Newall DP500 User manual

DP500 Quick Start Guide
Technical Specification
For the complete manual please download from:
http://newall.com , Click Technical Support to access the download page.
Environmental
Operating Temperature Storage Temperature
-10°C to 50°C -20 to 70°C
Environmental Con itions - IP40 (Stand Alone)
Relative Humi ity - maximum 95% for temperature up to 31°C
Disposal
At the end of it’s life, you should dispose of the DP500 in a safe
manner applicable to electronic goods.
The case work is suitable for recycling. Please consult local
regulations on disposal.
DP5001016ENUS
023-82110-U /0
Connections
Electrical
EU Directive 73/23/EEC (Low Voltage
Directive)
BS EN 55022:1998 Class B
BS EN 55024:1998
Input to Power Supply Unit (Supplie )
100-240V (47-63Hz)
External switch-mo e
Output voltage 15VDC
Input Voltage to DP500
15-24VDC ±10%
Conforms to Low Voltage Directive
External PSU Input
Note: Newall Measurements Systems reserves the right to change specifications without notice.
Warnings
The mains supply is connected into a switch mode power supply (separate from your DP500) via a
detachable supply cord supplied. If another supply cord is used, it must have fitted a C5, 10A, EARTHED
mains connector with a cord rated for at least 10A.
If a mains plug is not already fitted to the supply cord or is of the wrong type, then a suitable EARTHED plug
should be used which complies with the relevant specifications for plugs and socket-outlets.
You can only use the DP500 with Newall Spherosyn LT and Microsyn LT analogue encoders.
Unit only to be serviced by Newall qualified personnel or authorised alternatives.
If a Spherosyn LT encoder travels over 2.2m an error message will be displayed, see full manual for details.
Turn off the power by disconnecting the power supply connector before you connect the encoder(s)
Cabinet equipotential terminal
for grounding to machine
Cable Clamp
Encoder Input
Connection 2 or 3
According to Model
Technology Gateway, Cornwall Road South
Wigston, Leicester LE18 4XH
United Kingdom
Tel: [phone]
[email protected].uk
www.newall.co.uk
USA
Tel: [phone]
People's Republic of China
Tel: [phone]
Singapore
Tel: [phone]
Japan
Tel: [phone]
For more information about this or any of our products
please contact us at [email protected] or visit www.newall.com

SETTING UP THE UNIT
setup
l a n g u a g e
Understanding the Keypad
Default Settings Optional Settings
Eng gb Eng US afr.
Preset an Axis
=
Microsyn LT
Must be set to match encoders on the machine
*
*Lathe version, X axis set to DIA as default
Message
Display
Axis Selection ey
Numeric eys
Enter ey
Clear Numeric Entry
Center Find
Undo ey
Digifind / Reference
Switches between Zero
and Axis Preset modes
Switches between Absolute
and Incremental modes
Information selection (scrolls
through options on Message
display)
Function Menu ey
Function Navigation eys
Switches between Inch
and mm display
Zero an Axis in Zero Mode
Ensure DP500 is
in Zero Mode of Axis 1, 2 or 3
Zero an Axis in Set Mode
Ensure DP500 is
in Set Mode of Axis 1, 2 or 3
Ensure DP500 is
in Set Mode
Until display
shows
display
shows
Spherosyn LT
of axis 1
of axis 1, 2 or 3
See full manual on website for more details
user defined, use numeric keypad to enter value
(value is in whole minutes)
See full manual on website for more details to exit setup
of axis 1
cesky
DANSK deutsch espanol
francais italiano nederlan
pol
setup
T P E GENERIC nnILL LATHE
setup
ENCODER S26-LT nn26-LT
setup
RES 0.005 0.01 0.02 0.05
setup
DIR ---| |---
setup
MEASURE RAD DIA
setup
ERR COMP
setup
PLANE
(----)
(----)
(----)
(----)
(----)
(----)
setup
funcs ON OFF
setup
bEEP o n
setup
sleep
setup
COdE?
FUNCS
SETUP
-145.230
Note: values in mm
portugue russian
turkce
of axis 1, 2 or 3
of axis 1, 2 or 3
of axis 1, 2 or 3
of axis 1
ENTERING SETUP
set func
t o o l s
of axis 1
to scroll through functions, to return to setup menu
OFF
of axis 1
0
setup
reset
Sleep key
Axis 1
Axis 2
Axis 3
Power
LED
T00l 01
950.355
100.250
156.255