Next CORSICA S User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
ASSEMBLY INSTRUCTIONS
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
CORSICA S DESK
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching
or damage.
• Made from MDF,hollow board & Honeycomb board with a wood effect finish.
• Made in China.
CARE INSTRUCTIONS
• A minimum of two persons is required to assemble this product.
• Do not use furniture polish.
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
• Keep fittings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Do not put hot dishes directly on the surfaces of the item.
• Do not rub or scrub the surface when cleaning.
PRODUCT INFORMATION
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• For general cleaning, periodically dust with a soft cloth.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
Page 1 of 6

PARTS
FITTINGS
1.Insert 8 x cambolts (E) into panels 4, 5 & 6
and tighten with a screwdriver.
2.Insert 2 x bolts (L) into nuts fixed on panel 2
and turn bolts (L) clockwise until tight by hand.
STEP ONE
Page 2 of 6

1.Attach panel 5 to panel 8 with 2 x screws (H)
using an Allen key (I) to tighten.
1. Glue and insert 1 x wooden dowel (A) into
panel 5.
2. Attach panel 9 to panel 5 .
3. Insert 2 x camlocks (D) into panel 9.
Ensure the arrow indicators are pointing towards
the panel edges before tightening with a
screwdriver.
4.Attach panel 2 to panel 9 with 2 x screws (H)
using an Allen key (I) to tighten.
STEP THREE
STEP TWO
1. Glue and insert 1 x wooden dowel (A) into
panel 2 .
2. Attach panel 10 to panel 2 .
3. Insert 2 x camlocks (D) into panel 10.
Ensure the arrow indicators are pointing towards
the panel edges before tightening with a
screwdriver.
4.Attach panel 6 to panel 10 with 2 x screws (H)
using an Allen key (I) to tighten.
STEP FOUR
Page 3 of 6

1. Glue and insert 1 x wooden dowel (A) into
panel 6 .
2. Attach panel 11 to panel 6 .
3. Insert 2 x camlocks (D) into panel 11.
Ensure the arrow indicators are pointing towards
the panel edges before tightening with a
screwdriver.
4.Attach panel 7 to panel 11 with 2 x screws (H)
using an Allen key (I) to tighten.
1.Attach panel 1 to panels 7, 6 , 2 & 5 with
8 x screws (H) using an Allen key (I) to tighten.
Please note: The panel 1 have two different
colour foil ,when you assemble ,please chose the
prefer colour you like on the outside.
STEP SIX
STEP FIVE
1. Glue and insert 2 x wooden dowels (B) into
panel 2.
2. Attach panel 3 to panel 2 .
3.Cover 2 x metal pieces (M) onto 2 x bolts (L)
and then screw 2 x metal nuts (K) with
spanner (N) until tight.
STEP SEVEN
Page 4 of 6

1. Lift the unit upright carefully.
2. Glue and insert 1 x wooden dowel (A) into
panel 8 .
2. Attach panel 4 to panels 1 & 8 with 2 x screws (H)
using an Allen key (I) to tighten.
4. Insert 2 x camlocks (D) into panel 8 .
Ensure the arrow indicators are pointing towards
the panel edges before tightening with a
screwdriver.
1.Use 8 x stickers (F) to cover the holes on
panels 7, 9 , 10 & 11.
2.Use 2 x stickers (G) to cover the holes on panel 3.
STEP EIGHT
STEP NINE
1.Please consider the height of metal bracket (O)
from the groove 1596 mm to determine the height of
hole on the wall .
2. Drill one hole and insert wall plugs ,then put
the screw through the 1× metal bracket (O)
into the wall
Warning:
Always ensure intended wall area to be drilled is
free from hidden electrical wires, water and gas
pipes.
Warning:
Wall fixings are not included- please source
suitable fixings for your wall type. If in doubt,
please consult a qualified trades person.
STEP TEN
please consult a qualified trades person.
Page 5 of 6

1.Move the unit to slot the bracket (O)
through the backboard of the product.
1.Ensure the brackets (O) to fit in the groove
under the top panel 4 .
2.Move the unit on the appropriate position, and then
fix the bracket (O) with 1 × screw (J) with
a screwdriver to tighten.
3.This product must be fitted to the wall to prevent
damage to the product during use. Periodically check
STEP TWELVE
STEP ELEVEN
damage to the product during use. Periodically check
that no fittings have loosened.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 6 of 6