NETGEAR MS510TX User manual

350 East Plumeria Drive
San Jose, CA 95134
USA
September 2017
202-11762-02
8-Port Multi-Gigabit
Smart Managed Pro Switch
with Two 10G Ports
MS510TX and MS510TXPP
User Manual

2
Smart Managed Pro Switches MS510TX and MS510TXPP
Support
Thank you for purchasing this NETGEAR product. You can visit www.netgear.com/support to register your product, get help,
access the latest downloads and user manuals, and join our community. We recommend that you use only official NETGEAR
support resources.
Conformity
For the current EU Declaration of Conformity, visit http://kb.netgear.com/app/answers/detail/a_id/11621.
Compliance
For regulatory compliance information, visit http://www.netgear.com/about/regulatory.
See the regulatory compliance document before connecting the power supply.
Trademarks
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non-NETGEAR trademarks are
used for reference purposes only.
Revision History
Publication Part Number Publish Date Comments
202-11762-02 September 2017 Made minor changes and corrections.
202-11762-01 September 2017 First publication.

3
Contents
Chapter 1 Get Started
Switch Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Available Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Switch Management Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Web Browser Requirements and Supported Browsers . . . . . . . . . . . . . . . . . . . . 11
User-Defined Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Interface Naming Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Access the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Access the Switch On-Network With a DHCP Server. . . . . . . . . . . . . . . . . . . 13
Access the Switch On-Network Without a DHCP Server. . . . . . . . . . . . . . . . 15
Access the Switch Off-Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Register the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
How to Configure Interface Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Local Browser Interface Device View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Chapter 2 Configure System Information
View and Configure the Switch Management Settings . . . . . . . . . . . . . . . . . . . . 24
View or Define System Information and View Software Versions . . . . . . . . 24
View the System CPU Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
View USB Device Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Configure the IPv4 Address for the Network Interface and
Management VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Configure the IPv6 Address for the Network Interface . . . . . . . . . . . . . . . . . 30
View the IPv6 Network Neighbor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Configure the Time Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Configure DNS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Configure Green Ethernet Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Use the Device View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Configure Power over Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
PoE Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Device Class Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Power Allocation and Power Budget . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Configure the Global PoE Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Manage and View the PoE Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 55
Configure SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Configure the SNMPv1/v2 Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Configure SNMPv1/v2 Trap Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Configure SNMPv1/v2 Trap Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
View the Supported MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

4
Smart Managed Pro Switches MS510TX and MS510TXPP
Configure SNMPv3 Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Configure LLDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Configure LLDP Global Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Configure LLDP Port Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
LLDP-MED Network Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
LLDP-MED Port Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Local Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Neighbors Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Configure DHCP Snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Configure the Global DHCP Snooping Settings . . . . . . . . . . . . . . . . . . . . . . . . 76
Enable DHCP for All Interfaces in a VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Configure DHCP Snooping Interface Settings . . . . . . . . . . . . . . . . . . . . . . . . . 77
Configure Static DHCP Bindings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Configure the DHCP Snooping Persistent Settings . . . . . . . . . . . . . . . . . . . . . 80
Set Up PoE Timer Schedules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Create a PoE Timer Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Specify the Settings for a PoE Timer Schedule . . . . . . . . . . . . . . . . . . . . . . . . 82
Add a Periodic Schedule for a PoE Timer Schedule . . . . . . . . . . . . . . . . . . . . . 83
Delete a Periodic Schedule for a PoE Timer Schedule . . . . . . . . . . . . . . . . . . . 84
Delete a PoE Timer Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Chapter 3 Configure Switching
Configure Port Settings and Flow Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Configure IEEE 802.3x Global Flow Control. . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Configure the Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Configure Link Aggregation Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Configure LAG Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Configure LAG Membership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Set the LACP System Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Set the LACP Port Priority Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Configure VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Configure VLAN Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Configure VLAN Membership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
View VLAN Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Configure Port PVID Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Configure MAC-Based VLAN Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Manually Add Members to or Remove Them From a MAC-Based
VLAN Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Configure Protocol-Based VLAN Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Manually Add Members to or Remove Them From a
Protocol-Based VLAN Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Configure GARP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Configure GARP Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Configure a Voice VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Configure the Global Voice VLAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Configure Membership for the Voice VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Manage the OUI Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

5
Smart Managed Pro Switches MS510TX and MS510TXPP
Configure Auto-VoIP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Configure Spanning Tree Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Configure STP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Configure CST Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Configure CST Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
View the CST Port Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
View Rapid STP Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Manage MST Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Configure MST Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
View STP Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Configure Multicast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
View the MFDB Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
View the MFDB Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Configure Auto-Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
IGMP Snooping Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Configure the Global IGMP Snooping Settings. . . . . . . . . . . . . . . . . . . . . . . . 134
View the IGMP Snooping Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Configure IGMP Snooping for VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Modify IGMP Snooping Settings for a VLAN . . . . . . . . . . . . . . . . . . . . . . . . . 137
Disable IGMP Snooping on a VLAN and Remove It From the Table . . . . . . . 138
IGMP Snooping Querier Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Configure IGMP Snooping Querier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Configure IGMP Snooping Querier for VLANs . . . . . . . . . . . . . . . . . . . . . . . . 140
Display the IGMP Snooping Querier for VLAN Status . . . . . . . . . . . . . . . . . . 141
MLD Snooping Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Configure the Global MLD Snooping Settings . . . . . . . . . . . . . . . . . . . . . . . . 142
Configure MLD Snooping for a VLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Configure a Multicast Router Interface on a VLAN . . . . . . . . . . . . . . . . . . . . 144
Configure MLD Snooping Querier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Configure MLD Snooping Querier VLAN Settings . . . . . . . . . . . . . . . . . . . . . 146
Configure a Multicast Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Remove a Multicast Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Configure Multicast Group Membership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Configure the Multicast Forward All Option . . . . . . . . . . . . . . . . . . . . . . . . . . 150
View, Search, and Manage the MAC Address Table . . . . . . . . . . . . . . . . . . . . . . 151
View and Search the MAC Address Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Change the Aging-Out Period of Dynamic MAC Addresses. . . . . . . . . . . . . 153
Add a Static MAC Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Remove a Static MAC Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Chapter 4 Configure Routing
IP Routing Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Configure IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Configure the Routing Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
View the IP Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Configure VLAN Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Use the VLAN Static Routing Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
VLAN Routing Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

6
Smart Managed Pro Switches MS510TX and MS510TXPP
Manage IPv4 Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Configure Address Resolution Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Display the ARP Cache . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Add an Entry to the ARP Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Configure the Global Aging-Out Time for ARP . . . . . . . . . . . . . . . . . . . . . . . 169
Remove an ARP Entry From the ARP Cache . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Configure IPv6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Configure IPv6 Global Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Add a Static IPv6 Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Change the Preference for a Static IPv6 Route . . . . . . . . . . . . . . . . . . . . . . . 173
Remove a Static IPv6 Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
View the IPv6 Route Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Configure IPv6 VLAN Interface Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Add an IPv6 Global Address to an IPv6 VLAN . . . . . . . . . . . . . . . . . . . . . . . . 178
Change the Settings for an IPv6 Global Address on an IPv6 VLAN. . . . . . . 180
Remove an IPv6 Global Address From an IPv6 VLAN . . . . . . . . . . . . . . . . . . 181
Add an IPv6 Prefix for Advertisement on an IPv6 VLAN . . . . . . . . . . . . . . . 181
Change the Settings for an IPv6 Prefix for Advertisement on
an IPv6 VLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Remove an IPv6 Prefix From an IPv6 VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . 183
View IPv6 Statistics for an Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
View or Clear the IPv6 Neighbor Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Chapter 5 Configure Quality of Service
Manage Class of Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
CoS Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Configure Global CoS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
Configure CoS Interface Settings for an Interface . . . . . . . . . . . . . . . . . . . . 190
Configure the Global CoS Queue Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Configure the Global 802.1p to Queue Mapping . . . . . . . . . . . . . . . . . . . . . 193
DSCP to Queue Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Manage Differentiated Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
DiffServ Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
View the Global DiffServ Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Specify DSCP Remark Values for Violate Action IP Packets. . . . . . . . . . . . . 197
Configure IPv4 DiffServ Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Configure an IPv6 DiffServ IPv6 Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Configure a DiffServ Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Configure DiffServ Service Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
View DiffServ Service Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
Chapter 6 Manage Device Security
Management Security Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Change the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Reset the Password to the Factory Default Value . . . . . . . . . . . . . . . . . . . . . 217
Configure RADIUS Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
Configure TACACS+ Servers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224

7
Smart Managed Pro Switches MS510TX and MS510TXPP
Configure Authentication Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
Configure Management Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Configure HTTP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Configure HTTPS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Manage the Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
Configure Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Configure Port Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
Configure Global 802.1X Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
Manage Port Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
View the Port Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
View the Client Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Set Up Traffic Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Configure Storm Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Configure Port Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
Configure Protected Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Configure Private VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Configure Access Control Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
Use the ACL Wizard to Create a Simple ACL. . . . . . . . . . . . . . . . . . . . . . . . . . 259
Configure a Basic MAC ACL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
Configure MAC ACL Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266
Configure MAC Bindings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
View or Delete MAC ACL Bindings in the MAC Binding Table . . . . . . . . . . . 271
Configure an IP ACL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
Configure Rules for a Basic IP ACL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Configure Rules for an Extended IP ACL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
Configure an IPv6 ACL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Configure IPv6 Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Configure IP ACL Interface Bindings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
View or Delete IP ACL Bindings in the IP ACL Binding Table. . . . . . . . . . . . . 288
Chapter 7 Monitor the System
Monitor the Switch and the Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
Switch Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
View Port Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292
View Detailed Port Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
View EAP Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
Perform a Cable Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
Configure and View Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
Manage the Buffered Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
Manage the Flash Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
Manage the Server Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
View the Trap Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
Configure Port Mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
View the System Resource Utilization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
Chapter 8 Maintain the Switch and Perform Troubleshooting
Reboot the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312

8
Smart Managed Pro Switches MS510TX and MS510TXPP
Reset the Switch to Its Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . 312
Export a File From the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
Export a File to the TFTP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
HTTP File Export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
Export a File From the Switch to a USB Device . . . . . . . . . . . . . . . . . . . . . . . 316
Download a File to the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
Download a File to the Switch Using TFTP . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
Download a File to the Switch Using HTTP . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
Download a File From a USB Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
Manage Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
Change the Image That Loads During the Boot Process. . . . . . . . . . . . . . . . 321
View the Dual Image Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
Ping an IPv4 Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
Ping an IPv6 Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
Send an IPv4 Traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326
Send an IPv6 Traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
Generate Technical Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
Enable Remote Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
Appendix A Configuration Examples
Virtual Local Area Networks (VLANs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
VLAN Configuration Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
Access Control Lists (ACLs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
Sample MAC ACL Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
Sample Standard IP ACL Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334
Differentiated Services (DiffServ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335
Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
DiffServ Traffic Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
Creating Policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337
DiffServ Example Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
802.1X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
802.1X Example Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341
MSTP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
MSTP Example Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344
VLAN Routing Interface Configuration Example. . . . . . . . . . . . . . . . . . . . . . . . . 346
Appendix B Hardware Specifications and Default Settings
Hardware Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348
Switch Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349

9
1
1. Get Started
This manual describes how you can configure and monitor the following NETGEAR switches by
using the local browser–based management interface:
•MS510TX. 8-Port Multi-Gigabit Smart Managed Pro Switch with two 10G Ports, Model
MS510TX
•MS510TXPP. 8-Port Multi-Gigabit Smart Managed Pro Switch with PoE+ and two 10G
Ports, Model MS510TXPP
This chapter contains the following sections:
•Switch Descriptions
•Available Publications
•Switch Management Methods
•Web Browser Requirements and Supported Browsers
•User-Defined Fields
•Interface Naming Conventions
•Access the Switch
•Register the Switch
•How to Configure Interface Settings
•Local Browser Interface Device View
In this manual, we refer to both switch models as the switch. Unless noted otherwise, all
information applies to both switch models.
For more information about the topics covered in this manual, visit the support website at
netgear.com/support.
Firmware updates with new features and bug fixes are automatically made available through the
Insight app and, if selected, pushed straight from the cloud to the device. If you are not using the
Insight app to manage your device, you can manually download and install the latest firmware by
visiting downloadcenter.netgear.com. If the features or behavior of your product does not match
what is described in this manual, you might need to update your firmware.

Get Started
10
Smart Managed Pro Switches MS510TX and MS510TXPP
Switch Descriptions
The switch provides four multispeed Gigabit Ethernet and four 1G Ethernet RJ-45 copper
ports with one dedicated 10G RJ-45 copper uplink port and one dedicated SFP+ fiber uplink
port that supports 10G and 1G. Two of the four multispeed ports support 5G, 2.5G, and 1G.
The other two multispeed ports support 2.5G and 1G. (The 10G RJ-45 copper uplink port also
supports 5G, 2.5G and 1G.)
The switch models differ in the following ways:
•Model MS510TXPP. This model supports Power over Ethernet plus (PoE+) on all four
multispeed ports and four 1G ports so that you can let the switch provide power to
PoE-capable devices such as WiFi access points, VoIP phones, and IP security cameras.
•Model MS510TXPP.This model can supply up to 30W PoE+ (IEEE 802.3at) to each port,
with a maximum PoE power budget of 180W across all active PoE+ ports.
Available Publications
The following guides and manual are available at downloadcenter.netgear.com:
•Installation Guide
•Hardware Installation Guide
•Smart Control Center User Manual
For general switch information, see the NETGEAR knowledge base articles at
netgear.com/support.
Switch Management Methods
If you prefer, you can use the switch as a plug-and-play device, so you do not need to set up
a custom configuration. Just connect power, connect to your network and to your other
devices, and you are done.
You can configure the switch and the network, including the ports, the management VLAN,
VLANs for traffic control, link aggregation for increased bandwidth, quality of service (QoS)
for prioritizing traffic, and network security.
You can configure and monitor the switch by using one of the following methods:
•Smart Control Center (SCC). Initial discovery of the switch on the network requires the
Smart Control Center (SCC) program, which runs on a Windows-based computer and is
included on the resource CD. You can also download the SCC program from
downloadcenter.netgear.com. If you do not use a Windows-based computer, get the IP
address of the switch from the DHCP server in the network or use an IP scanner utility.
After discovery, you can configure the switch using the local browser–based management
interface, or the SCC program for very basic setup. For more information, see Access the
Switch on page 12 and the SCC user manual, which you can download from
downloadcenter.netgear.com.

Get Started
11
Smart Managed Pro Switches MS510TX and MS510TXPP
•Local browser–based management interface. This manual describes how to use the
local browser–based management interface, in this manual referred to as the local
browser interface, to manage and monitor the switch. The local browser interface lets you
configure basic and advanced features. For more information, see Access the Switch on
page 12.
•Simple Network Management Protocol (SNMP). You can manage through switch
through SNMP. For more information, see Configure SNMP on page 57.
Web Browser Requirements and Supported Browsers
To access the switch by using a web browser, the browser must meet the following software
requirements:
•HTML version 4.0, or later
•HTTP version 1.1, or later
•Java Runtime Environment 1.6 or later
The following browsers were tested and support the local browser interface. Later browser
versions might function fine but were not tested. The following web browsers are supported:
•Microsoft Internet Explorer (IE) versions 9–11
•Microsoft Edge 25
•Mozilla Firefox versions 53–54
•Chrome versions 58–59
•Safari on MAC OS: 10.1 (MAC OS Yosemite Version 10.10.5)
User-Defined Fields
User-defined fields can contain 1 to 159 characters, unless otherwise noted on the
configuration web page. All characters can be used except for the ones stated in the
following table (unless specifically noted in a procedure for a feature).
Table 1. Invalid characters for user-defined fields
Invalid characters for user-defined fields
\<
/>
*|
?

Get Started
12
Smart Managed Pro Switches MS510TX and MS510TXPP
Interface Naming Conventions
The switch supports physical and logical interfaces. Interfaces are identified by their type and
the interface number. The physical ports are Gigabit interfaces and are numbered on the front
panel. You configure the logical interfaces by using the local browser interface.
The following types of ports are supported:
•Ports g1-g4 are Gigabit ports.
•Ports mg5-mg6 are Multi-Gigabit Ethernet ports, each of which supports a maximum
speed of 2.5 Gbps.
•Ports mg7-mg8 are Multi-Gigabit Ethernet ports, each of which supports a maximum
speed of 5 Gbps.
•Port xmg9 is a Multi-Gigabit Ethernet port that supports a maximum speed of 10 Gbps.
•Port xg10 is a fiber port in which you can install an SFP+ module.
The following table describes the naming convention for all interfaces on the switch.
Access the Switch
For easiest access, we recommend that you connect the switch to a network with a router or
DHCP server that assigns IP addresses, power on the switch, and then use a computer that
is connected to the same network as the switch (see Access the Switch On-Network With a
DHCP Server on page 13). If your network does not include a DHCP server, you can assign a
static IP address (see Access the Switch On-Network Without a DHCP Server on page 15).
It is also possible to configure the switch connected directly only to the computer that you are
using to configure it, and not connected to the network (off-network, see Access the Switch
Off-Network on page 16).
Use one of the following methods to determine or assign the IP address of the switch and
access the switch:
•Determine the DHCP-assigned IP address. DHCP is enabled on the switch by default.
If you connect the switch to a network with a DHCP server, the switch obtains its network
information automatically. You can use the Smart Control Center to discover the
Table 2. Naming conventions for interfaces
Interface Description Examples
Physical The physical ports are numbered sequentially
starting from one. g1, g2, mg5,
xmg9
xg10
Link aggregation group (LAG) LAG interfaces are logical interfaces that are
used only for bridging functions. LAG1, LAG2, LAG8
Routing VLAN interfaces An interface is used for routing functionality. VLAN 1, VLAN 2, VLAN 55

Get Started
13
Smart Managed Pro Switches MS510TX and MS510TXPP
automatically assigned network information. For more information, see Access the Switch
On-Network With a DHCP Server on page 13.
•Assign a static IP address through the Smart Control Center. If you connect the
switch to a network that does not include a DHCP server, or you prefer to assign static
addresses, you can use the Smart Control Center (SCC) to assign a static IP address,
subnet mask, and default gateway. For more information, see Access the Switch
On-Network Without a DHCP Server on page 15.
•Assign a static IP address from a directly-connected computer. If you do not use the
Smart Control Center to assign a static address, you can connect to the switch directly
from a computer in the 192.168.0.0/24 network and change the settings by using the local
browser interface on the switch. For more information, see Access the Switch
Off-Network on page 16.
Access the Switch On-Network With a DHCP Server
The DHCP client on the switch is enabled by default, allowing a DHCP server on the network
(or router that functions as a DHCP server) to assign an IP address to the switch.
When you connect the switch to your network, the DHCP server automatically assigns an IP
address to the switch. Use the Smart Control Center (SCC) to discover the IP address
automatically assigned to the switch.
The SCC program runs on a Windows-based computer and is included on the resource CD.
You can also download the SCC program from downloadcenter.netgear.com. If you do not
use a Windows-based computer, get the IP address of the switch from the DHCP server in
the network or use an IP scanner utility, which are available free of charge on the Internet.
Note: The computer that is running the SCC program must be on the same
network (that is, in the same broadcast domain) as the switch.
To determine the DHCP-assigned IP address of the switch and access the switch:
1. Connect the switch to a network that includes a DHCP server.
2. Power on the switch by connecting its power cord.
3. Install the Smart Control Center on your computer.
4. Start the Smart Control Center.
5. Click the Discover button.
The Smart Control Center finds your switch.

Get Started
14
Smart Managed Pro Switches MS510TX and MS510TXPP
6. Write down the displayed IP address assigned by the DHCP server.
You need this address later to access the switch directly from a web browser (without
using the Smart Control Center).
7. Select the switch by clicking the row for the switch.
8. Click the Web Browser Access button.
The Smart Control Center launches a browser.
The login window opens.
9. Enter the switch’s password in the Password field.
The default password is password.
The Switch Information page displays. You can now configure the switch.

Get Started
15
Smart Managed Pro Switches MS510TX and MS510TXPP
Access the Switch On-Network Without a DHCP Server
You can use the Smart Control Center (SCC) to set up your switch in a network without a
DHCP server and assign a static IP address to the switch.
If you prefer, you can assign the switch a static IP address even if your network does include
a DHCP server.
The SCC program runs on a Windows-based computer and is included on the resource CD.
You can also download the SCC program from downloadcenter.netgear.com. If you do not
use a Windows-based computer, see Access the Switch Off-Network on page 16.
To assign a static IP address to the switch on-network and access the switch:
1. Connect the switch to a network.
2. Power on the switch by connecting its power cord.
3. Install the Smart Control Center on your computer.
4. Start the Smart Control Center.
5. Click the Discover button.
The Smart Control Center finds your switch.
6. Select the switch, and then click the Configure Device button.
The page expands to display additional fields at the bottom.
7. Select the Disabled radio button.
The DHCP client is disabled.

Get Started
16
Smart Managed Pro Switches MS510TX and MS510TXPP
8. Enter the static switch IP address, gateway IP address, and subnet mask for the switch.
9. Enter the switch password to continue with the configuration change.
The default password is password. You must enter the password each time that you use
the Smart Control Center to update the switch settings.
Note: If you change the default password to a custom password (which we
recommend) using the local browser interface and need to use the
Smart Control Center again, you must enter the custom password for
configuration changes to be accepted.
10. Click the Apply button.
Your settings are saved.
11. Click the Discover button.
The Smart Control Center finds your switch with its new IP address.
12. Select the switch by clicking the row for the switch.
13. Click the Web Browser Access button.
The Smart Control Center launches a browser.
The login window opens.
14. Enter the switch’s password in the Password field.
The default password is password.
The Switch Information page displays. You can now configure the switch.
Access the Switch Off-Network
You can connect to the switch directly from a computer and change the settings by using the
local browser interface of the switch. The default IP address of the switch is 192.168.0.239.
The IP address of the computer that you use to access the switch must in the same subnet
as the default IP address of the switch, that is, it must be in the in the 192.168.0.0/24 subnet.
To assign a static IP address to the switch off-network from a directly-connected
computer:
1. Record your computer’s TCP/IP configuration settings, and then configure the computer
with a static IP address.

Get Started
17
Smart Managed Pro Switches MS510TX and MS510TXPP
For example, configure 192.168.0.210 as the IP address and 255.255.255.0 as the
subnet mask.
Note: Ifyouareunsurehowtodothis,visitnetgear.com/search-support.aspx
and search for the following:
How to set a static IP address in Windows
or
Setting a static IP address on your network adapter in Mac OS
2. Plug the switch into a power outlet and then connect your computer to the switch using an
Ethernet cable.
You can connect the Ethernet cable to any Ethernet port on the switch.
3. Open a web browser, and enter http://192.168.0.239.
This is the default address of the switch.
The login window opens.
4. Enter the switch’s password in the Password field.
The default password is password.
The Switch Information page displays. You can now configure the switch.
5. After you complete the configuration of the switch, reconfigure the computer that you used
for this process to its original TCP/IP settings.
You can now connect your switch to your network using an Ethernet cable.
Register the Switch
To qualify for product updates and product warranty, we encourage you to register your
product. The first time you log in to the switch, you are given the option of registering with
NETGEAR. Registration confirms that your email alerts work, lowers technical support
resolution time, and ensures that your shipping address accuracy. We would also like to
incorporate your feedback into future product development. We never sell or rent your email
address and you can opt out of communications at any time.
When you log in to the switch, you are prompted to register with NETGEAR. However, at any
time you can visit the NETGEAR website for registration at
https://my.netgear.com/register/register.aspx.
How to Configure Interface Settings
For some features that allow you to configure interface settings, you can apply the same
settings simultaneously to any of the following:
•A single port
•Multiple ports

Get Started
18
Smart Managed Pro Switches MS510TX and MS510TXPP
•All ports
•A single LAG
•Multiple LAGs
•All LAGs
•Multiple ports and LAGs
•All ports and LAGs
Many of the pages that allow you to configure or view interface settings include links to
display all ports, all LAGs, or all ports and LAGs on the page.
Use these links as follows:
•To display all ports, click the PORTS link.
•To display all LAGs, click the LAGS link.
•To display all ports and LAGs, click the All link.
The procedures in this section describe how to select the ports and LAGs to configure. The
procedures assume that you are already logged in to the switch. If you do not know how to
log in to the switch, see Access the Switch on page 12.
To configure a single port or LAG:
1. Click the All link to display the all ports and LAGs.
2. Do one of the following:
a. In the Go To Interface field, type the port number and click the Go button.
For example, type g4 for a port or type LAG2 for a LAG. For more information, see
Interface Naming Conventions on page 12.
The check box for the interface is selected, the row for the selected interface is
highlighted, and the interface number displays in the heading row.
b. Select the check box for the port or LAG.
The row for the selected interface is highlighted, and the interface number displays in
the heading row.
3. Configure the desired settings.
4. Click the Apply button.
Your settings are saved.
To configure multiple ports and LAGs:
1. Click the All link to display all ports and LAGs.
2. Select the check box next to each port and LAG to configure.
The row for each selected interface is highlighted.

Get Started
19
Smart Managed Pro Switches MS510TX and MS510TXPP
3. Configure the desired settings.
4. Click the Apply button.
Your settings are saved.
To configure all ports and LAGs:
1. Click the All link to display all ports and LAGs.
2. Select the check box in the heading row.
The check boxes for all ports and LAGs are selected and the rows for all ports and LAGs
are highlighted.
3. Configure the desired settings.
4. Click the Apply button.
Your settings are saved.
Local Browser Interface Device View
The Device View displays the ports in the local browser interface displays the ports on the
switch. This graphic provides an alternate way to navigate to configuration and monitoring
options. The graphic also provides information about device ports, current configuration and
status, tables, and feature components.
To use the Device View:
1. Connect your computer to the same network as the switch.
You can use a WiFi or wired connection to connect your computer to the network, or
connect directly to a switch that is off-network using an Ethernet cable.
2. Launch a web browser.
3. In the address field of your web browser, enter the IP address of the switch.
If you do not know the IP address of the switch, see Access the Switch on page 12.
The login window opens.
4. Enter the switch’s password in the Password field.
The default password is password.
The Switch Information page displays.
5. Select System > Device View.
The previous figure shows the Device View page for model MS510TX.

Get Started
20
Smart Managed Pro Switches MS510TX and MS510TXPP
The system LEDs are located on the left side.
Depending upon the status of the port, the port color in Device View is either yellow,
green, or black (that is, off).
The following table describes the LEDs on the Device View page.
Table 3. LEDs on the Device View page
LED Description
Power LED The Power LED is a bicolor LED that serves as an indicator of power and
diagnostic status:
• Solid green. Power is supplied to the switch and the switch is
operating normally.
• Solid yellow. The switch is in the boot-up stage.
• Off. No power is supplied to the switch.
Fan LED The Fan LED indicates the following status:
• Off. Fan is operating normally.
• Solid yellow. A problem occurred with the fan.
PoE MAX LED
(Model MS510TXPP only) The PoE MAX Power LED indicates the following PoE conditions at switch (not port) level:
• Off. More than 7W of PoE power is available for another powered
device (PD).
• Solid yellow. Less than 7W of PoE power is available for another
PD.
• Blinking yellow. The PoE Max LED was activate in the previous two
minutes.
1G Ports 1–4, Left LEDs
Link, speed, and activity The left LEDs for ports 1–4 (g1 to g4) indicate the following status:
• Off. No link is established.
• Solid green. A valid 1 Gbps link is established.
• Blinking green. The port is transmitting or receiving packets at
1 Gbps.
• Solid yellow. A valid 10 Mbps or 100 Mbps link is established.
• Blinking yellow.The port is transmitting or receiving packets at 10
Mbps or 100 Mbps.
1G Ports 1–4, Right LEDs
PoE status
(Model MS510TXPP only)
The right LEDs for ports 1–4 (g1 to g4) indicate the following status:
• Off. The port is not delivering PoE.
• Solid green. The port is delivering PoE.
• Solid yellow. A PoE fault occurred.
2.5G Ports 5 and 6, Left LEDs
Link, speed, and activity The left LEDs for ports 5 and 6 (mg5 and mg6) indicate the following status:
• Off. No link is established.
• Solid green. A valid 2.5 Gbps link is established.
• Blinking green. The port is transmitting or receiving packets at 2.5
Gbps.
• Solid yellow. A valid 100 Mbps or 1000 Mbps link is established.
• Blinking yellow. The port is transmitting or receiving packets at 100
Mbps or 1000 Mbps.