NETGEAR ProSafe GS105v3 User manual

)NSTALLATION'UIDE
ProSafe 5-Port Gigabit Ethernet Switch GS105v3
Estimated installation time: 5-10 minutes
Package Contents
The package includes:
• ProSafe 5-Port Gigabit Ethernet Switch GS105v3
• AC power adapter
•GS105v3 Installation Guide (this document)
• Warranty/Support information card
Prepare to Install the Switch
Decide where you want to place the switch. Find a flat horizontal surface such as a table,
desk or shelf. You can use wall-mounting screws (not provided) to hang the switch in an
open space on a wall.
Make sure the selected location is:
• Not in direct sunlight or near a heater or heating vent.
• Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on
all sides of the switch.
• Well ventilated (especially if it is in a closet).
Depending on the speed of your network devices, you need a Category 3 (10 Mbps),
Category 5 (100 Mbps) or Category 5e (1000 Mbps) Ethernet cable with RJ-45 connectors
for each device you want to connect to the switch. Each Ethernet cable must be less than
328 feet (100 meters).
Install the Switch and Connect the Other Devices
1. Place the switch on a flat surface or hook onto the screws.
2. For each device, insert one end of an Ethernet cable into the port in the device and
insert the other end into one of the Ethernet ports on the switch.
3. Connect the power adapter cord into the back of the switch and then plug the adapter
into a power source (such as a wall socket or power strip).
4. Check the LEDs to verify that the equipment is connected correctly.
• The Power LED is lit.
• Each RJ-45 jack has 2 LEDs. For each jack that is connected to a powered
device, the Link LED is lit, and it flashes when activity occurs. If the connection
is 10 Mbps or 100 Mbps, one LED lights up. If the connection is 1000 Mbps,
both LEDs light up.
Note: If any light does not operate as indicated, go to the Troubleshooting section.
GS105v3 5-Port
Gigabit Ethernet Switch
modem
firewall
Power
100 Mbps
10 Mbps LED
Both LEDs light for
a 1000 Mbps connection.
Troubleshooting
The Power light is not lit.
The switch has no power.
• Make sure that the power cord is correctly connected to the switch.
• Make sure that the power adapter is connected to a functioning power outlet. If it is in
a power strip, make sure that the power strip is turned on. If the socket is controlled
by a light switch, make sure that the switch is in the on position.
• Make sure you that are using the NETGEAR power adapter supplied with your
switch.
The Port number light is not lit for a connected device or stays on continuously.
There is a hardware connection problem.
• Make sure that the cable connectors are securely plugged in at the switch and the
device.
• Make sure that the connected device is turned on.
• If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure that
the card or adapter is installed correctly and is working.
• Make sure that the cable is less than 328 feet (100 meters).

June, 2008
This symbol was placed in accordance with the European Union Directive
2002/96 on the Waste Electrical and Electronic Equipment (the WEEE
Directive). If disposed of within the European Union, this product should be
treated and recycled in accordance with the laws of your jurisdiction
implementing the WEEE Directive.
© 2008 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered
trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and product
names are trademarks or registered trademarks of their respective holders. Information is subject to
change without notice.
.
Technical Specifications
Standards compatibility ISO/IEG 802.3i (ANSI/IEEE 802.i) 10BASE-T, IEEE 802.3i
10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3z
1000BASE-T, IEEE 802.3x Flow Control; Jumbo frame 9K,
IEEE 802.1p priority; DSCP priority. Compatible with
Windows, Mac OS, NetWare, Linux.
Network interface RJ-45 connector for 10BASE-T, 100BASE-T, or 1000BASE-T
Ethernet interface
Power 12W max and 12V@1A DC input
Power consumption 3W max
Physical dimensions W: 104 mm (4.1") D: 94 mm (3.7") H: 27 mm (1.1")
Weight 0.28 kg (0.621 lbs)
Operating temperature 0 to 50¡ C (32 to 122¡ F)
Operating humidity 10% to 90% relative humidity, noncondensing
Electromagnetic
compliance FCC Part 15, Class A; EN 55 022 (CISPR 22), VCCI Class A
Safety agency approvals
for the power adapter CE mark, C-Tick
Performance Specifications
Frame filter rate 14,800 frames/sec max for 10M port / 148,000 frames/sec
max for 100M port/1,480,000 frames/sec for 1000M port
Frame forward rate 14,800 frames/sec max for 10M port / 148,000 frames/sec
max for 100M port / 1,480,000 frames/sec max for 1000M
port
Network latency (using
1500-byte packets) 10Mbs: 1250us max 100Mbs: 125us max
1000Mbs: 15us max
Address database size 4000 MAC addresses
Queue buffer 128 KB Embedded
Technical Support
Thank you for selecting NETGEAR products.
After completing the Smart Wizard configuration assistant, locate the serial number on the
bottom label of your product, and use it to register your product at
http://www.NETGEAR.com/register.
Registration on the website or over the phone is required before you can use our telephone
support service. The phone numbers for worldwide regional customer support centers are
on the Warranty and Support Information card that came with your product.
Go to http://kbserver.netgear.com for product updates and Web support.
Statement of Conditions
In the interest of improving internal design, operational function, and/operability, NETGEAR reserves the
right to make changes to the product described in this document without notice. NETGEAR does not
assume any liability that may occur due to the use or application of the product(s) or circuit layout(s)
described herein.