Next 893141 User manual

Tools Needed
Helpline
If you have any problems with this product or require any
replacement fittings please contact Customer Services Tel:
0844 844 8999
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be
faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• This item contains glass. Please handle with extreme care.
• BS 7449: 1991
• Batch no: 10/2013
• Consult with retailer with regard to obtaining a manufacturing specification and shape for replacement mirror quoting the
model number,batch number and date of manufacture.
• Do not rub or scrub the surface when cleaning.
• This item contains 5mm annealed mirror glass ,if the glass is chipped or broken replace with glass of the type described on
this label.
• For general cleaning, periodically dust with a soft cloth.
CARE INSTRUCTIONS
• Do not use furniture polish.
• Do not put hot dishes directly on the surfaces of the item.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or
damage.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Made from Partical board & MDF with a pvc foil finish.
PRODUCT INFORMATION
• A minimum of two persons is required to assemble this product.
• We recommend that the packaging is used to protect the surfaces during assembly.
• For safety reasons this item must be fixed to the wall.
• Made in China.
GLASS INFORMATION
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Gloss finishes are prone to light surface scratching and it is therefore very important that
you care for this item correctly.
893141 BLACK BEVEL TALL CABINET
893141 BLACK BEVEL TALL CABINET893141 BLACK BEVEL TALL CABINET
893141 BLACK BEVEL TALL CABINET
Page 1 of 6

1. Insert 6 x cambolts (A) into panels 1 & 2 and tighten with
a screwdriver.
STEP ONE
FITTINGS
Please note:Remove the protective film after assembly of this product, this will
prevent accidental scratches during assembly.
PARTS
1Χ1 2Χ13Χ1
7Χ24Χ25Χ2 6Χ1
AΧ6 BΧ6 CΧ12
7.5*35m/m 15*10m/m 6*30m/m
DΧ1
5g
EΧ6
25mm
FΧ8
5*16m/m H35A+H=0
GΧ2
4*14m/m
HΧ12 IΧ8
Template
JΧ1
Page 2 of 6

1. Glue(D) and insert 6 x wooden dowels (C) into panel 1
and attach panels 5(x2) & 6 to panel 1.
2. Insert 3 x camlocks (B) into panels 6 & 5(x2) and tighten
with a screwdriver.
Ensure the arrow indicator is pointing towards the panel
edge and ensure the assembly bolt locates properly into
the camlock before turning
1. Slide panels 4(x2) into the assembled unit as shown in
diagram.
1. Glue(D) and insert 6 x wooden dowels (C) into panels
5(x2) & 6 and attach panel 2 to panels 5(x2) & 6 .
2. Insert 3 x camlocks (B) into panels 6 & 5(x2) and tighten
with a screwdriver.
Ensure the arrow indicator is pointing towards the panel
edge and ensure the assembly bolt locates properly into
the camlock before turning
STEP THREE
STEP FOUR
STEP TWO
Groove
Page 3 of 6

1. Attach 2 x hinges (G) to panel 3 with 4 x screws (H) using
a screwdriver clockwise until tight.
NB: Put the styrofoam under panel 3 to protect the mirror
1. Attach panel 3 to panel 1 with 4 x screws (H) through
hinges (G ) to fit the adjustable holes first and using a
screwdriver to tighten.
NB: Put the styrofoam under panel 3 to protect the mirror
To align doors use the adjustment diagram
below.
LATERAL
VERTICAL
FRONT- TO-BACK
3. once doors are correctly adjusted then fasten with 4 x
screws (H) on the remaining holes in the hinge plates(G) .
4. Use 6 x stickers (E) to cover the camholes .
1. Insert 8 x plastic fasteners (I) into the back panel
grooves and tighten with screws provided.
STEP SEVEN
STEP FIVE
STEP SIX
Styrofoam beneath
the mirror
Styrofoam beneath
the mirror
Styrofoam beneath
the mirror
Page 4 of 6

1. Use the template (A) provided to mark on the
wall the position of the fixings.
NB: Place the template over the back of the
cabinet to ensure that the holes match the
position of the hooks before drilling into your
wall
2. Use a spirit level to check that the fixings are level.
3. Drill four holes and insert an appropriate wall plug into
each. Insert the screws/washers and tighten . leaving the
screw head exposed by about 1/4 inch(6mm).
Warning:
Always ensure intended wall area to be drilled is
free from hidden electrical wires,water and gas
pipes.
NB:Wall fixings are not included- Please source
suitable fixing for your wall type. If in doubt
please consult a qualified trades person.
1. Lift the cabinet into position ensuring that the fixing
clips attached to the cabinet are firmly hooked over the
screw heads. Check the cabinet periodically to see that no
fitting has loosened and needs attention.
style 1 : left open
style 2 : right open
STEP NINE
STEP EIGHT
the
mirr
o
r
Style 1
Style 2
Page 5 of 6

1. Insert 8 x fittings (F) into the required position .
3. Insert panels 7(x2) onto the fittings (F) .
Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
STEP TEN
Style 1
Style 2
Page 6 of 6