will turn red.
4. The LED light will turn green when the battery is fully charged. When the battery is
fully charged, disconnect charger plugs 1 and 2 and remove the battery.
These instructions are also contained inside the battery charger packaging.
warnings
The first time the battery must be recharged for at least 7 hours.
For the first 5 uses completely charge the battery and then fully discharge it.
This will ensure the maximum performance of the battery pack.
Fully charge the battery before long stops.
Do not store the e-bike for long stops with the battery uncharged.
01
02
NEOX User manual - Edition 01-201516
Gearbox F8.11
Your Neox is equipped with a gearbox that is more similar to that found on a mo-
torcycle/car than a normal bicycle gear system. IT is equipped with an innovative
gearbox, with rotary engagement and with electric controls on the handlebars.
The bike has 4 or 8 sequential speeds available, depending on the model purchased.
-
tionary and/or during movement, without any restriction for the user.
Like all innovations, this system needs to be understood so that you can quickly
take advantage of all the benefits that the system presents.
Below are some advice and tips.
inTrOducTiOn
The Neox gearbox has 4 or 8 speeds available, depending on the model purchased.
Gear 1 (lowest gear)
The pedalling resistance decreases and the speed achieved is lower, but it is easier
to climb hills.
4/8 gear (highest gear):
the resistance to pedalling is increased and the speed achieved is higher.
The gear change is performed by pressing the electric buttons on the right side of
the handlebars. (Fig.1)
The right button increases the gear, the left button decreases the gear.
NEOX User manual - Edition 01-2015 17
change (Or increase in gear)
is the change from one gear to a higher gear, i.e. from gear 1 to 4 or 8, depend-
ing on the model.
This may be carried out in any situation and dynamics of use without any problem,
applying either minimum or maximum pressure on the pedal cranks (added to the
thrust torque of the motor).
The gear change is sequential and has been designed so that it does not require any
special skill by the user.
In fact the user can set o with any gear engaged. When you press the button to
make the change, the system first engages the desired gear, and once this is en-
gaged, disengages the previous gear. This allows an excellent degree of fluidity and
the low noise levels produced by the system are second to none.
cLimb (Or decrease in gear)
is the change from one gear to a lower gear, i.e. from gear 4 or 8, depending
on the model, to gear 1.
As it is an extremely rapid change, the climb must be performed while bearing in
mind some features of the system:
The bike incorporates a SAFETY system that inhibits downward gear changes by
the user while pushing on the pedal. In the event the wrong button is pressed or
the repeated pressing of the button, this system avoids a sudden increase in ped-
alling frequency that could unbalance the user, resulting in danger to themselves
or others.
Therefore, to perform the CLIMB (increase in gear) just REDUCE pressure on the
pedal to a minimum until the sensor measuring the torque transmitted to the pedal
gives consent (via software) to the system to change down a gear.
This system allows you to change up a gear in total safety both for the user and
for your Neox device.
Gear
-
Gear
+
01
NEOX User manual - Edition 01-201518
Resetting or aligning the F8.11 gearbox
The NEOX F8.11 gearbox is equipped with an automatic reset or "alignment" system
which is available to the user, which can be easily operated by means of two but-
tons on the display.
All bicycles on the market may experience problems with their gear system: the
chain falling o, a branch or a stone entering the gear assembly or a gear change
altering the device or simple stretching or stabilizing of the cables.
These problems can be solved by the owner, if they are skilled, or by a qualified
mechanic, equipped with gloves and proper tools.
The Neox transmission system can also suer problems, due to a sudden jump, or
incorrect operation by the user, that alters the alignment of the F8.11 gear system
while not compromising its use.
For the user, it will be very hard to detect any problems during use of intermediate
gears, if not when engaging the highest gear (gear 4 or 8 depending on the model):
Neox does not change to the gear chosen and shown on the display, but remains in
To reset the alignment takes 5 seconds!
Simply press and hold down the two up and down arrow keys on the display sim-
ultaneously for 3-4 seconds, shown in the figure.
The display will show 0 and you will hear the gearbox align.
In other words, Neox has adopted the same procedure for aligning and cleaning
printheads, the same 0 calibration procedure used with precision machine tools.
NEOX User manual - Edition 01-2015 19
OperaTiOn Of The pedaL assisTance mOde.
The pedal assistance mode has 4 levels (including the no assist mode).
To move with the dierent levels the user must make sure that the e-bike is ON.
When you turn on the system, the pedal assistance function is activated at the
whenever the bike is turned o and then on again.
In "No Assist" mode the energy supplied is 0, therefore the bike only moves forward
with the force that the user applies to the crank arms.
In “Eco” mode the energy supplied by the battery is minimal. This feature provides
greater autonomy with a lower level of assistance.
In “Standard” mode the pedal assistance is at the intermediate level.
(where 1 is the force of the user and 2 the force of the motor) and, consequently,
the travelling range will be considerably lower.
During a journey, an adequate selection of the assistance mode level, according to
the terrain or pedalling conditions, will provide an optimum relationship between
the economy of the battery and the ease of pedalling.
2
38
5
7
914
15
16
4
10 11 12 13
6
7
1
Decrease
Assistance
Increase
Assistance
02
01
SIRAL SRL
Località Fornace 13 z.a. - 36076 Recoaro Terme Vi Italy
Tel +39 0445 780795/+39 0445 780290 - Fax +39 0445 792508
www.myneox.it - info@siral.it
www.tecladesign.it
Other manuals for crosser
1
This manual suits for next models
3
Table of contents
Other Neox Bicycle manuals
