NETGEAR JFS524F User manual

この装置は、クラスA情報技術装置です。この装置を家庭環境で使用すると電波妨害を
引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要求される
ことがあります。
201-10520-01
ProSafe 10/100 Switch W/100FX
NETGEAR, ProSafe, and Auto Uplink are registered trademarks of NETGEAR, Inc in the United States and
other countries. All other trademarks and registered trademarks are the property of their respective owners.
2005
By certified that the NETGEAR Prosafe JFS524F Fast Ethernet Switch W/100FX has been
This is to certify that the NETGEAR Prosafe JFS524F Fast Ethernet Switch W/100FX is shielded against
the generation of radio interference in accordance with the application of Council Directive 89/336/EEC,
Article 4a. Conformity is declared by the application of EN35 022 Class A (CISPR 22).
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interferences in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interferences to radio communications. However, there is no guarantee that interference
will not occur in a particular installation if this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures.
This digital apparatus (NETGEAR Prosafe JFS524F Fast Ethernet Switch W/100FX ) does not exceed the Class
A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations o f the
Canadian Department of Communications.
Cet appareil numérique (NETGEAR Prosafe JFS524F Fast Ethernet Switch W/100FX ) respecte les limites de
bruits radioélectriques visant les appareils numériques de class A rpescrites dans le Reglement sur le brouillage
radioélectrique du mimisére des Communications du Canada.
524F524F

IEEE 802.3i 10BASE-T Ethernet
IEEE 802.3 100BASE-FX Fast Ethernet
IEEE 802.3x Flow Control
Compatible with major network software, including Windows, NetWare, and Linux
The NETGEAR®ProSafe JFS524F 24 Port 10/100 Mbps Switch with 100FX provides you with a low-cost, high-performance
network solution and are designed to support power workgroups operating at either 10 megabits per second (Mbps) or 100 Mbps.
Optional SC module (AF711F)
The modularity of ProSafe JFS524F switch provides you with a highly adaptable network. You can not only configure your
network for 100FX fiber uplink, but, you also can opt to expand your network gradually and affordably as needed.
To install an optional 100FX SC module (AF711F)
a. Unscrew and remove the module cover plate.
b. Insert the module (AF711F) into the slot, press firmly to seat the module.
c. Tighten the module screws.
d. Power OFF and Power ON again if power has remained ON throughout the installation of SC module (AF711F).
With the ProSafe JFS524F 24 Port 10/100 Mbps Switch with optional 100FX module (AF711F), improvement is accomplished very
easily, with no change to the desktop (the network interface cards or software and the network wiring). As a result, the performance
upgrade and the applications it enables are obtained very quickly and at a low cost.
ProSafe
ProSafe JFS524F switch is used as a desktop switch to build a small network that enables users to have 100 Mbps access to a file
server. If a full-duplex adapter card is installed in the server or PC, a 200Mbps connection is possible on the port where the server or
PC is completed.
6.9W
328x43.2x169mm
1.6kg/3.5 lbs
VCCI Class A/ FCC Class A/ CE/ C-tick/ MIC
256KB
110987.8 hrs (12.7 yrs)
CUL
ProSafe
Model JFS524F
Packet transmission or receiving on the port.
Valid Link on the port.
Blinking
Solid
Description
The port is operating in 10 Mbps mode, if corresponding L/A LED
is Solid or Blinking
(Port Number)
SC Link/Act
(Optional)
On
Blinking
Valid Link on the port
Packet transmission or receiving on the port
Maximum
MTBF

Print material spec.
material: coated 100lb art paper
color: black and white with minimum 300 dpi grayscale images
Binding: make two fold
dimension: 400(W) x 260(H) mm (before folded)
200(W) x 130(H) mm (after folded)
Project source files: illustrator 10
*Page 3 is not part of QIG, please do not print.