Next ASHTON 858081 User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer
finish.
• Do not put hot dishes directly on the surfaces of the item.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not rub or scrub the surface when cleaning.
• For general cleaning, periodically dust with a soft cloth.
CARE INSTRUCTIONS
• A minimum of 2 persons is required to assemble this product.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
PRODUCT INFORMATION
• Not suitable for use in bathrooms.
• Made in China.
• Made from MDF with painted finish.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We recommend that the packaging is used to protect the surfaces during assembly.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
858081 ASHTON HALL CABINET
Page1of7

1. Attach stopper (F) to shelf rail 5 with 2 x screws
(G) and tighten.
1. Insert 2 x cambolts (A) and 2 x wooden dowels
(L) into the divider panel 4.
2. Attach the shelf rail 5&6 to the divider panel 4.
3. Insert 2 x camlocks (B) into the shelf rail 5&6.
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver.
FITTINGS
PARTS
STEP TWO
STEP ONE
GG
5
F
B
A
L
B
L
5
4
6
(1) Top Panel x 1 (2) Side Panel (L&R) x 2 (5) Shelf Rail x 1
(4) Divider Panel x 1
(11) Drawer Front
Panel x 1
(6) Shelf Rail x 1
Page2of7

1. Insert 1 x cambolt (A) and 1 x wooden dowel (L)
into the side
p
anel 2-L.
2. Attach the lower rail 7 to the side panel 2-L.
3. Insert 1 x camlock (B) into the back rail 7.
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver.
1. Insert 1 x cambolt (A) and 1 x wooden dowel (L)
into the side panel 2-L.
2. Attach the shelf rail 6 to the side panel 2-L.
3. Insert 1 x camlock (B) into the shelf rail 6.
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver.
1. Insert 2 x cambolts (A) and 2 x wooden dowels
(L) into the side panel 2-R.
2. Attach side panel 2-R to the assembled unit.
3. Insert 2 x camlocks (B) into the shelf rail 5 and
back rail 7. Ensure the arrow indicator is pointing
towards the panel edge before tightening with a
screwdriver.
1. Insert 6 x wooden dowels (L) to the bottom
panel 3.
2. Attach bottom panel 3 to the assembled unit
with 6 x screws (H) and tighten with a
screwdriver.
STEP THREE
STEP FOUR
STEP FIVE
STEP SIX
BL
2-L
7
B
L
2-L
7
5
6
4
B
B
L
L
2-R
2-L
4
7
5
L
L
L
L
L
L
H
H
H
H
H
H
3
2-R
Page3of7

1. Insert 6 x cambolts (A) and 6 x wooden dowels
(L) into top panel 1.
2. Attach top panel 1 to the assembled unit.
3. Insert 6 x camlocks (B) into the divider panel 4
and the side panel 2 (both L&R). Ensure the
arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
1. Attach back panel 8, back panel 9 to the
assembled unit with 20 x screws (K) and tighten
wi
t
h
a
sc
r
e
w
d
riv
e
r.
1. Attach 6 x handles (M) to door panel 10 with 12
x bolts
(
N
)
and ti
g
hten with a screwdriver.
STEP NINE
STEP EIGHT
STEP SEVEN
BB
B
B
B
B
LL
LL
LL
1
2-L
2-R
4
8
9
K
K
KK
K
KK
K
K
K
K
K
K
K
K
K
K
K
K
K
Page4of7

1. Attach 2 x hinges (D) to door panel 10 with 4 x
screws
(
E
),
ti
g
hten with a screwdriver.
2. Attach 1 x rubber
p
ad
(
Q
)
to door
p
anel 10.
1. Attach door panels 10 to the side panels 2-R
with 4 x screws (E) and tighten with a
screwdriver.
2. Insert 8 x shelf supporters (P) to the assembled
unit. Ensure all supports are at the same level for
each shelf.
3. Place adjustable shelf panel 20 (x2) onto the
shelf supports (P).
Note: The gaps between the doors and frame can
be changed by making adjustments to hinges with
a screwdriver. Refer to adjustment diagrams.
Laterally (Side to Side)
Front to bac
k
V
erticall
y
(
u
p
and down
)
1. Insert 4 x cambolts (A) into the drawer front
panel 11.
2. Attach drawer front panel 11 to the side panel
14 (both L&R).
3. Insert 4 x camlocks (C) to the drawer side panel
14 (both L&R). Ensure the arrow indicator is
pointing towards the panel edge before tightening
with a screwdriver.
4. Insert the drawer bottom panel 15 into grooves
of drawer side panel 14 (both L&R).
5. Attach drawer back panel 13 to the assembled
unit with 4 x screws (J) and tighten.
6. Attach 2 x handle (M) to drawer front panel 11
with 4 x bolts (N) and tighten.
STEP ELEVEN
STEP TWELVE
STEP TEN
E
E
E
EEE
D
D
D
10
Q
C
C
C
CA
A
A
A
J
J
J
J
14-R
14-L 11
15
13
N
NM
M
10
20(x2)
2-R
2-L 4
Page5of7

1. Insert 4 x cambolts (A) into the drawer front
panel 12.
2. Attach drawer front panel 12 to the side panel
14 (both L&R).
3. Insert 4 x camlocks (C) to the drawer side panel
14 (both L&R). Ensure the arrow indicator is
pointing towards the panel edge before tightening
with a screwdriver.
4. Insert the drawer bottom panel 15 into grooves
of drawer side panel 14 (both L&R).
5. Attach drawer back panel 13 to the assembled
unit with 4 x screws (J) and tighten.
6. Attach 2 x handle (M) to drawer front panel 12
with 4 x bolts (N) and tighten.
1. Insert 4 x cambolts (A) into the drawer front
panel 16.
2. Attach drawer front panel 16 to the side panel
18 (both L&R).
3. Insert 4 x camlocks (C) into the drawer side
panel 18 (both L&R). Ensure the arrow indicator is
pointing towards the panel edge before tightening
with a screwdriver.
4. Insert the drawer bottom panel 19 into grooves
of drawer side panel 18 (both L&R).
5. Attach drawer back panel 17 to the assembled
unit with 4 x screws (J) and tighten.
6. Attach 2 x handle (M) to the drawer front panel
16 with 4 x bolts (N) and tighten.
STEP THIRTEEN
STEP FOURTEEN
C
C
J
J
J
J
12
14-R
15
13
M
M
N
N
A
A
CC
C
C
J
J
J
J
18-L
18-R 16
19
17
Page6of7

1. Insert 12 x paper card (R) into 12 x handles (M).
1. Use screw (C) and washer (B) to secure the
nylon strap (A) to the back of the top panel.
2. Secure the other end of the strap to the wall
with an appropriate screw, washer and wall plug
f
o
r
you
r w
a
ll
type
.
WARNING : Always ensure the area to be drilled
is free from hidden electrical wires, water and gas
p
i
pes
.
NOTE : Wall fixings are not included. Please
source suitable fixings for your wall type, if in
doubt
p
l
ease
co
n
su
l
t
a
qua
lifi
ed
t
r
ades
pe
r
so
n.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP SIXTEEN
STEP FIFTEEN
R
R
R
R
R
R
R
R
R
11
12
16
Page7of7