NETGEAR ProSafe GS716T-200 Manual

202-10510-01
June 2009
v1.0
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, California 95134 USA
GS716T/GS724T
Hardware Installation
Guide

ii
v1.0, June 2009
© 2007, 2008, 2009 by NETGEAR, Inc. All rights reserved.
Trademarks
NETGEAR, the NETGEAR logo, and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc.
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Other brand and product
names are registered trademarks or trademarks of their respective holders. Portions of this document are copyright
Intoto, Inc.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the Smart Switch has been suppressed in accordance with the conditions set out in the BMPT-
AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance
with the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating
instructions.
The Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market
and has been granted the right to test the series for compliance with the regulations.
Product and Publication Details
Model Number: GS716T and GS724T
Publication Date: June 2009
Product Family: GS716T/GS724T Series Smart Switch
Product Name: Smart Switch
Home or Business Product: Business
Language: English
Publication Part Number: 202-10510-01
Publication Version Number: 1.0

iii
v1.0, June 2009
Contents
GS716T/GS724T Hardware Installation Guide
About This Manual
Conventions, Formats and Scope .....................................................................................v
Revision History ................................................................................................................ vi
Chapter 1
Introduction
Overview .........................................................................................................................1-1
Features .........................................................................................................................1-2
Package Contents ..........................................................................................................1-3
Chapter 2
Physical Description
GS716T Front and Back Panel Configuration ................................................................2-5
GS724T Front and Back Panel Configuration ................................................................2-6
LED Designations ...........................................................................................................2-7
Port LEDs .................................................................................................................2-7
System LEDs ...........................................................................................................2-8
Device Hardware Interfaces ...........................................................................................2-8
RJ-45 Ports ..............................................................................................................2-8
SFP GBIC Module ....................................................................................................2-9
Factory Defaults Button ............................................................................................2-9
Chapter 3
Applications
Desktop Switching ........................................................................................................3-11
Chapter 4
Installation
Step 1: Preparing the Site .............................................................................................4-13
Step 2: Installing the Switch ..........................................................................................4-14
Installing the Switch on a Flat Surface ...................................................................4-14
Installing the Switch in a Rack ...............................................................................4-14

GS716T/GS724T Hardware Installation Guide
iv
v1.0, June 2009
Step 3: Checking the Installation ..................................................................................4-15
Step 4: Connecting Devices to the Switch ....................................................................4-16
Step 5: Installing an SFP GBIC Module ........................................................................4-16
Step 6: Applying AC Power ..........................................................................................4-17
Step 7: Managing the Switch using a Web Browser or the PC Utility ...........................4-18
Appendix A
Troubleshooting
Troubleshooting Chart ................................................................................................. A-19
Additional Troubleshooting Suggestions ..................................................................... A-20
Network Adapter Cards ......................................................................................... A-20
Configuration ......................................................................................................... A-20
Switch Integrity ...................................................................................................... A-20
Auto-Negotiation ................................................................................................... A-21
Appendix B
Technical Specifications
Index

v
v1.0, June 2009
About This Manual
The NETGEAR®ProSafeTM GS716T/GS724T Hardware Installation Guide describes how to
install, configure and troubleshoot the Smart Switch. The information in this manual is intended
for readers with intermediate computer and Internet skills.
Conventions, Formats and Scope
The conventions, formats, and scope of this manual are described in the following paragraphs:
•Typographical Conventions. This manual uses the following typographical conventions:
•Formats. This manual uses the following formats to highlight special messages:
Italic Emphasis, books, CDs, file and server names, extensions
Bold User input, IP addresses, GUI screen text
Fixed Command prompt, CLI text, code
italic URL links
Note: This format is used to highlight information of importance or special interest.
Tip: This format is used to highlight a procedure that will save time or resources.
Warning: Ignoring this type of note may result in a malfunction or damage to the
equipment.

GS716T/GS724T Hardware Installation Guide
vi
v1.0, June 2009
•Scope. This manual is written for the Smart Switch according to these specifications:
Revision History
Danger: This is a safety warning. Failure to take heed of this notice may result in
personal injury or death.
Product Version Smart Switch
Manual Publication Date June 2009
Note: Product updates are available on the NETGEAR, Inc. website at
http://kbserver.netgear.com/main.asp.
Part Number Version
Number Date Description
202-10510-01 1.0 June 2009 Initial release

1-1
v1.0, June 2009
Chapter 1
Introduction
Congratulations on the purchase of the NETGEAR Smart Switch. The NETGEAR Smart Switch is
a state-of-the-art, high-performance, IEEE-compliant network solution designed for users who
require a large number of ports and want the power of Gigabit connectivity to eliminate
bottlenecks, boost performance, and increase productivity. To simplify installation, the switch is
shipped ready for use out of the box.
This chapter serves as an introduction to the Smart Switch and provides the following information:
•Overview
•Features
•Package Contents
Overview
This Installation Guide is for the following NETGEAR Smart Switches:
• GS716T – This product offers support for 16 ports of 10/100/1000 Mbps and two Form-factor
slots, which support 1000 (1000BASE-SX/LX)/100 Mbps Small Form-factor Pluggable
(SFP).
• GS724T – This product offers support for 24 ports of 10/100/1000 and two Form-factor slots,
which support 1000 (1000BASE-SX/LX)/100 Mbps SFP.
Using Gigabit ports, high-speed connections can be made to a server or network backbone. For
example:
• Linking to high-speed servers
• Providing 10/100/1000 Mbps copper and fiber connectivity
The Smart Switch also provides the benefit of administrative management with a complete
package of features for the observation, configuration, and control of the network. With a Web-
based Graphical User Interface (GUI), the switch’s many capabilities can be viewed and used in a
simple and intuitive manner. The switch’s management features include configuration for port and
switch information, VLAN for traffic control, port trunking for increased bandwidth, and Class of

GS716T/GS724T Hardware Installation Guide
1-2 Introduction
v1.0, June 2009
Service (CoS) for traffic prioritization. These features provide better understanding and control of
the network. Initial discovery of the switch on the network requires the Smart Wizard Discovery
program, a utility that runs on a PC.
The Smart Switch can be free-standing, or rack mounted in a wiring closet or equipment room. It is
IEEE-compliant and offers low latency for high-speed networking. All ports can automatically
negotiate to the highest speed. This capability makes the switch ideal for environments that have a
mix of Ethernet, Fast Ethernet, or Gigabit Ethernet devices. In addition, all RJ-45 ports operate in
half-duplex or full-duplex mode. The maximum segment length is 328 feet (100 meters) over
Category 5 Unshielded Twisted-Pair (UTP) cable, but much longer for fiber connections using
SFP GBIC modules.
Features
The following list identifies the key features of the NETGEAR Smart Switch.
• 16/24 RJ-45 10/100/1000 Mbps auto sensing Giga switching ports.
• 2 Small Form-factor Pluggable (SFP) GBIC slots which function as combo ports. Combo ports
are single ports with two physical connections, SFP fiber and RJ-45 copper. The RJ-45 copper
ports corresponding to the Combo ports are the last four 10/100/1000 Mbps auto sensing Giga
switching ports on each device. If both devices are plugged in, the fiber connection is active,
with fiber port taking priority if both are connected. The following SFP types are supported:
• 1000BASE-SX
• 1000BASE-LX
• 100BASE-FX
• The devices support full NETGEAR Smart Switch functionality.
• The devices provide full compatibility with IEEE standards:
• IEEE 802.3i, (10BASE-T)
• IEEE 802.3u (100BASE-TX, 100BASE-FX)
• IEEE 802.3x (Full-duplex flow control)
• IEEE 802.3ab (1000BASE-T)
• IEEE 802.3z (1000BASE-X)
• Auto-sensing and auto-negotiating capabilities for all ports.
• Auto Uplink™ on all ports to make the right connection.

GS716T/GS724T Hardware Installation Guide
Introduction 1-3
v1.0, June 2009
• Automatic address learning function to build the packet-forwarding information table. The
table contains up to 8K Media Access Control (MAC) addresses.
• Full-duplex and half-duplex functions for all 10/100/1000 Mbps ports.
• Store-and-Forward transmission to remove bad packets from the network.
• Full-duplex IEEE 802.3x pause frame flow control.
• Active flow control to minimize packet loss/frame drops.
• Half-duplex back-pressure control.
• Per port LEDs, System LEDs.
• Standard 1U high, rack-mountable 17-inch chassis.
• Fan speed control supported.
Package Contents
Figure 1-1 shows the package contents of the NETGEAR GS716T and GS724T Series Smart
Switch.
Figure 1-1
MODEL GS724T
ProSafe 24 Port Gigabit Smart Switch
23F 24F
Link/
ACT Link/ ACT
Factory
Defaults
Reset PWR
57911
6810
12
17 19 21 23T
18 20 22 24T
LINK/ACT
SPD
FDX
LINK/ACT
SPD
FDX
18
17
20
19
22
21
24
23
Yellow (100M)
Green (1000M)
Uplink
™
Auto
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
®13
24
13 15
14 16

GS716T/GS724T Hardware Installation Guide
1-4 Introduction
v1.0, June 2009
Verify that the package contains the following:
• NETGEAR Smart Switch
• Rubber footpads for tabletop installation
• Power cord
• Rack-mount kit for installing the switch in a 19-inch rack
• Installation guide
• Smart Switch Resource CD with Smart Wizard Discovery and User’s manual
• Warranty/Support Information Card
If any item is missing or damaged, contact the place of purchase immediately.

2-5
v1.0, June 2009
Chapter 2
Physical Description
This chapter describes the NETGEAR Smart Switch hardware features. Topics include:
•GS716T Front and Back Panel Configuration
•GS724T Front and Back Panel Configuration
•LED Designations
•Device Hardware Interfaces
GS716T Front and Back Panel Configuration
The GS716T is a 24-port 10/100/1000 Mbps + 2 SFP Combo ports Smart Switch. Every RJ-45
port is capable of sensing the line speed and negotiating the operation duplex mode with the link
partner automatically
Figure 2-1 illustrates the NETGEAR GS716T Smart Switch front panel:
The front panel contains the following:
• 16 RJ-45 connectors for 10/100/1000 Mbps auto sensing Gigabit Ethernet switching ports.
• Two SFP slots for SFP modules supporting 1000 (1000BASE-SX/LX)/100 Mbps SFP.
• Reset button to restart the device.
• Recessed default reset button to restore the device back to the factory defaults.
• Port LEDs
Figure 2-1
MODEL GS716T
ProSafe 16 Port Gigabit Smart Switch
15F 16F
Link/
ACT Link/ ACT
Factory
Defaults
Reset PWR
1357
2468
9 11 13 15T
10 12 14 16T
®
LINK/ACT
SPD
FDX
LINK/ACT
SPD
FDX
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
Yellow (100M)
Green (1000M)
Uplink
™
Auto
System LEDs
SFP Ports
10/100/1000 Mbps Ethernet Ports

GS716T/GS724T Hardware Installation Guide
2-6 Physical Description
v1.0, June 2009
• System LEDs
Figure 2-2 illustrates the NETGEAR GS716T Smart Switch back panel:
The back panel contains the following:
• A 100-240VAC/50-60 Hz universal input, which is a standard AC power receptacle for
accommodating the supplied power cord.
GS724T Front and Back Panel Configuration
The GS724T is a 24-port 10/100/1000 Mbps Smart Switch + 2 SFP Combo ports switch. Every
RJ-45 port is capable of sensing the line speed and negotiating the operation duplex mode with the
link partner automatically
Figure 2-3 illustrates the NETGEAR GS724T Smart Switch front panel:
The front panel contains the following:
• 24 RJ-45 connectors for 10/100/1000 Mbps auto-sensing Gigabit Ethernet switching ports.
• Two slots for SFP slots for SFP modules supporting 1000 (1000BASE-SX/LX)/100 Mbps
SFP.
• Reset button to restart the device.
• Recessed default reset button to restore the device back to the factory defaults.
Figure 2-2
Figure 2-3
100-240V ~ 50-60Hz
RS-232 Power Connector
MODEL GS724T
ProSafe 24 Port Gigabit Smart Switch
23F 24F
Link/
ACT Link/ ACT
Factory
Defaults
Reset PWR
57911
6810
12
17 19 21 23T
18 20 22 24T
LINK/ACT
SPD
FDX
LINK/ACT
SPD
FDX
18
17
20
19
22
21
24
23
Yellow (100M)
Green (1000M)
Uplink
™
Auto
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
®13
24
13 15
14 16
System LEDs
SFP Ports
10/100/1000 Mbps Ethernet Ports

GS716T/GS724T Hardware Installation Guide
Physical Description 2-7
v1.0, June 2009
• System LEDs
Figure 2-4 illustrates the NETGEAR GS724T Smart Switch back panel:
The back panel contains the following:
• A 100-240VAC/50-60 Hz universal input, which is a standard AC power receptacle for
accommodating the supplied power cord.
LED Designations
Port LEDs
The following table describes the port LED designations.
Figure 2-4
Table 2-1. Port LEDs
Port LED Designation
16/24-10/100/1000 Mbps
Ports - 3 LEDs per port LINK/ACT SPD
FDX
•Solid Green - A valid 1000 Mbps link is
established on the port.
•Flashing Green - Packet transmission or
reception is occurring on the port at
1000 Mbps.
•Solid Yellow - A valid 10/100 Mbps link is
established on the port.
•Flashing Yellow - Packet transmission or
reception is occurring on the port at 10/
100 Mbps.
•Off - No 10/100 Mbps link is established on
the port.
•Solid Green - Full-duplex link is established
on the port.
•Off - No full-duplex or half-duplex link is
established on the port.
100-240V ~ 50-60Hz
RS-232 Power Connector

GS716T/GS724T Hardware Installation Guide
2-8 Physical Description
v1.0, June 2009
System LEDs
The following table describes the system LED designations.
Device Hardware Interfaces
RJ-45 Ports
RJ-45 ports are auto-sensing ports. When inserting a cable into an RJ-45 port, the switch
automatically ascertains the maximum speed (10, 100, or 1000 Mbps) and duplex mode (half-
duplex or full-duplex) of the attached device. All ports support only unshielded twisted-pair (UTP)
cable terminated with an 8-pin RJ-45 plug.
To simplify the procedure for attaching devices, all RJ-45 ports support Auto Uplink. This
technology allows attaching devices to the RJ-45 ports with either straight-through or crossover
cables. When inserting a cable into the switch’s RJ-45 port, the switch automatically:
• Senses whether the cable is a straight-through or crossover cable.
2 SFP Ports - 1 LED per
port SFP LINK/ACT • Solid Green - A valid 1000 Mbps SFP module link is established on the port.
•Flashing Green - Packets transmission or
reception is occurring on the port at
1000 Mbps.
•Solid Yellow - A valid 100 Mbps SFP
module link is established on the port.
•Flashing Yellow - Packets transmission or
reception is occurring on the port at
100 Mbps.
•Off - No SPD link is established on the port.
Table 2-2. System LEDs
LED Designation
Power LED • Solid Green - Power is supplied to the switch and is operating
normally.
•Off - Power is disconnected.
Table 2-1. Port LEDs (continued)
Port LED Designation

GS716T/GS724T Hardware Installation Guide
Physical Description 2-9
v1.0, June 2009
• Determines whether the link to the attached device requires a “normal” connection (such as
when connecting the port to a PC) or an “uplink” connection (such as when connecting the
port to a router, switch, or hub).
• Configures the RJ-45 port to enable communications with the attached device, without
requiring user intervention. In this way, the Auto Uplink technology compensates for setting
uplink connections, while eliminating concern about whether to use crossover or straight-
through cables when attaching devices.
SFP GBIC Module
The GBIC module bays accommodate standard SFP GBIC modules, such as the AGM731F,
AGM732F, or AGM733 from NETGEAR, allowing fiber connections on the network. The module
bay is a combo port, sharing a connection with an RJ-45 port. Being a combo port, only one type
of connection can be active at any given time. For example, both copper and fiber port cannot be
used at the same time. If both connectors are plugged in at the same time, the fiber port will be
active.
The SFP GBIC bay accommodates a standard SFP GBIC module.
Factory Defaults Button
The Smart Switch has a Factory Default button so that you can remove the current configuration
and return the device to its factory settings. When you enable the Factory Default button, all
settings, including the password, VLAN settings and port configurations will be removed.

3-11
v1.0, June 2009
Chapter 3
Applications
Your NETGEAR Smart Switch is designed to provide flexibility in configuring your network
connections. It can be used as a stand-alone device or with 10 Mbps, 100 Mbps, and 1000 Mbps
hubs and switches.
Desktop Switching
The NETGEAR Smart Switch can be used as a desktop switch to build a small network that
enables users to have 1000 Mbps access to a file server. With full-duplex enabled, the switch port
connected to the server or PC can provide 2000 Mbps throughput.
Figure 3-1

4-13
v1.0, June 2009
Chapter 4
Installation
This chapter describes the installation procedures for your NETGEAR Smart Switch. Switch
installation involves the following steps:
Step 1: Preparing the Site
Step 2: Installing the Switch
Step 3: Checking the Installation
Step 4: Connecting Devices to the Switch
Step 5: Installing an SFP GBIC Module
Step 6: Applying AC Power
Step 7: Managing the Switch using a Web Browser or the PC Utility
Step 1: Preparing the Site
Before you installing the switch, ensure the operating environment meets the operating
environment requirements in the following table.
Table 4-1. Site Requirements
Characteristics Requirements
Mounting • Desktop installations - Provide a flat table or shelf surface.
•Rack-mount installations - Use a 17-inch (48.3-centimeter) EIA standard equipment
rack that is grounded and physically secure. The rack-mount kit supplied with the switch
is also required.
Access Locate the switch in a position that allows access to the front panel RJ-45 ports, view the
front panel LEDs, and access power connector.

GS716T/GS724T Hardware Installation Guide
4-14 Installation
v1.0, June 2009
Step 2: Installing the Switch
The NETGEAR Smart Switch can be installed on a flat surface or in a standard 19-inch rack.
Installing the Switch on a Flat Surface
The switch ships with four self-adhesive rubber footpads. Stick one rubber footpad on each of the
four concave spaces on the bottom of the switch. The rubber footpads cushion the switch against
shock/vibrations.
Installing the Switch in a Rack
To install the switch in a rack, use the following procedure (and refer to Figure 4-1). To perform
this procedure, the 17-inch rack-mount kit supplied with switch is required.
1. Attach the supplied mounting brackets to the side of the switch.
2. Insert the screws provided in the rack-mount kit through each bracket and into the bracket
mounting holes in the switch.
3. Tighten the screws with a #1 Phillips screwdriver to secure each bracket.
4. Align the mounting holes in the brackets with the holes in the rack, and insert two pan-head
screws with nylon washers through each bracket and into the rack.
Power source Provide a power source within 6 feet (1.8 meters) of the installation location. Power
specifications for the switch are shown in Appendix A . Ensure the AC outlet is not
controlled by a wall switch, which can accidentally turn off power to the outlet and the
switch.
Environmental • Temperature - Install the switch in a dry area, with ambient temperature between 0 and
55ºC (32 and 131ºF). Keep the switch away from heat sources such as direct sunlight,
warm air exhausts, hot-air vents, and heaters.
•Operating humidity - The installation location should have a maximum relative
humidity of 90%, non-condensing.
•Ventilation - Do not restrict airflow by covering or obstructing air inlets on the sides of
the switch. Keep at least 2 inches (5.08 centimeters) free on all sides for cooling. Be
sure there is adequate airflow in the room or wiring closet where the switch is installed.
•Operating conditions - Keep the switch at least 6 ft. (1.83 m) away from nearest
source of electromagnetic noise, such as a photocopy machine.
Table 4-1. Site Requirements (continued)
Characteristics Requirements

GS716T/GS724T Hardware Installation Guide
Installation 4-15
v1.0, June 2009
5. Tighten the screws with a #2 Phillips screwdriver to secure the switch in the rack.
Step 3: Checking the Installation
Before applying power perform the following:
• Inspect the equipment thoroughly.
• Verify that all cables are installed correctly.
• Check cable routing to make sure cables are not damaged or creating a safety hazard.
• Ensure all equipment is mounted properly and securely.
Figure 4-1

GS716T/GS724T Hardware Installation Guide
4-16 Installation
v1.0, June 2009
Step 4: Connecting Devices to the Switch
The following procedure describes how to connect PCs to the switch’s RJ-45 ports. The
NETGEAR Smart Switch contains Auto Uplink™ technology, which allows the attaching of
devices using either straight-through or crossover cables.
Connect each PC to an RJ-45 network port on the Switch front panel (Figure 4-2 ). Use Category 5
(Cat5) Unshielded Twisted-Pair (UTP) cable terminated with an RJ-45 connector to make these
connections.
Step 5: Installing an SFP GBIC Module
The following procedure describes how to install an SFP Gigabit Ethernet module in the switch’s
Gigabit module bay. Standard SFP GBIC modules are sold separately from the Smart Switch. If an
SFP GBIC module is not being installed at this time, skip this procedure.
To install an SFP GBIC module:
Figure 4-2
Note: Ethernet specifications limit the cable length between the switch and the attached
device to 100 m (328 ft.).