Next OPUS User manual

Tools Needed
Helpline
If you have any problems with this product or require any replacement
fittings please contact Customer Services Tel:[phone]
by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be faulty. Should you need to return
the unassembled product, please repack in the original packaging.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of two persons is required to assemble this product.
OPUS GLOSS STORAGE COFFEE TABLE
• Made from hollow board, honeycomb board ,partical board & MDF with PVC foil finish
PRODUCT INFORMATION
• For general cleaning, periodically dust with a soft cloth.
• Do not use furniture polish.
CARE INSTRUCTIONS
• Made in China
•Gloss finishes are prone to light surface scratch and it is therefore very imporant that you care for this item correctly.
•For general cleaning, periodically dust with a soft clean lint-free cloth or a soft micro fibre cloth Please note soft cloths (including yellow dusters) contain
abrasive fibres which can lightly scratch the surface, if in doubt please try your cloth in an inconspicuous area of the furniture first to assess its suitability.
• Do not rub or scrub the surface when cleaning.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or damage.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Do not put hot dishes directly on the surfaces of the item.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or warping.
Page 1 of 3

Please remove the protective clear film on the gloss panels when required in the
steps (5) & (6) as this will prevent any accidental scratches which may occur during assembly.
1. Insert 10× cambolts (D) into panels (1) & (3)
by a screwdriver until tight.
STEP ONE
FITTINGS
PARTS
D
D
1. Insert and glue 2×wooden dowels (A) into
panel (3) and attach panel (2) to panel (3).
2. Insert 3×camlocks ( C ) into panel (2).
Ensuring the arrow indicator is pointing
towards the panel edge and turn camlocks
clockwise until tight by a screwdriver.
STEP TWO
3
1
D
D
D
2
3
B
C
Page 2 of 3

1. Insert and glue 2× wooden dowels (A) into
panel (2) and attach panel (3) to panel (2).
2. Insert 3×camlocks ( C ) into panel (2).
Ensuring the arrow indicator is pointing
towards the panel edge and turn camlocks
clockwise until tight by a screwdriver.
1.Insert and glue 4×wooden dowels (A) into
panels (2)& (3) , and attach panel (1) to
panels (2) & (3).
2. Insert 7×camlocks ( C ) into panels (2) & (3) .
Ensuring the arrow indicator is pointing
towards the panel edge and turn camlocks
clockwise until tight by a screwdriver.
1.Insert and glue 4×wooden dowels (A) into
panels (2)& (3) , and attach panel (1) to
STEP THREE
STEP FOUR
STEP FIVE
3
2
C
B
2
1
A
panels (2)& (3) , and attach panel (1) to
panels (2) & (3).
2. Insert 7×camlocks ( C ) into panels (2) & (3) .
Ensuring the arrow indicator is pointing
towards the panel edge and turn camlocks
clockwise until tight by a screwdriver.
Please note remove the protective film from
panels (1) & (3).
1,Use the 8× stickers (E) to cover the camlock
holes.
2,Insert the panels (4) & (5) to the assembled
unit.
Please note two people are required to insert
each panel at one time.
Should you need to disassemble the product ,
to remove the top panels (4) & (5) please flick
the catches up on the runner as shown in
diagram .Please note two people are required
to remove the panels one at a time
3, Remove the protective film from panels
(4) & (5).
Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
STEP SIX
Page 3 of 3