Next CORSICA 653993 User manual

Tools Needed
Helpline
If you have any problems with this product or require any
replacement fittings please contact Customer Services Tel:
0333 777 8999
by-step instructions.
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be
faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Keep fittings out of children's reach and keep children well away from the construction area.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-
• Carefully check that you have all parts before beginning assembly.
653993 CORSICA TV UNIT
• Wall fixings are not included.
• For general cleaning, periodically dust with a soft cloth.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Do not rub or scrub the surface when cleaning.
• Keep fittings out of children's reach and keep children well away from the construction area.
• A minimum of two persons is required to assemble this product.
CARE INSTRUCTIONS
PRODUCT INFORMATION
• Made from hollow board & Honeycomb board ,partical board with a wood effect finish.
• Made in China
• We recommend that the packaging is used to protect the surfaces during assembly.
• Do not use furniture polish.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or
damage.
• Do not put hot dishes directly on the surfaces of the item.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
Page 1 of 3

1. Insert 10 x cambolts (C) into panels 1, 2 & 3(X2) using a
PARTS
FITTINGS
STEP ONE
1. Insert 10 x cambolts (C) into panels 1, 2 & 3(X2) using a
screwdriver until tight.
1. Glue and insert 2 x wooden dowels(A) into panel 1.
2. Attach panel 1 to panels 3x(2)
3. Insert 4 x camlocks (D) into panel 1 and tighten with a
screwdriver.
Ensuring the arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
STEP TWO
Page 2 of 3

1. Glue and insert 2 x wooden dowels(A) into panel 1.
2. Attach panel 5 to panel 1.
3. Insert 1 x camlock (D) into panel 5 and tighten with a
screwdriver.
Ensuring the arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
1. Glue and insert 2 x wooden dowels(A) into panel 2.
2. Attach panel 2 to panels 3x(2)
3. Insert 4 x camlocks (D) into panel 2 and tighten with a
screwdriver.
4. Glue and insert 2 x wooden dowels(A) into panel 2.
5. Attach panel 6 to panel 2.
6. Insert 1 x camlock (D) into panel 6 and tighten with a
screwdriver.
Ensuring the arrow indicator is pointing towards the panel
STEP THREE
STEP FOUR
edge before tightening with a screwdriver.
1. Attach panels 4 (x2) to panels 1 & 2 with 8 x screws (E)
and tighten with an Allen key (F) .
2. Carefully upright the assembly unit .
Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
STEP FIVE
Page 3 of 3