Next 658961 User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instru
c
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
• Clean using a glass cleaner and soft cloth. Do not use cleaning products containing abrasives as these will
scratch the glass.
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original
packaging
IMPORTANT
• The maximum load this shelf/these shelves can hold is 5 kg.
• We would recommend that the following methods to be used to hang the cabinet. NB - Screws & Raw plugs
for the wall are not included.
• Do not rub or scrub the surface when cleaning.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer
finish.
• Wood from MDF with a painted finish.
• A minimum of 2 persons is required to assemble this product.
• Wall fixings are not included.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• For general cleaning, periodically dust with a soft cloth.
• Made in China.
CARE INSTRUCTIONS
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking,
discolouration or warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
PRODUCT INFORMATION
658961 SPARKLE TALL CABINET
Page 1 of 6

1. Insert 4 x cambolts (B) into side panel 2 (both
L&R) .
2. Attach shelf panel 7 to side panel 2 (both
L&R).
3. Insert 4 x camlocks (A) into shelf panel 7.
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver.
GLASS INFORMATION
•This item contains glass. Please handle with extreme care.
•BS 7449: 1991.
FITTINGS
STEP ONE
•Batch No.10/2013
PARTS
•This product contains 4mm glass that does not conform to BS 6206. If the glass is chipped or broken replace
with glass of the type described. Consult the manufacturer, retailer or agent with regard to obtaining a
manufacturing specification and shape for replacement glass quoting the model number and batch number or
date of manufacture.
B
B
B
B
A
A
A
A
(4) Adjustable Shelf x 2
Page 2 of 6

1. Insert 2 x wooden dowel (C) into side panel 2
(both L&R).
2. Attach top panel 1 to the assembled unit with
4 x screws (G) and tighten with a screwdriver.
1. Insert 2 x wooden dowel (C) into side panel 2
(both L&R).
2. Attach bottom panel 3 to the assembled unit
with 4 x screws (G) and tighten with a
screwdriver.
1. Attach back panel 6 to the body with 16 x
screws (E) and tighten with a screwdriver.
STEP TWO
STEP THREE
STEP FOUR
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
6
C
C
G
G
G
G
C
C
G
G
G
G
Page 3 of 6

1. Attach door panels 5 to the side panel 2-L with
6 x screws (D) and tighted with a screwdriver.
1. Insert 8 x shelf supports (F) into side panel 2
(both L&R), ensure that the four supports for
shelf are all at the same height. Note that the
shelf position is adjustable.
2. Insert the adjustable shelf 4 (x2) onto the shelf
supports (F).
STEP FIVE
STEP SIX
5
5
4
4
1
3
F
FFF
FF
FF
Page 4 of 6

1. Use pencil to mark through predrilled hole on
side panel.
1. Use power tool drill through the pencil mark.
STEP SEVEN
STEP EIGHT
Page 5 of 6