Nexcom VTC 210 Series User manual

NEXCOM International Co., Ltd.
NEXCOM International Co., Ltd.
Published June 2022 www.nexcom.com
Mobile Computing Solutions
Vehicle Telematics Computer
VTC 210 Series
User Manual

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ii
Contents
VTC 210 Series User Manual
Contents
Preface
Copyright .............................................................................................. iv
Disclaimer.............................................................................................. iv
Acknowledgements ............................................................................... iv
Regulatory Compliance Statements........................................................ iv
Declaration of Conformity...................................................................... iv
RoHS Compliance ................................................................................... v
Warranty and RMA ................................................................................ vi
Technical Support and Assistance........................................................... ix
Conventions Used in this Manual........................................................... ix
Global Service Contact Information......................................................... x
Package Contents..................................................................................xii
Ordering Information ............................................................................xiii
Chapter 1: Product Introduction
Overview ................................................................................................1
Key Features........................................................................................1
VTC 210 Physical Features.......................................................................2
Front View...........................................................................................2
Rear View............................................................................................2
VTC 210 Hardware Specifications............................................................3
Mechanical Dimensions: VTC 210 ...........................................................5
Knowing Your VTC210 ...........................................................................6
Front Panel ..........................................................................................6
Rear Panel ...........................................................................................7
Chapter 2: Jumpers and Switches
Before You Begin ....................................................................................8
Precautions .............................................................................................8
Jumper Settings ......................................................................................9
Locations of the Jumpers and Connectors.............................................10
Top View ...........................................................................................10
Bottom View .....................................................................................11
DIP Switch Settings............................................................................12
MCU Input Voltage ........................................................................12
Connector Pin Definitions .....................................................................13
External I/O Interfaces........................................................................13
LAN1 Port ......................................................................................13
LAN2 Port ......................................................................................13
M12 LAN Connector ........................................................................14
M12 LAN Connector ........................................................................14
HDMI1 Connector .............................................................................15
HDMI2 Connector (BOM option VGA) ...............................................15
VGA Connector (BOM option HDMI2) ...............................................16
Reset Button......................................................................................16
Power Button Connector...................................................................17
Channel Switch .................................................................................17
Flash Button ......................................................................................18
Connector location: SW5...................................................................18
SARADC Button ................................................................................18
Connector location: SW6...................................................................18
PMIC Reset Button ............................................................................19

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. iii
Contents
VTC 210 Series User Manual
Connector location: SW7...................................................................19
PMIC Power On Button .....................................................................19
Connector location: SW8...................................................................19
USB2.0 Connector .........................................................................20
Audio Connector ...........................................................................20
Internal Connectors...........................................................................21
DC IN Connector............................................................................21
DC OUT Connector........................................................................21
RTC Battery Connector...................................................................22
COM Connector ............................................................................22
USB OTG Wafer .............................................................................23
Micro SIM Slot ...............................................................................23
SD Card Slot ..................................................................................24
SOC Debug Port.............................................................................24
GPS Signal Connector ....................................................................25
WLAN Module ...............................................................................25
MCU DEBUG Port ..........................................................................26
MCU Download Port......................................................................26
M.2 3042 Key B Socket .................................................................27
Connector location: CN2................................................................27
Chapter 3: System Setup
Removing the Chassis Cover ................................................................28
Installing a WLAN Module.....................................................................29
Installing a WWAN Module (Mini-PCIe) .................................................30
Installing a SIM Card and MicroSD Card................................................31
Appendix A: GPS Feature
uBlox-NEO M8 Overview.......................................................................32
Technical Specifications.........................................................................32

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. iv
Preface
VTC 210 Series User Manual
Regulatory Compliance Statements
This section provides the FCC compliance statement for Class A devices and
describes how to keep the system CE compliant.
Declaration of Conformity
FCC
This equipment has been tested and verified to comply with the limits for
a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. Operation of this equipment in a residential area
(domestic environment) is likely to cause harmful interference, in which
case the user will be required to correct the interference (take adequate
measures) at their own expense.
CE
The product(s) described in this manual complies with all applicable
European Union (CE) directives if it has a CE marking. For computer systems
to remain CE compliant, only CE-compliant parts may be used. Maintaining
CE compliance also requires proper cable and cabling techniques.
Copyright
This publication, including all photographs, illustrations and software, is
protected under international copyright laws, with all rights reserved. No
part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written consent from
NEXCOM International Co., Ltd.
Disclaimer
The information in this document is subject to change without prior notice
and does not represent commitment from NEXCOM International Co., Ltd.
However, users may update their knowledge of any product in use by constantly
checking its manual posted on our website: http://www.nexcom.com. NEXCOM
shall not be liable for direct, indirect, special, incidental, or consequential
damages arising out of the use of any product, nor for any infringements
upon the rights of third parties, which may result from such use. Any implied
warranties of merchantability or fitness for any particular purpose is also
disclaimed.
Acknowledgements
VTC 210 is a trademark of NEXCOM International Co., Ltd. All other product
names mentioned herein are registered trademarks of their respective
owners.
PrefaCe

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. v
Preface
VTC 210 Series User Manual
RoHS Compliance
NEXCOM RoHS Environmental Policy and Status
Update
NEXCOM is a global citizen for building the digital
infrastructure. We are committed to providing green
products and services, which are compliant with
European Union RoHS (Restriction on Use of Hazardous Substance in
Electronic Equipment) directive 2011/65/EU, to be your trusted green
partner and to protect our environment.
RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg)
< 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent
Chromium (Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) <
0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or
1,000ppm.
In order to meet the RoHS compliant directives, NEXCOM has established an
engineering and manufacturing task force in to implement the introduction
of green products. The task force will ensure that we follow the standard
NEXCOM development procedure and that all the new RoHS components
and new manufacturing processes maintain the highest industry quality
levels for which NEXCOM are renowned.
How to recognize NEXCOM RoHS Products?
For existing products where there are non-RoHS and RoHS versions, the
suffix “(LF)” will be added to the compliant product name.
All new product models launched after January 2013 will be RoHS compliant.
They will use the usual NEXCOM naming convention.

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. vi
Preface
VTC 210 Series User Manual
Warranty and RMA
NEXCOM Warranty Period
NEXCOM manufactures products that are new or equivalent to new in
accordance with industry standard. NEXCOM warrants that products will be
free from defect in material and workmanship for 2 years, beginning on the
date of invoice by NEXCOM.
NEXCOM Return Merchandise Authorization (RMA)
▪Customers shall enclose the “NEXCOM RMA Service Form” with the
returned packages.
▪Customers must collect all the information about the problems
encountered and note anything abnormal or, print out any on-screen
messages, and describe the problems on the “NEXCOM RMA Service
Form” for the RMA number apply process.
▪Customers can send back the faulty products with or without accessories
(manuals, cable, etc.) and any components from the card, such as CPU
and RAM. If the components were suspected as part of the problems,
please note clearly which components are included. Otherwise, NEXCOM
is not responsible for the devices/parts.
▪Customers are responsible for the safe packaging of defective products,
making sure it is durable enough to be resistant against further damage
and deterioration during transportation. In case of damages occurred
during transportation, the repair is treated as “Out of Warranty.”
▪Any products returned by NEXCOM to other locations besides the
customers’ site will bear an extra charge and will be billed to the customer.
Repair Service Charges for Out-of-Warranty Products
NEXCOM will charge for out-of-warranty products in two categories, one is
basic diagnostic fee and another is component (product) fee.
System Level
▪Component fee: NEXCOM will only charge for main components such as
SMD chip, BGA chip, etc. Passive components will be repaired for free,
ex: resistor, capacitor.
▪Items will be replaced with NEXCOM products if the original one cannot
be repaired. Ex: motherboard, power supply, etc.
▪Replace with 3rd party products if needed.
▪If RMA goods can not be repaired, NEXCOM will return it to the customer
without any charge.
Board Level
▪Component fee: NEXCOM will only charge for main components, such
as SMD chip, BGA chip, etc. Passive components will be repaired for free,
ex: resistors, capacitors.
▪If RMA goods can not be repaired, NEXCOM will return it to the customer
without any charge.

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. vii
Preface
VTC 210 Series User Manual
Warnings
Read and adhere to all warnings, cautions, and notices in this guide and
the documentation supplied with the chassis, power supply, and accessory
modules. If the instructions for the chassis and power supply are inconsistent
with these instructions or the instructions for accessory modules, contact
the supplier to find out how you can ensure that your computer meets
safety and regulatory requirements.
Cautions
Electrostatic discharge (ESD) can damage system components. Do the
described procedures only at an ESD workstation. If no such station is
available, you can provide some ESD protection by wearing an antistatic
wrist strap and attaching it to a metal part of the computer chassis.
Safety Information
Before installing and using the device, note the following precautions:
▪Read all instructions carefully.
▪Do not place the unit on an unstable surface, cart, or stand.
▪Follow all warnings and cautions in this manual.
▪When replacing parts, ensure that your service technician uses parts
specified by the manufacturer.
▪Avoid using the system near water, in direct sunlight, or near a heating
device.
▪The load of the system unit does not solely rely for support from the
rackmounts located on the sides. Firm support from the bottom is highly
necessary in order to provide balance stability.
▪The computer is provided with a battery-powered real-time clock circuit.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.
Installation Recommendations
Ensure you have a stable, clean working environment. Dust and dirt can
get into components and cause a malfunction. Use containers to keep
small components separated.
Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow
require only a few simple tools, including the following:
• A Philips screwdriver
• A flat-tipped screwdriver
• A grounding strap
• An anti-static pad
Using your fingers can disconnect most of the connections. It is recom-
mended that you do not use needlenose pliers to disconnect connections
as these can damage the soft metal or plastic parts of the connectors.
Warning!
1. Handling the unit: carry the unit with both hands and handle it with care.
2. Maintenance: to keep the unit clean, use only approved cleaning products
or clean with a dry cloth.
3. CompactFlash: Turn off the unit’s power before inserting or removing a
CompactFlash storage card.
4. SIM: Do not insert or remove the SIM card when the system is powered
on. Always power off the system before inserting or removing the SIM
card.

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. viii
Preface
VTC 210 Series User Manual
Safety Precautions
▪Read these safety instructions carefully.
▪Keep this User Manual for later reference.
▪Disconnect this equipment from any AC outlet before cleaning. Use a
damp cloth. Do not use liquid or spray detergents for cleaning.
▪For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
▪Keep this equipment away from humidity.
▪Put this equipment on a stable surface during installation. Dropping it or
letting it fall may cause damage.
▪Do not leave this equipment in either an unconditioned environment or
in a above 40oC storage temperature as this may damage the equipment.
▪The openings on the enclosure are for air convection to protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
▪Make sure the voltage of the power source is correct before connecting
the equipment to the power outlet.
▪Place the power cord in a way so that people will not step on it. Do not
place anything on top of the power cord. Use a power cord that has been
approved for use with the product and that it matches the voltage and
current marked on the product’s electrical range label. The voltage and
current rating of the cord must be greater than the voltage and current
rating marked on the product.
▪All cautions and warnings on the equipment should be noted.
▪If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
▪Never pour any liquid into an opening. This may cause fire or electrical
shock.
▪Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
▪If one of the following situations arises, get the equipment checked by
service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work
according to the user’s manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
▪Do not place heavy objects on the equipment.
▪The unit uses a three-wire ground cable which is equipped with a third
pin to ground the unit and prevent electric shock. Do not defeat the
purpose of this pin. If your outlet does not support this kind of plug,
contact your electrician to replace your obsolete outlet.
▪CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ix
Preface
VTC 210 Series User Manual
Conventions Used in this Manual
Warning:
Information about certain situations, which if not observed,
can cause personal injury. This will prevent injury to yourself
when performing a task.
CAUTION!
CAUTION!CAUTION! Caution:
Information to avoid damaging components or losing data.
Note:
Provides additional information to complete a task easily.
Technical Support and Assistance
1. For the most updated information of NEXCOM products, visit NEXCOM’s
website at www.nexcom.com.
2. For technical issues that require contacting our technical support team or
sales representative, please have the following information ready before
calling:
– Product name and serial number
– Detailed information of the peripheral devices
– Detailed information of the installed software (operating system,
version, application software, etc.)
– A complete description of the problem
– The exact wordings of the error messages
Warning!
1. Handling the unit: carry the unit with both hands and handle it with care.
2. Maintenance: to keep the unit clean, use only approved cleaning products
or clean with a dry cloth.

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. x
Preface
VTC 210 Series User Manual
Global Service Contact Information
Headquarters
NEXCOM International Co., Ltd.
9F, No. 920, Zhongzheng Rd.,
Zhonghe District, New Taipei City, 23586,
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
www.nexcom.com
Asia
Taiwan
NexAIoT Headquarters
Industry 4.0 and Cloud Services
13F, No.922, Zhongzheng Rd.,
Zhonghe District, New Taipei City,
23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexaiot.com
NexAIoT Co., Ltd.
Taichung Office
16F, No.250, Sec. 2, Chongde Rd.,
Beitun District,
Taichung City, 406, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexaiot.com
NexCOBOT Taiwan Co., Ltd.
13F, No.916, Zhongzheng Rd.,
Zhonghe District,
New Taipei City, 23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcobot.com
GreenBase Technology Corp.
13F, No.922, Zhongzheng Rd.,
Zhonghe District,
New Taipei City, 23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.com.tw
DivioTec Inc.
19F-1A, No.97, Sec.4, ChongXin Rd.,
Sanchong District,
New Taipei City, 24161, Taiwan, R.O.C.
Tel: [phone]
Email: [email protected]
www.diviotec.com
AIoT Cloud Corp.
13F, No.922, Zhongzheng Rd.,
Zhonghe District,
New Taipei City, 23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.aiotcloud.dev
EMBUX TECHNOLOGY CO., LTD.
13F, No.916 Zhongzheng Rd.,
Zhonghe District,
New Taipei City, 23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.embux.com
TMR TECHNOLOGIES CO., LTD.
13F, No.916 Zhongzheng Rd.,
Zhonghe District,
New Taipei City, 23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.tmrtek.com

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. xi
Preface
VTC 210 Series User Manual
NEXGOL Chongqing
1st Building No.999,
Star Boulevard, Yongchuan Dist,
Chongqing City, 402160, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
Beijing NexGemo Technology Co.,Ltd.
Room 205, No.1, Fazhan Rd.,
Beijing International Information Industry Base,
Changping District,
Beijing, 102206, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexgemo.com
Japan
NEXCOM Japan
9F, Tamachi Hara Bldg.,
4-11-5, Shiba Minato-ku,
Tokyo, 108-0014, Japan
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom-jp.com
China
NEXSEC Incorporated
201, Floor 2, Unit 2, Building 15, Yard 3,
Gaolizhang Road, Haidian District,
Beijing, 100094, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexsec.cn
NEXCOM Shanghai
Room 406-407, Building C, No 154, Lane 953,
Jianchuan Road, Minhang District,
Shanghai, 201108, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
NEXCOM Surveillance Technology Corp.
Floor 8, Building B3, Xiufeng Industrial Zone,
GanKeng Community, Buji Street,
LongGang District,
ShenZhen, 518112, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
America
USA
NEXCOM USA
46665 Fremont Blvd.,
Fremont CA 94538, USA
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.com
Europe
United Kingdom
NEXCOM EUROPE
10 Vincent Avenue,
Crownhill Business Centre,
Milton Keynes, Buckinghamshire
MK8 0AB, United Kingdom
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.com

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. xii
Preface
VTC 210 Series User Manual
Package Contents
Before continuing, verify that the VTC 210 package that you received is complete. Your
VTC 210 package should have all the items listed in the following table.
Item Part Number Description Specification Qty
1 4NCPF00334X00 Terminal Blocks 3P DECA:MC421-35003Z-1 3.5mm Female 180D Assy Green 1
2 50311F0127X00 (H) Round Head Screw Long Fei:P3*6ISO+ Nylok P3x6 Black Nylok 2
3 5060700035X00 HDMI Wire Mount Kang Yang:SWCM-1VB 13.85x11x7.8mm Nylon 66 UL94V-0 Black 2
4603ANT0115X00 GPS/GLONASS Antenna Unictron:SM-76G SMA Male L=5000mm 1

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. xiii
Preface
VTC 210 Series User Manual
Ordering Information
The following provides ordering information for the VTC 210 series.
▪VTC 210 (P/N: 10V00021000X0)
Qual-core ARM®Cortex-A53 processor, 2GB DDR4, 16GB eMMC, U-blox
GPS module, HDMI output, 2 x LAN, 1 x USB, 1 x RS232, 9~36VDC input

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. 1
Chapter 1: Product Introduction
VTC 210 Series User Manual
ChaPter 1: ProduCt IntroduCtIon
Key Features
▪Built-in Rockchip RK3328 Qual-core ARM®Cortex-A53 processor
▪Built-in u-blox-M8N GPS
▪1 x DB9 for full RS232
▪1 x HDMI, (BOM option VGA + Audio)
▪WLAN module option (USB interface)
Overview
▪1 x M.2 B Key for WWAN with 1 x internal Micro SIM slot
▪SDK for power/reset/WDT/IGN/UVP threshold/GNSS on/off control
▪Wide operating temperature -20°C~70°C
▪Wide range DC input from 9V ~ 36V
▪Certified by CE/FCC/E13

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. 2
Chapter 1: Product Introduction
VTC 210 Series User Manual
VTC 210 Physical Features
Front View
LAN1 & LAN2
HDMI
9~36VDC COM
USB 2.0
Antenna
Hole
Power ButtonReset
LED
Indicators
Rear View
Antenna
Hole
Antenna
Holes
Antenna
Connector

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. 3
Chapter 1: Product Introduction
VTC 210 Series User Manual
VTC 210 Hardware Specifications
CPU
▪Rockchip RD3328 Qual-Core ARM®Cortex-A53 processor
Memory
▪DDR4 2GB on board (BOM option 4GB)
Storage
▪eMMC 16GB on board
▪1 x internal microSD slot
Expansion
▪1 x M.2 3042 Key B (USB 2.0, USB 3.0) for WWAN with 1 x internal Micro
SIM
▪1 x USB 2.0 wafer for WiFi module
GNSS and Onboard Sensor
▪1 x Default U-blox NEO-M8N GNSS module for GPS/Glonass/QZSS/
Galileo/Beidou
▪G Sensor and gyroscope
I/O Interface-Front
▪1 x Power button with LED
▪4 x LED for WWAN, WLAN, LAN1, LAN2
▪2 x RJ45 10/100/1000 fast Ethernet with LED
▪1 x USB 2.0 Type A
▪1 x Reset button
▪2 x Antenna holes for WLAN
▪1 x Phoenix connector for power (9~36VDC)/GND/ignition input
I/O Interface-Rear
▪1 x HDMI 2.0a for 4K@60Hz output (BOM option 2nd display, 1 x VGA
output + 1 x audio jack output (L/R))
▪3 x Antenna holes for WWAN and GNSS
Power Management & Software Support
▪System power On/Off by ignition signal
Operating System
▪Linux
Dimensions
▪130 x 100 x 31 (W x D x H) (mm)
Weight
▪0.5kg
Environment
▪Operating temperatures: -20°C~70°C
▪Storage temperatures: -40°C~85°C
▪Relative humidity: 90% (non-condensing)
Vibration & Shock
▪Vibration
- Operating: MIL-STD-810H, Method 514.8, Category 4, common
carrier US highway truck vibration exposure

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. 4
Chapter 1: Product Introduction
VTC 210 Series User Manual
- Storage: MIL-STD-810H, Method 514.8, Category 24, minimum
integrity test
▪Shock
- Operating: MIL-STD-810H, Method 516.8, Procedure I, functional
shock=40g
- Non-operating: MIL-STD-810H, Method 516.8, Procedure V, crash
hazard shock test=75g
Certifications
▪CE approval
▪FCC Class A
▪E13 mark

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. 5
Chapter 1: Product Introduction
VTC 210 Series User Manual
Mechanical Dimensions: VTC 210
154.0
142.0
4.5 TYP.2
7.5 TYP.2
7.0
130.0 100.0
86.0
31.0
4.5 TYP.2

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. 6
Chapter 1: Product Introduction
VTC 210 Series User Manual
Knowing Your VTC210
Front Panel
Reset Button
Press to restart the system.
Antenna Hole
Used to install external antennas.
Power Button
Press to power-on or power-off the system.
LED Indicators
Indicates the data activity and link status of WWAN/WLAN/LAN1/LAN2
ports.
LAN 1 to LAN 2 Ports
Used to connect network devices.
USB 2.0 Port
Used to connect USB 2.0 devices.
9~36V DC Input
Used to plug a DC power cord.
LAN1 & LAN2
9~36VDC
USB 2.0
Antenna
Hole
Power ButtonReset
LED
Indicators
Antenna
Hole

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. 7
Chapter 1: Product Introduction
VTC 210 Series User Manual
Rear Panel COM
DB9 port used to connect serial devices. (Full RS232 signal)
HDMI
Used to connect an HDMI interface monitor.
Antenna Holes
Used to install external antennas.
HDMI
COM Antenna
Holes
Antenna
Connector