Next ASHTON 853857 User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
• Do not put hot dishes directly on the surfaces of the item.
• For general cleaning, periodically dust with a soft cloth.
• Made from MDF with a painted finish.
• Made in China.
• Do not rub or scrub the surface when cleaning.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Wall fixings are not included.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
.
• Carefully check that you have all parts before beginning assembly.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
• We recommend the use of the wall attachment bracket/strap provided for safety reasons.
• Not suitable for use in bathrooms.
CARE INSTRUCTIONS
PRODUCT INFORMATION
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
853857 ASHTON 4 DRAWER CHEST
Page1of5

1. Insert 3 x cambolts (A) and 3 x wooden
dowels (C) into side panel 2-R.
2. Attach 3 x shelf panels 6 to side panel 2-R.
3. Insert 3 x camlocks (B) into shelf panels 6.
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver.
1. Insert 1 x cambolt (A) and 1 x wooden dowel
(C) into side panel 2-R.
2. Attach 1 x back rail 5 to side panel 2-R.
3. Insert 1 x camlock (B) into back panel 5.
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver.
STEP ONE
FITTINGS
PARTS
STEP TWO
(1) Top Panel
x 1
Page2of5

1. Insert 4 x cambolts (A) and 4 x wooden
dowels (C) into side panel 2-L.
2. Attach side panel 2-L to the assembled unit.
3. Insert 4 x camlocks (B) into 1 x back rail 5 and
3 x shelf panel 6. Ensure the arrow indicator is
pointing towards the panel edge before
tightening with a screwdriver.
1. Insert 4 x wooden dowels (C) into bottom
panel 3.
2. Attach bottom panel 3 to the assembled unit
with 4 x screws (D) and tighten.
1. Insert 4 x cambolts (A) and 4 x wooden
dowels (C) into top panel 1.
2. Attach top panel 1 to the assembled unit.
3. Insert 4 x camlocks (B) into side panel 2 (both
L&R). Ensure the arrow indicator is pointing
towards the panel edge before tightening with a
screwdriver.
STEP THREE
STEP FOUR
STEP FIVE
Page3of5

1. Attach back panel 4 to the assembled unit
with 12 x screws (E) and tighten with a
screwdriver.
1. Attach drawer side panel 9 (both L&R) to
drawer back panel 8 with 4 x screws (G) and
tighten.
2. Insert drawer bottom panel 10 into grooves of
drawer side panel 9 (both L&R).
3. Attach drawer front panel 7 to the assembled
unit with 4 x screws (G) and tighten.
4. Attach 1 x handle (H) to drawer front panel 7
with 2 x bolts (F) and tighten.
Repeat step 1 to 4 for remaining 3 drawers.
1. Attach 4 x stopper (K) to 3 x shelf panels 6
and 1 x bottom panel 3 with 4 x screws (J) and
tighten.
STEP SEVEN
STEP EIGHT
STEP SIX
Page4of5

1. Insert the drawers into the unit.
2. Insert 4 x paper cards (L) to 4 x handles (H).
1. Use screw (C) and washer (B) to secure the
nylon strap (A) to the top panel.
2. Secure the other end of the strap to the wall
with an appropriate screw and wall plug for your
wall type. To hide the strap behind the unit, drill
the holes lower than the top of unit.
Warning : Always ensure the area to be drilled is
free from hidden electrical wires, water and gas
pipes.
NB: Wall fixings are not included-please source
suitable fixings for your wall type. If in doubt
please consult a qualified trades person.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP NINE
STEP TEN
Page5of5