Next SOPHIE 874595 User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• For general cleaning, periodically dust with a soft cloth.
• Do not put hot dishes directly on the surfaces of the item.
• Made from MDF with a painted finish.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
CARE INSTRUCTIONS
• Do not rub or scrub the surface when cleaning.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
PRODUCT INFORMATION
• Not suitable for use in bathrooms.
• Made in China.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Wall fixings are not included.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
.
• We recommend the use of the wall attachment bracket/strap provided for safety reasons.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
874595 SOPHIE MULTI CHEST
Page1of6

1. Insert 2 x wooden dowels (J) into top panel (1).
2. Attach top front rail (8) to top panel (1) with 3 x
screws (E) and tighten with a screwdriver.
1. Insert 2 x wooden dowels (J) into bottom panel
(6).
2. Attach lower front rail (7) to bottom panel (6) with
3 x screws (E) and tighten with a screwdriver.
FITTINGS
PARTS
STEP TWO
STEP ONE
B x 12 F x 12
Page2of6

1. Insert 4 x wooden dowels (C) and 4 x cambolts
(A) into side panel (2-R).
2. Attach 3 x shelf rails (4) and 1 x back rail (5) to
side panels (2-R).
3. Insert 4 x camlocks (B) into 3 x shelf rails (4) and
1 x back rail (5). Ensure the arrow indicator is
pointing towards the panel edge before tightening
with a screwdriver.
1. Insert 4 x wooden dowels (C) and 4 x cambolts
(A) into side panel (2-L).
2. Attach side panel (2-L) to the assembled unit.
3. Insert 4 x camlocks (B) into 3 x shelf rails (4) and
1 x back rail (5). Ensure the arrow indicator is
pointing towards the panel edge before tightening
with a screwdriver.
1. Insert 4 x wooden dowels (C) into bottom panel
(6).
2. Attach bottom panel (6) to the assembled unit
with 4 x screws (K) and tighten with a screwdriver.
STEP FIVE
STEP THREE
STEP FOUR
Page3of6

1. Insert 4 x wooden dowels (C) and 4 x cambolts
(
A
)
into to
p
p
anel
(
1
)
.
2. Attach top panel (1) to the assembled unit.
3. Insert 4 x camlocks (B) into side panels (2-L & 2-
R). Ensure the arrow indicator is pointing towards
the panel edge before tightening with a screwdriver.
1. Attach 2 x back panels (3) to the assembled unit
with 16 x screws (D) and tighten with a screwdriver.
1. Attach drawer side panels (11-L & 11-R) to drawer
back panel (10) with 4 x screws (E) and tighten.
2. Insert drawer bottom panel (12) into the grooves
of drawer side panels (11-L & 11-R).
3. Attach drawer front panel (9) to the assembled
unit with 4 x screws (E) and tighten.
4. Attach 3 x handles (G) to drawer front panel (9)
with 3 x bolts (F) and tighten.
N.B.: 6 transparent color handles and 6 pink color
handles are supplied, please assembled as your
p
ersonal
p
reference.
5. Repeat step 1 to 4 for remaining 3 drawers.
STEP SIX
STEP SEVEN
STEP EIGHT
Page4of6

1. Insert drawers into the unit.
1. Use screw (N) and washer (M) to secure the nylon
strap (L) to the top panel.
2. Secure the other end of the strap (L) to the wall
with an appropriate screw and wall plug for your
wall type. To hide the strap behind the unit, drill the
holes lower than the top of unit.
Warning: Always ensure the area to be drilled is
free from hidden electrical wires, water and gas
pipes.
NB: Wall fixings are not included, please source
suitable fixings for your wall type. If in doubt please
consult a qualified trades person.
STEP TEN
STEP NINE
Page5of6

Next Retail Ltd, Desford Road, Leicester, LE19 4AT
PACKAGING LAYOUT
Page6of6