Next ISABELLA 855836 User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Made from MDF with painted finish.
• Do not put hot dishes directly on the surfaces of the item.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
• Carefully check that you have all parts before beginning assembly.
• A minimum of 2 persons is required to assemble this product.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
PRODUCT INFORMATION
• Made in China.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not rub or scrub the surface when cleaning.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We recommend that the packaging is used to protect the surfaces during assembly.
• For general cleaning, periodically dust with a soft cloth.
CARE INSTRUCTIONS
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• Keep fittings out of children's reach and keep children well away from the construction area.
855836 ISABELLA SINK CONSOLE
Page 1 of 6

1. Attach 2 x front foot 9 to bottom panel 3 with 4 x
bolts (M), 4 x washers (P), and 4 x spring washers
(N) and tighten.
1. Attach 2 x back foot 4 (both L&R) to bottom
panel 3 with 6 x bolts (L) and tighten.
STEP TWO
STEP ONE
FITTINGS
PARTS
3
4-R
4-L
LL
L
LL
L
G x 2
J x 4 N x 4
P x 4
M x 4
(1) Top Panel x 1 (3) Bottom Panel x 1(2) Side Panel (L&R) x 2 (5) Shelf Panel x 1
(4) Back Foot (L&R) x 2
P
P
3M
Page 2 of 6

1. Insert 4 x cambolts (B) and 1 x wooden dowel
(C) into side panel 2-R.
2. Attach back rail 8,front top rail 7 and top back
rail 10 to side panel 2-R.
3. Insert 4 x camlocks (A) into back rail 8, front top
rail 7 and top back rail 10. Ensure the arrow
indicator is pointing towards the panel edge
before tightening with a screwdriver.
1. Insert 4 x cambolts (B) and 1 x wooden dowel
(C) into side panel 2-L.
2. Attach side panel 2-L to the assembled unit.
3. Insert 4 x camlocks (A) into back rail 8, front top
rail 7 and top back rail 10. Ensure the arrow
indicator is pointing towards the panel edge
before tightening with a screwdriver.
1. Insert 4 x cambolts (B) and 4 x wooden dowels
(C) into bottom panel 3.
2. Attach bottom panel 3 to the assembled unit.
3. Insert 4 x camlocks (A) into side panel 2 (both
L&R). Ensure the arrow indicator is pointing
towards the panel edge before tightening with a
screwdriver.
STEP THREE
STEP FOUR
STEP FIVE
10
A
A
A
B
B
B
2-R
C
8
A
B
7
10
2-R
2-L
A
A
A
B
B
B
B
C
A
8
7
2-L
3
2-R
C
C
C
C
BB
BB
A
AA
A
Page 3 of 6

1. Attach top panel 1 to the assembled unit with 4
x bolts (J) and tighten.
2. Insert the back panel 11 into grooves of bottom
panel 3.
1. Attach back panel 11 to middle back rail 8 with 3
x screws (F), tighten with a screwdriver.
STEP EIGHT
STEP SEVEN
STEP SIX
2-R
1
2-L
J
J
J
J
3
11
8
Page 4 of 6

1. Attach 4 x hinges (D) to door panels 6 (both
L&R) with 8 x screws (E).
2. Attach 2 x handle (G) to door panel 6 (both L&R)
with 2 x screw (H), tighten with a screwdriver.
1. Attach door panel 6 (both L&R) to the body of
unit with 16 x screws (E), tighten with a
screwdriver.
Note: The gaps between the door and frame can
be changed by making adjustments to the hinges
with a screwdriver. Refer to adjustment diagrams.
Laterally (Side to Side)
Front to back
Vertically ( up and down)
1. Insert 4 x shelf supports (K) into side panel 2
(both L&R), ensure that the four supports for shelf
are all at the same height. Note that the shelf
position is adjustable.
3. Insert the adjustable shelf 5 onto the shelf
supports (K).
STEP TEN
STEP NINE
STEP ELEVEN
E
E
EE
6-L
E
E
EE
6-R
6-L
6-R
5
Page 5 of 6

1. Use pencil to mark through predrilled hole on
side panel.
1. Use power tool drill through the pencil mark.
1. Attach the assembled unit to the wall with 4 x
screws, tighted with a screwdriver.
Warning: Always ensure the area to be drilled is
free from hidden electrical wires, water and gas
pipes.
NB: Wall fixings are not incuded, please source
suitable fixings for your wall type. If in doubt
please consult a qualified trades person.
STEP FOURTEEN
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP THIRTEEN
STEP TWELVE
Wall
5
6-L
6-R
6-L
6-R
Page 6 of 6