NetComm 3G10WVR User manual

YML10WVR HSPA WiFi Router with Voice-User Guide
www.netcommlimited.com 1
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice
User Guide
3G10WVR

HSPA WiFi Router with Voice-User Guide YML10WVR
2 www.netcommlimited.com
Preface
The purpose of this manual is to provide you with detailed information on the installation, operation and application of your HSPA WiFi
Router with Voice.
Important Notice and Safety Precaution
• Before servicing or disassembling this equipment, always disconnect all power or telephone lines from the device.
• Use an appropriate power supply, preferably the supplied power adapter, with an output of DC 12V 1.5A
• Donotoperatethedevicenearammablegasorfumes.Turnoffthedevicewhenyouarenearapetrolstation,fueldepotor
chemical plant/depot. Operation of such equipment in potentially explosive atmospheres can represent a safety hazard.
• The device and antenna shall be used only with a minimum of 20cm from human body.
• The operation of this device may affect medical electronic devices, such as hearing aids and peacemakers
• The Antennas must be connected to this product prior to connecting the telephone cord.
• The telephone cord must be disconnected prior to disconnecting the Antennas.

YML10WVR HSPA WiFi Router with Voice-User Guide
www.netcommlimited.com 3
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice
Table of Contents
Introduction ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 5
1.1 Features.................................................................................................................................................................................................................5
1.2 Package Contents..................................................................................................................................................................................................5
1.3 LED Indicators........................................................................................................................................................................................................6
1.4 Rear Panel .............................................................................................................................................................................................................7
Quick Setup ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 9
2.1 Setup Procedure ....................................................................................................................................................................................................9
Web User Interface������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ 11
3.1 Default Settings ...................................................................................................................................................................................................11
3.2 TCP/IP Settings....................................................................................................................................................................................................11
3.3 Login Procedure ..................................................................................................................................................................................................14
3.4 Web User Interface Homepage ............................................................................................................................................................................14
3G Settings ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ 16
4.1 3G Service Setup .................................................................................................................................................................................................16
4.2PINConguration.................................................................................................................................................................................................17
Wireless ����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 20
5.2 Security ...............................................................................................................................................................................................................21
5.3Conguration........................................................................................................................................................................................................23
5.4 MAC Filter ............................................................................................................................................................................................................24
5.6 Station Info...........................................................................................................................................................................................................25
Management���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 27
6.1 Device Settings ....................................................................................................................................................................................................27
6.2CongureSNMPagenton3G10WVR ..................................................................................................................................................................29
6.3 Simple Network Time Protocol (SNTP) .................................................................................................................................................................30
6.4 Access Control.....................................................................................................................................................................................................30
6.5 Save and Reboot .................................................................................................................................................................................................32
Advanced Setup ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 34
7.2 Network Address Translation (NAT).......................................................................................................................................................................36
7.3 Security................................................................................................................................................................................................................38
7.4 Routing................................................................................................................................................................................................................40
7.5 Domain Name Servers (DNS)...............................................................................................................................................................................41
Voice����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 43
Status��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 45
8.1 Diagnostics ..........................................................................................................................................................................................................45
8.2 System Log..........................................................................................................................................................................................................46
8.4 Statistics ..............................................................................................................................................................................................................50
8.5 Route...................................................................................................................................................................................................................51
8.6 ARP .....................................................................................................................................................................................................................51
8.7DynamicHostCongurationProtocol(DHCP)......................................................................................................................................................52
8.8 PING....................................................................................................................................................................................................................52
Appendix A: Print Server��������������������������������������������������������������������������������������������������������������������������������������������������������������������� 54
For Windows Vista/7 ..................................................................................................................................................................................................54
For MAC OSX ............................................................................................................................................................................................................57
Appendix B: Samba Server����������������������������������������������������������������������������������������������������������������������������������������������������������������� 59
For Windows Vista/7 ..................................................................................................................................................................................................59
For MAC OSX ............................................................................................................................................................................................................59
Legal & Regulatory Information ���������������������������������������������������������������������������������������������������������������������������������������������������������� 60
Customer Information.................................................................................................................................................................................................60
Federal Communication Commission Interference Statement.....................................................................................................................................61
IC Important Note .....................................................................................................................................................................................................61

Introduction

YML10WVR HSPA WiFi Router with Voice-User Guide
www.netcommlimited.com 5
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice
Introduction
With the increasing popularity of the 3G standard worldwide, this HSPA WiFi Router with Voice provides you with triple-band coverage
through expanding cellular networks throughout the world.
By following the simple step-by-step instructions found on the Connection Manager USB key, you can share your connection with
multiple wireless and wired devices using the 3G network.
Integrating a Sierra Wireless HSPA module, this Router downloads turbo speeds of up to 7.2Mbps.
This Router also provides state-of-the-art security features such as WiFi Protected Access (WPA) data encryption, Firewall and Virtual
Private Networks (VPN) pass through.
1.1 Features
• This HSPA WiFi Router with Voice allows you to share your 3G connection with multiple wireless or wired devices
• Provides you with worldwide coverage through triple-band HSUPA/HSDPA/UMTS (850 / 1900 / 2100MHz), quad-band EDGE/
GSM (850 / 900 / 1800 / 1900 MHz)
• Embedded multi-mode HSUPA/HSDPA/UMTS/EDGE/GPRS/GSM module
• 1 x RJ11 port for voice calling over the 3G network via a connected standard Analogue Telephone (not included).
• Integrated 802.11g/54Mbps AP (backward compatible with 802.11b)
• WiFi Protected Access (WPA)/ WiFi Protected Access 2 (WPA2) and 802.1x wireless encryption
• Static route/ Routing Information Protocol (RIP)/RIP v2 routing functions
• MediaAccessControl(MAC)addressandIPltering
• Network Address Translation (NAT)/ Port Address Translation (PAT)
• Supports Universal Plug and Play (UPnP) and Internet Group Management Protocol (IGMP) snooping
• Supports Virtual Private Network (VPN) Pass-Through
• DynamicHostCongurationProtocol(DHCP)Server/Relay/Client
• Domain Name System (DNS) Proxy and Dynamic Domain Name System (DDNS)
• Web-based Management
• Command Line Interface (CLI) command interface via Telnet
• Congurationbackupandrestoration
• Remoteconguration
• Routerand3Gmodulermwareupgrade
• Supports half-bridging mode
• Supports Simple Network Management Protocol (SNMP)
1.2 Package Contents
Your package contains the following:
• 3G10WVR – HSPA WiFi Router with Voice
• Printed Quick Start Guide
• Ethernet Cable
• Wireless Security Card
• 2 x 3G Antenna
• 1 x WiFi Antenna
• Power Supply

HSPA WiFi Router with Voice-User Guide YML10WVR
6 www.netcommlimited.com
1.3 LED Indicators
The front panel LED indicators are shown in this illustration and followed by detailed explanations in the table below.
LED COLOR MODE DESCRIPTION
POWER Blue On Power on
Off Po wer o ff
Phone Blue On Phone line active
Off Phone line inactive or not connected
Flashing New Voice mail
LAN 1~2 Blue On Powered device connected to the
associated port (includes devices with
wake-on- LAN capability where a slight
voltage is supplied to an Ethernet
connection)
Off No activity, modem powered off, no
cable or no powered device connected
to the associated port
Blink LAN activity present (traffic in either
direction)
WiFi Blue On The wireless module is ready.
Off The wireless module is not installed.
Blink Data being transmitted or received
over WiFi.
Internet Blue Blink Data is transmitted through Internet
connection
Off No connection to the internet or router
powered off
On Internet connection established
3G Blue On Internet connection established.
Blink Connecting with UMTS cellular station
Off No connection with UMTS cellular
station, no activity or router powered
off .
2G Blue On Internet connection established.
Blink Connecting to an EDGE, GPRS or GSM
cellular station
Off No connection with EDGE, GPRS or
GSM cellular station, no activity or
router powered off.
Low Blue On Low signal strength
Off No activity, router powered off or on
other signal strength
Med Blue On Medium signal strength
Off No activity, router powered off or on
other signal strength
High Blue On High signal strength
Off No activity, router powered off or on
other signal strength
NOTE: The six LEDs on the right side of the front panel display (Internet, 3G, 2G, Low, Med, High) will cycle on and off if PIN code protection is activated. In this case, you
should consult section 4.2.1 PIN Code Protection for further instructions.

YML10WVR HSPA WiFi Router with Voice-User Guide
www.netcommlimited.com 7
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice
1.4 Rear Panel
The rear panel contains the ports for data and power connections.
• Main 3G Antenna (removable, SMA connection)
• Power jack for DC power input (12VDC / 1.5A)
• Power button
• USIM card slot
• Aux 3G Antenna (removable, SMA connection)
• USB Port (For connecting a USB Printer or USB Storage Device)
• Reset button
• Phone Port (for Circuit-Switched Voice Call)
• 2 RJ-45 Ethernet Ports

Quick Setup

YML10WVR HSPA WiFi Router with Voice-User Guide
www.netcommlimited.com 9
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice
Quick Setup
2.1 Setup Procedure
These steps explain how to quickly setup your 3G Router:
1. Attach the two 3G antennas provided to the ports marked Main and AUX on the back of the router. The antennas should be
screwed in a clockwise direction.
2. Insert your SIM card (until you hear a click) into the USIM slot at the back of the Router.
3. Connect the yellow networking cable to one of the yellow ports found at the back of the Router.
4. Connect the other end of the yellow networking cable to the port on your computer.
5. If required, connect a standard Analogue Telephone to the port labeled “Phone” using an RJ-11 Cable (not included)
6. Connect the power adapter to the Power socket on the back of the Router.
7. Plug the power adapter into the wall socket and press the power button into the ON position (in).
8. ConguretherouterthroughtheWebUserInterface(WUI).
NOTE: Chapters 3 through 8 explain how to setup and use the WUI
9. Savetheroutercongurationandreboot(seesection6.5).
Telephone USB
Storage
Laptop
Computer
Computer
3G Tower
Smart Phone
Printer

Web User Interface

YML10WVR HSPA WiFi Router with Voice-User Guide
www.netcommlimited.com 11
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice
Web User Interface
This section describes how to access the device via the web user interface using a web browser such as Microsoft Internet Explorer
(version 6.0 or later).
3.1 Default Settings
The following are the default settings for the device.
• Local (LAN) access (username: admin, password: admin)
• Remote (WAN) access (username: support, password: support)
• User access (username: user, password: user)
• LAN IP address: 192.168.1.1
• Remote WAN access: disabled
• NATandrewall:enabled
• DynamicHostCongurationProtocol(DHCP)serveronLANinterface:enabled
Technical Note:
Duringpoweron,thedeviceinitializesallsettingstodefaultvalues.Itwillthenreadthecongurationprolefromthepermanentstoragesectionofashmemory.Thedefault
attributesareoverwrittenwhenidenticalattributeswithdifferentvaluesarecongured.Thecongurationproleinpermanentstoragecanbecreatedviathewebuserinterface
ortelnetuserinterface,orothermanagementprotocols.Thefactorydefaultcongurationcanberestoredeitherbypushingtheresetbuttonformorethanvesecondsuntilthe
powerindicatesLEDblinkingorbyclickingtheRestoreDefaultCongurationoptionintheRestoreDefaultSettingsscreen.
3.2 TCP/IP Settings
It is likely that your computer will automatically obtain an IP Address and join the network. This is because the Dynamic Host
CongurationProtocol(DHCP)server(onthedevice)willstartautomaticallywhenyourRouterpowersup.
ThisautomaticassignmentrequiresthatDHCPisconguredonyourcomputers.Itislikelythatthisisalreadythecase,butshouldyou
berequiredtocongurethis,pleaseseetheinstructionsbelow.
Windows XP/Vista/7
DHCP Mode
WhenyourRouterpowersup,theDynamicHostCongurationProtocolDHCPserver(onthedevice)willstartautomatically.Tosetyour
PC for DHCP mode, check the Internet Protocol properties of your Local Area Connection. You can set your PC to DHCP mode by
selecting Obtain an IP address automatically in the dialog box shown below.

HSPA WiFi Router with Voice-User Guide YML10WVR
12 www.netcommlimited.com
STATIC IP Mode
TocongureyourRoutermanually,yourPCmusthaveastaticIPaddresswithintheRouter’ssubnet.Thefollowingstepsshowhowto
congureyourPCIPaddressusingsubnet192.168.1.x.ThefollowingassumesyouarerunningWindowsXP.
1. From the Network Connections window, open Local Area Connection (You may also access this screen by double-clicking the
Local Area Connection icon on your taskbar). Click the Properties button.
2. Select Internet Protocol (TCP/IP) and click the Properties button. The screen should now display as below. Change the IP
address to the domain of 192.168.1.x (1<x<254) with subnet mask of 255.255.255.0. Set the default router and DNS server to
therouter’sIPaddress.
NOTE: TheIPaddressoftherouteris192.168.1.1(default),sothePCmustbesetwithadifferentIP.Inthecasebelow,thePC’sIPaddressissetas192.168.1.2
3. Click OK to submit the settings.

YML10WVR HSPA WiFi Router with Voice-User Guide
www.netcommlimited.com 13
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice
MAC OSX 10�4
DHCP Mode
To set your Apple Mac for DHCP mode, browse to the Apple menu and select System Preferences. In the System Preferences menu,
clickontheNetworkiconandselectEthernet.NextselectUsingDHCPfromtheConguredropdownlist.AfterclickingApply,your
Mac’sIPAddresswillnowbeautomaticallyassignedfromtheGateway.
STATIC Mode
IfyoudonotwishtouseautomaticassignmentofIPAddressesandwishtocongureyourRoutermanually,yourcomputermusthave
astaticIPaddresswithintheRouter’ssubnet.Thefollowingstepsshowhowtocongureyourcomputer’sIPaddresswithinthesubnet
192.168.1.x
1. Browse to the Apple menu and select System Preferences. From the System Preferences, click the Network icon and select the
Ethernet connection.
2. FromtheConguredropdownlist,youcansetyourcomputertoStaticIPmodebyselectingthe“Manually”option.
3. Choose an IP address between 192.168.1.2 – 192.168.1.254 (Do not choose the Router IP of 192.168.1.1). Enter this IP
addressintotheeldmarkedIPAddress,andenteraSubnetMaskof255.255.255.0
4. SettheRouterandDNSservereldto192.168.1.1(TheRouter’sIPaddress).
NOTE: TheIPaddressoftherouteris192.168.1.1(default),sothecomputermustbesetwithadifferentIPtotherouter.Inthecasebelow,thePC’sIPaddressissetas
192.168.1.2
5. Click Apply to submit the settings.

HSPA WiFi Router with Voice-User Guide YML10WVR
14 www.netcommlimited.com
3.3 Login Procedure
To login to the web interface, follow the steps below:
NOTE: The default settings can be found in 3.1 Default Settings.
1. OpenawebbrowserandenterthedefaultIPaddressfortheRouterintheWebaddresseld.Inthiscasehttp://192.168.1.1.
NOTE: For local administration (i.e. LAN access), the PC running the browser must be attached to the Ethernet, and not necessarily to the device. For remote access, use
the WAN IP address shown on the WUI Homepage screen and login with remote username and password.
2. Adialogboxwillappear.Enterthedefaultusernameandpassword,asdenedinsection3.1
Default Settings.
Click OK to continue.
NOTE: The login password can be changed later (see 6.4.3 Passwords)
3. Aftersuccessfullylogginginforthersttime,youwillreachthisscreen.
3.4 Web User Interface Homepage
The web user interface (WUI) is divided into two window panels, the main menu (on the top) and the display screen (on the bottom). The
main menu has the following options: Basic, 3G Settings, Wireless, Management, Advanced, and Status.
Selecting one of these options will open a submenu with more options. Basic is discussed below while subsequent chapters introduce
the other main menu selections.
NOTE: Themenuoptionsavailablewithinthewebuserinterfacearebaseduponthedevicecongurationanduserprivileges(i.e.localorremote).
BASIC / HOME
TheBasic/HomescreenistheWUIhomepageandtherstselectiononthemainmenu.Itprovidesinformationregardingthermware,
3G,andIPconguration.
The following table provides further details
FIELDS DESCRIPTION
Software version The software version of the device.
Hardware version The Hardware version of the device
Bootloader version The bootloader version of the device.
Wireless driver version The wireless driver version of the wireless module.
Network The name of or other reference to the mobile network operator.
Link Shows the connection status of the current 3G connection.
Mode The radio access technique currently used to enable internet access. It can be
HSUPA, HSDPA, UMTS, EDGE, GPRS or Disconnected.
Signal strength The mobile network (UMTS or GSM) signal quality available at the device
location. This signal quality affects the performance of the unit. If two or more
bars are green, the connection is usually acceptable.
SIM info Shows the SIM card status on the device.
LAN IP Address Shows the IP address for LAN interface.
WAN IP Address Shows the IP address for WAN interface.
Default Gateway Shows the IP address of the default gateway for the WAN interface.
Primary DNS Server Shows the IP address of the primary DNS server.
Secondary DNS Server Shows the IP address of the secondary DNS server.
Date/Time Thetimeaccordingtothedevice’sinternalclock
Online Help Click this Icon for Online User Guide

3G Settings

HSPA WiFi Router with Voice-User Guide YML10WVR
16 www.netcommlimited.com
3G Settings
4.1 3G Service Setup
Selectyour3Gservicesettingsaccordingtopredenedorcustomproles.Setupinstructionsareprovidedinthefollowingsectionsfor
your assistance.
4�1�1 3G Settings
Thismenuincludes3GserviceSetupandPINConguration.
NOTE: Sections 8.3 and 8.4.2 also provide information about the 3G service.
4.1.2 ProleSetup
YourServiceProviderwillprovidetheinformationrequiredtocompletethersttimesetupinstructionsbelow.Thisincludesprole,
username and password. Only complete those steps for which you have information and skip the others.
1. If your SIM card is not inserted into the Router, then do so now.
2. TypetheAPNintheAPNeld.AuthenticationMethodshouldbeprovidedbyyourInternetserviceprovider;orjustleaveitto
AUTOifnotacquired.Ifyouhavenotreceivedtheusernameandpassword.,leavetheseeldsempty.
3. Select IP compression and Data compression to be ON or Off. By default they are set to off.
4. Click the Save button to save the new settings.
5. Press the Connect button to reboot the router and to connect to Internet. After reboot, the Device Info for
3G network box in the WUI Basic screen should indicate an active connection, as shown below. The 3G and
Internet LEDs on the front panel of the Router should also be blinking.
IftheLEDsareoff,theneitheryourprolesettingsareincorrect,theSIMcardisnotworkingortheservicenetworkisunavailable.In
either case, contact Technical Support for further instructions.
NOTE: If the LEDs light in an on/off pattern moving from left to right this indicates that your SIM is PIN Locked, please lee PIN Lock Off on page 21 for instruction on how
toxthis

YML10WVR HSPA WiFi Router with Voice-User Guide
www.netcommlimited.com 17
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice
4.2PINConguration
This screen allows for changes to the 3G SIM card PIN code protection settings.
NOTE: If you have entered the incorrect PIN 3 times, your SIM card will be locked for your security. Please call your 3G Provider for assistance.
4�2�1 PIN Code Protection
PIN code protection prevents the use of a SIM card by unauthorized persons. To use the 3G internet service with this router however,
the PIN code protection must be disabled. If the SIM card inserted into the Router is locked with a PIN code, the web user interface will
display the following screen after login.
PIN Lock Off
IfyouwishtoconnecttotheInternetusingaPINlockedSIMcard,youmustrstturnPINcodeprotectionOff.SelectPINlockOff,enter
thePINCodetwice.Pleasekeepinmindyouonlyhave3attemptsbeforeyourSIMcardislocked.Theremainingattempts’number
shows how many attempts left. Contact Your 3G Carrieryour 3G Carrier if you require assistance. You can select Remember PIN Code
toONsoyoudon’tneedtoinputthePINcodeeverytime
when the router turns on. Afterwards, click Apply. The following dialog box should now appear.
PIN Lock On
AfteryouarenishedusingyourSIMcardforInternetservice,youmaywishtolockitagain.Inthiscase,rstgotothe3GSettings-PIN
Congurationscreen,asshownbelow.SelectPINlockON,enterthePINcodetwice.YoucanselectRememberPINcodetoYesso
youdon’tneedtoinputthePINcodeeverytimewhentherouterturnson.
After you do so, the following dialog box should appear.
You can now return your SIM card to your cellular phone or other mobile device.

HSPA WiFi Router with Voice-User Guide YML10WVR
18 www.netcommlimited.com
4�2�2 PIN Code Change
If you wish to change your PIN code for greater security, enable the PIN Code protection. Go to the previous section and follow the
procedure listed under PIN Lock On.
AfterlockingtheSIMcard,selectPINCodeChangeandenteryourOldandNewPINcodesintheeldsprovided.Keepinmindyou
onlyhave3attemptsbeforeyourSIMcardislocked.Theremainingattempts’numbershowshowmanyattemptsleft.ContactYour3G
Carrier if you require assistance. Afterwards, click Apply to activate the change.
NOTE: IfyouforgettochangethePINCodewithoutrstturningonPINlockprotection,youwillseethisdialogboxasahelpfulreminder.
NOTE: If your PIN Code change request was successful the following dialog box will display.

Wireless

HSPA WiFi Router with Voice-User Guide YML10WVR
20 www.netcommlimited.com
Wireless
TheWirelesssubmenuprovidesaccesstoWirelessLocalAreaNetwork(LAN)congurationsettingsincluding:
• Wireless network name
• Channel restrictions (based on country)
• Security
• Access point or bridging behaviour
• Station information
5.1 Setup
ThisscreenallowsyoutocongurebasicfeaturesofthewirelessLANinterface.YoucanenableordisablethewirelessLANinterface,
hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country
requirements. The Wireless Guest Network function adds extra networking security when connecting to remote hosts.
OPTION DESCRIPTION
Enable Wireless A checkbox that enables (default) or disables the wireless LAN interface. When
selected, the Web UI displays Hide Access point, SSID, BSSID and Country
settings.
Hide Access Point Select Hide Access Point to protect the access point from detection by wireless
active scans. To check AP status in Windows XP, open Network Connections
from the start Menu and select View Available Network Connections. If the
access point is hidden, it will not be listed there. To connect a client to a hidden
access point, the station must add the access point manually to its wireless
configuration.
SSID [1-32 characters] Sets the wireless network name. SSID stands for Service Set Identifier. All
stations must be configured with the correct SSID to access the WLAN. If the
SSID does not match, that user will not be granted access.
BSSID The BSSID is a 48bit identity used to identify a particular BSS (Basic Service
Set) within an area. In Infrastructure BSS networks, the BSSID is the MAC
(Media Access Control) address of the AP (Access Point) and in Independent
BSS or ad hoc networks, the BSSID is generated randomly.
Country A drop-down menu that permits worldwide and specific national settings.
Wireless Guest The Guest SSID (Virtual Access Point) can be enabled by selecting the Enable
Wireless Guest
Network checkbox Rename the Wireless Guest Network as you wish.
NOTE: wireless hosts cannot scan Guest SSIDs.