NETGEAR FSM7326P - ProSafe Managed Switch Manual

201-10815-01
March 2006
NETGEAR, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Managed Layer 3 Switches
FSM7326P, GSM7312, and
GSM7324 Hardware
Installation Guide

Publication Version 1.0, March 2006
© 2006 by NETGEAR, Inc. All rights reserved. Information is subject to change without notice.
Trademarks
The Netgear Logo, the Gear Guy, Everybody’s connecting, and ProSafe are trademarks or registered trademark of
Netgear, Inc. in the United States and other countries. Microsoft, Windows, and the Windows logo are trademarks or
registered trademarks of Microsoft Corporation in the United States and other countries. Other brand and product names
are trademarks or registered trademarks of their respective holders.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the NETGEAR ProSafe™ 24-Port 10/100 L3 Managed Switch with 2 Gigabit Ports and PoE
FSM7326 has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/
1992.The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however,
be subject to certain restrictions. Please refer to the notes in the operating instructions.
It is hereby certified that the NETGEAR ProSafe™ 12 Port Gigabit L3 Managed Switch Model GSM7312 has been
suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992.The operation
of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to
certain restrictions. Please refer to the notes in the operating instructions.
It is hereby certified that the NETGEAR ProSafe™ 24 Port Gigabit L3 Managed Switch Model GSM7324 has been
suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992.The operation
of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to
certain restrictions. Please refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market
and has been granted the right to test the series for compliance with the regulations.
Voluntary Control Council for Interference (VCCI) Statement
This is Class A product based on the standard of the Voluntary Control Council for Interference by Information
Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio interference may occur, in
which case, the user may be required to take corrective actions.”

Publication Version 1.0, March 2006
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (NETGEAR ProSafe™ 24-Port 10/100 L3 Managed Switch with 2 Gigabit Ports and PoE
FSM7326) does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio
Interference Regulations of the Canadian Department of Communications.
This digital apparatus (NETGEAR ProSafe™ 12 Port Gigabit L3 Managed Switch Model GSM7312) does not exceed
the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This digital apparatus (NETGEAR ProSafe™ 24 Port Gigabit L3 Managed Switch Model GSM7324) do not exceed the
Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the
Canadian Department of Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (NETGEAR Model ProSafe™ 24-Port 10/100 L3 Managed Switch with 2 Gigabit Ports and
PoE FSM7326) respecte les limites de bruits radioélectriques visant les appareils numériques de classe A prescrites dans
le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada.
Cet appareil numérique (NETGEAR ProSafe™ 12 Port Gigabit L3 Managed Switch Model GSM7312 ) respecte les
limites de bruits radioélectriques visant les appareils numériques de classe A prescrites dans le Règlement sur le
brouillage radioélectrique du ministère des Communications du Canada.
Cet appareil numérique (NETGEAR ProSafe™ 24 Port Gigabit L3 Managed Switch Model GSM7324) respecte les
limites de bruits radioélectriques visant les appareils numériques de classe A prescrites dans le Règlement sur le
brouillage radioélectrique du ministère des Communications du Canada.
EU Declaration of Conformity
This is to declare that the NETGEAR FSM7326P, GSM7312, and GSM7324 managed switches are compliant with
EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC. Conformity is declared by application of EN55022
Class A, EN55024 and EN60950.

Publication Version 1.0, March 2006
Customer Support
Refer to the Support Information Card that shipped with your Managed Layer 3
Switch.
World Wide Web
NETGEAR maintains a World Wide Web home page that you can access at the
universal resource locator (URL) http://www.netgear.com. A direct connection to
the Internet and a Web browser such as Internet Explorer or Netscape are required.
Product and Publication Details
Model Number: FSM7326P, GSM7312, and GSM7324
Publication Date: March 2006
Product Family: managed switch
Product Name: Managed Layer 3 Switch
Home or Business Product: Business
Language: English
Publication Part Number: 201-10815-01
Publication Version Number 1.0

Publication Version 1.0, March 2006
v
Contents
Chapter 1
About This Manual
Audience, Conventions, Formats, and Scope ................................................................1-1
Chapter 2
Introduction
FSM7326P Front Panel and LEDs .................................................................................2-1
FSM7326P Rear Panel ...................................................................................................2-3
GSM7312 Front Panel and LEDs ...................................................................................2-3
GSM7312 Rear Panel ....................................................................................................2-4
GSM7324 Front Panel and LEDs ...................................................................................2-5
GSM7324 Rear Panel ..............................................................................................2-6
Safety Instructions ..........................................................................................................2-6
Chapter 3
Hardware Installation
Package Contents ..........................................................................................................3-1
Protecting Against Electrostatic Discharge .....................................................................3-2
Unpacking the Hardware ................................................................................................3-2
Installation ......................................................................................................................3-3
Select a Location ......................................................................................................3-3
Install the Switch ......................................................................................................3-5
Check the Installation ...............................................................................................3-6
Connect to Power and Check the LEDs ...................................................................3-6
Connecting Equipment to the Switch ..............................................................................3-7
RJ-45 Ports ..............................................................................................................3-7
Gigabit Module Bay .................................................................................................3-7
Connecting a Console to the Switch ...............................................................................3-8
Chapter 4
Troubleshooting
Troubleshooting Chart ...................................................................................................4-1

Publication Version 1.0, March 2006
vi
Additional Troubleshooting Suggestions .......................................................................4-2
Appendix A
Technical Specifications ......................................................................................................A1
Appendix B
Default Configuration Settings............................................................................................B1

1-1
v1.0, March 2006
Chapter 1
About This Manual
The Managed Layer 3 Switches FSM7326P, GSM7312, and GSM7324 Hardware
Installation Guide describes how to install the NETGEAR®FSM7326P,
GSM7312, and GSM7324 switches.
Audience, Conventions, Formats, and Scope
This guide is intended for network managers familiar with network management
concepts and terminology. This guide uses the following typographical
conventions:
This guide uses the following formats to highlight special messages:
Table 1-1. Typographical Conventions
Italics Emphasis, books, CDs, URL names
Bold User input
Fixed Screen text, file and server names, extensions, commands, IP
addresses
Note: This format is used to highlight information of importance or
special interest.
Tip: This format is used to highlight a procedure that will save time or
resources.
Warning: Ignoring this type of note may result in a malfunction or
damage to the equipment.

Managed Layer 3 Switches FSM7326P, GSM7312, and GSM7324 Hardware Installation Guide
1-2 About This Manual
v1.0, March 2006
This manual is written for the Managed Layer 3 Switch according to these
specifications:
Danger: This is a safety warning. Failure to take heed of this notice may
result in personal injury or death.
Table 1-2. Manual Scope
Product Version ProSafe 24 Port 10/100 L3 Managed Switch with 2
Gigabit Ports and PoE FSM7326P
ProSafe 12 Port Gigabit L3 Managed Switch Model
GSM7312
ProSafe 24 Port Gigabit L3 Managed Switch Model
GSM7324
Manual Publication Date March 2006
Note: Product updates are available on the NETGEAR, Inc. Web site at
http://kbserver.netgear.com.

Introduction 2-1
v1.0, March 2006
Chapter 2
Introduction
The NETGEAR Layer 3 Managed Fast Ethernet Switch is a state-of-the-art, high-
performance, IEEE-compliant network solution. It includes powerful
management features that you can use to eliminate bottlenecks, boost
performance, and increase productivity.
This guide describes the hardware for the following NETGEAR switches:
•ProSafe 24 Port 10/100 L3 Managed Switch with 2 Gigabit Ports and PoE
FSM7326P
• ProSafe 12 Port Gigabit L3 Managed Switch Model GSM7312
• ProSafe 24 Port Gigabit L3 Managed Switch Model GSM7324
These switches can be free-standing or rack-mounted in a wiring closet or an
equipment room. For information about features for each product, see the
NETGEAR Web site at http://www.netgear.com.
FSM7326P Front Panel and LEDs
The following figure shows the front panel of the FSM7326P. The front panel
contains LEDs, RJ-45 jacks, SFP module bays, and a console port.
Figure 2-1
SFP module bays Console
RJ-45 jacks
LEDs port

Managed Layer 3 Switches FSM7326P, GSM7312, and GSM7324 Hardware Installation Guide
2-2 Introduction
v1.0, March 2006
The following table describes the LEDs on the front panel of the switch.
Table 2-1. LED Descriptions for FSM7326P
LED Description
PWR (power) Green: Power is supplied, and the switch is operating normally.
Blinking yellow: The switch is performing boot-up diagnostics.
Off: Power is not present.
RPS (redundant
power supply) •Green: RPS is detected. •Off: RPS is either not present or is not functional.
Max PoE • Yellow: Power supply has reached its maximum load, and no more
powered devices can be attached to the switch.
•Off: More PoE powered devices can be attached to the switch.
10/100M Fast
ports: LINK,
SPEED/ACT, and
PoE
LINK
•Green: Link in full duplex.
•Yellow: Link in half duplex.
SPEED/ACT (Activity)
• Solid green: Link in 100 Mbps.
•Blinking green: The port is sending or receiving packets at
100 Mbps.
•Solid yellow: A valid 10-Mbps link is established on the port.
•Blinking yellow: The port is sending or receiving packets at
10 Mbps.
PoE
•Solid green: Power is being provided to a powered device through
this port.
10/100/1000M
Combo ports:
LINK,
SPEED/ACT, and
1000M/ACT
LINK
•Green: Link in full duplex.
•Yellow: Link in half duplex.
SPEED/ACT (Activity)
• Solid green: Link in 100 Mbps.
•Blinking green: The port is sending or receiving packets at
100 Mbps.
•Solid yellow: A valid 10-Mbps link is established on the port.
•Blinking yellow: The port is sending or receiving packets at
10 Mbps.
1000M/ACT (Activity)
• Solid green: Link in 1,000 Mbps.
•Blinking green: The port is sending or receiving packets at
1000 Mbps.