Next LITTLE HADBURY 882985 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• Wall fixings are not included.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Please do not apply adhesive substrates for example , sticky tape to the product.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not put hot dishes directly on the surfaces of the item.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• Do not use furniture polish.
• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
• A minimum of two persons is required to assemble this product.
• Made from hollow board,particle board & MDF with a wood effect finish.
CARE INSTRUCTIONS
PRODUCT INFORMATION
• We recommend the use of the wall attachment bracket/strap provided for safety reasons.
• Made in China.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
882985 LITTLE HADBURY DOUBLE ROBE
882985 LITTLE HADBURY DOUBLE ROBE882985 LITTLE HADBURY DOUBLE ROBE
882985 LITTLE HADBURY DOUBLE ROBE
Page 1 of 6

1. Attach panels 12, 13 & 15 to panel 14 with 6 x
screws (F) and tighten with a screwdriver.
STEP ONE
FITTINGS
PARTS
5g 15*10mm 7.5*24.5mm 4*38mm 30.5*34*14mm 4*16mm 25mm 3*12mm
KX2
OX2
1.5*13*40*40mm
DX19CX5BX2AX14 EX19 FX6 GX2 HX6 IX6
8*30mm 6*30mm
JX1
MX6LX20 NX24
F
Page 2 of 6

1. Insert 3 x cambolts (E) into panel 11 and tighten
with a screwdriver.
2. Slide panel 16 into the assembled drawer frame.
1. Glue and insert 5 x wooden dowels (C) into
panels 12, 13 & 15.
2. Attach panel 11 to panels 12, 13 & 15.
3. Insert 3 x camlocks (D ) into panels 12, 13 & 15 and
tighten with a screwdriver.
Ensuring the arrow indicator is pointing toward the
panel edge before tightening with a screwdriver.
1. Insert 16 x cambolts (E) into panels 2 & 3 and
tighten with a screwdriver.
2. Secure 2 x hanging rail holders (G) to panels 2 & 3
with 6 x screws (H) as shown.
3. Secure 1 x stopper (J) to panel 1 with 2 x screws
provided.
Note:The stopper must be facing towards the outside
of panel 1.
4. Attach 2 x brackets (K) to panel 1 with 2 x screws
(O).
STEP FOUR
STEP TWO
STEP THREE
G
H
1
J
G
H
2
3
11
E
C
B
Page 3 of 6

1. Glue and insert 7 x wooden dowels (A) into
panels 4, 5, 6, 7 & 1.
2. Attach panels 4, 5, 6, 7 & 1 to panel 2.
3. Insert 8 x camlocks (D ) into panels 4, 5, 6, 7 & 1
and tighten with a screwdriver.
Ensuring the arrow indicator is pointing toward the
panel edge before tightening with a screwdriver.
1. Silde panels 9 (x2) into the grooves of the
assembled unit.
1. Glue and insert 7 x wooden dowels (A) into panels
4, 5, 6, 7 & 1.
2. Attach panel 3 to panels 4, 5, 6, 7 & 1.
3. Insert 8 x camlocks (D ) into panels 4, 5, 6, 7 & 1
and tighten with a screwdriver.
Ensuring the arrow indicator is pointing toward the
panel edge before tightening with a screwdriver.
STEP FIVE
STEP SEVEN
STEP SIX
2
1
4
5
6
7
B
A
9
9
1
5
6
Page 4 of 6

1. Carefully lift the unit upright. The unit should be
lifted by two people.
2. Secure hanging rail 8 onto the hanging rail holder
(G) as shown.
3. Use 6 x stickers (I) to cover the holes on panel 1.
1. Attach 6 × hinges (M) to panel 10(X2) with 12 ×
screws (N) using a screwdriver clockwise until tight.
X 2 UNITS
1. Attach panels 10 (x2) to the unit with 12 × screws
(N) through hinges ( M) using a screwdriver to
tighten.
To align doors use the adjustment
diagram below.
LATERAL
VERTICAL
FRONT- TO-BACK
STEP NINE
STEP EIGHT
STEP TEN
M
N
G
Page 5 of 6

1. Insert the drawer into the assembled unit as
shown in diagram.
1. Insert 20 × plastic fasteners (L) into the back panel
grooves and tighten with screws provided.
2. Move the unit into desired position.
3. Secure the 2 × "L" metal brackets (K) to the wall
with an appropriate screw and wall plug for your wall
type (not provided).
Warning:
please note this item need to be fixed on the
wall to prevent falling forward when product
is in use.
Warning:
Always ensure intended wall area to be
drilled is free from hidden electrical
wires,water and gas pipes.
NB:Wall fixings are not included-Please
source suitable fixing for your wall type. If in
doubt please consult a qualified trades
person.
STEP ELEVEN
STEP TWELVE
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
1
L
L
Page 6 of 6