NETGEAR FS608 User manual

Installation Guide
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make
changes to the product described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the NETGEAR Model FS608 Fast Ethernet Switch has been suppressed in accordance with the
conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example,
test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the
notes in the operating instructions.
Federal Office forTelecommunications Approvals has been notified of the placing of this equipment on the market and
has been granted the right to test the series for compliance with the regulations.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
EN 55 022 Declaration of Conformance
This is to certify that the NETGEAR Model FS608 Fast Ethernet Switch is shielded against the generation of radio
interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by
the application of EN 55 022 Class B (CISPR 22).
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (NETGEAR Model FS608 Fast Ethernet Switch) does not exceed the Class B limits for radio-noise
emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (NETGEAR Model FS608 Fast Ethernet Switch) respecte les limites de bruits radioélectriques
visant les appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des
Communications du Canada.
April 2002
*M1-FS608NA-0*
M1-FS608NA-0

Introduction
The NETGEAR® 8-Port Fast Ethernet Switch Model FS608 provides you with a low-cost,
reliable, high-performance switch to connect up to eight different Ethernet-enabled devices
(such as computers, file servers, print servers, printers, routers and hubs).
You use the FS608 switch to build a small network that enables you to have 10 Mbps or
100 Mbps access to other devices on the network. Also, with this switch, you can add extra
computers to your cable or DSL router. Unlike a hub that shares its connection with all
devices, the FS608 switch provides a full, dedicated 100 Mbps (or 10 Mbps) connection
between two devices. If a device has full-duplex capability, the FS608 switch provides a
200 Mbps (or 20 Mbps) connection.
Ethernet cables come as either straight-through or crossover cables—depending on whether
you’re connecting to a device (computer, server, or printer) or networking equipment (hub,
switch, or router). With the Auto Uplink™ feature, you don’t have to worry about which one
you use. Each port on the FS608 switch automatically configures itself correctly when you plug
in a device’s cable.
If you have a problem with your switch, NETGEAR offers support 24 hours a day and 7 days
a week on the Web (www.NETGEAR.com), by e-mail ([email protected]) and by
phone (see the provided support information card for phone numbers).
Installation Overview
Estimated Time: 5–10 minutes
1. Unpack the box and verify the contents.
2. Prepare to install the switch.
3. Install the switch and connect the other devices.
NETGEAR, INC.
4500 Great America Parkway
Santa Clara, CA 95054
USA
Support Information
Phone: 1-888-NETGEAR
E-mail: [email protected]
www.NETGEAR.com
Technical Support
YOU MUST REGISTER TO OBTAIN TECHNICAL SUPPORT. PLEASE RETAIN
PROOF OF PURCHASE and the warranty information.
To register your product, get product support or obtain product information and product
documentation, go to http://www.NETGEAR.com/register.
You’ll find technical support information at: http://www.NETGEAR.com/ through the
customer service area. If you want to contact technical support by telephone, see the support
information card for the correct telephone number for your country.
NETGEAR, Inc.
© 2002 by NETGEAR, Inc. All rights reserved.
NETGEAR and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc. in the United States
and/or other countries.
Other brand and product names are trademarks or registered trademarks of their respective holders.
Information is subject to change without notice.
Fast Ethernet Switch FS608

Unpack the Box and Verify the
Contents
When you open the box, verify that you received everything. The package includes:
• 8-Port Fast Ethernet Switch FS608
• AC power adapter
• Vertical stand and cable strap
• Wall-mounting screws
•FS608 Installation Guide (this document)
• Warranty and registration card
• Support information card
If you don’t have everything listed above, see the support information card for contact
information. If you’re missing the support information card itself, get contact information at
www.NETGEAR.com in the Customer Service area
Installation guide,
warranty/registration card
and support
information card
Power adapter
Wall-mount
hardware
Fast Ethernet Switch FS608
Stand
1
1Prepare to Install the Switch
Decide where you want to place the switch. Find a flat horizontal surface — such as a table,
desk or shelf. The switch comes with wall-mounting screws and a vertical stand. You’re
welcome to use the screws if you want to hang the switch in an open space on a wall. Use the
vertical stand if you cannot provide adequate clear space on all sides with the switch in a
horizontal position.
Make sure the selected location is:
• Not in direct sunlight or near a heater or heating vent.
• Not cluttered or crowded.There should be at least 2 inches (5 cm) of clear space on all
sides of the switch.
• Well ventilated (especially if it is in a closet).
Also, you’ll need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each device
you want to connect to the switch. Each Ethernet cable must be less than 328 feet (100 meters).
2
2

Install the Switch and Connect the
Other Devices
1. Place the switch on a flat surface or hook onto the screws.
2. For each device, insert one end of an Ethernet cable into the port in the device and insert
the other end into one of the Ethernet ports on the switch.
Note: If you have more than 8 devices to connect to this switch, you must connect
them to a hub or other switch and then connect that hub or switch to this switch.
3. Connect the power adapter’s cord into the back of the switch and then plug the adapter
into a power source (such as a wall socket or power strip).
The Power light should light up.
The corresponding port
number for each connected
and powered device should
light and flash when activity occurs: green for 100 Mbps connections and yellow for
10 Mbps connections.
Note: If any light doesn’t operate as indicated, go to the Troubleshooting section.
3
3
Fast Ethernet Switch FS608 Cable/DSL Web Safe Router RP614
DSL
modem
Troubleshooting
The Power light is not lit
The switch has no power.
• Make sure the power cord is properly connected to the switch.
• Make sure the power adapter is properly connected to a functioning power outlet. If it’s
in a power strip, make sure the power strip is turned on. If the socket is controlled by a
light switch, make sure the switch is in the on position.
• Make sure you are using the NETGEAR power adapter supplied with your switch.
The Port number light is not lit for a connected device or
stays on continuously
There’s a hardware connection problem.
• Make sure the cable connectors
are securely plugged in at the switch and the device.
• Make sure the connected device is turned on.
• If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure the card
or adapter is installed correctly and is working.
• Make sure the cable is less than 328 feet (100 meters).
Technical Specifications
Standards Compatibility: IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u,100BASE-TX Fast Ethernet
IEEE 802.3x Flow Control; compatible with Windows®, Mac® OS, NetWare®,
Linux®
Data Rate: 100 Mbps with 4B/5B encoding and MLT-3 physical interface for 100BASE-TX
10 or 100 Mbps half-duplex
Network Interface: RJ-45 connector for 10BASE-T or 100BASE-TX Ethernet interface
Power: 7.5 W max and 7.5 V @ 1A DC input
Physical Dimensions: W: 175 mm (6.89") D: 118 mm (4.65") H: 28 mm (1.10")
Weight: 0.276 kg (0.608 lbs)
Operating Temperature: 0 to 40˚ C (32 to 104˚ F)
Operating Humidity: 10% t0 90% relative humidity, non-condensing
Electromagnetic Compliance: CE mark, Commercial; FCC Part 15, Class B; EN 55 022 (CISPR 22), C-Tick
Safety Agency Approvals for
the Power Adapter: CE mark, Commercial UL listed (UL 1950), TUV licensed (EN 60950), C-Tick
Performance Specifications
Frame Filter Rate: 14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port
Frame Forward Rate: 14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port
Network Latency: 100 Mbps to 100 Mbps: 20 µs max
(using 64-byte packets)
Address Database Size: 1000 MAC addresses
Addressing: 48-bit MAC address
Queue Buffer: 128 kilobytes