Next SOPHIE CABIN STATION 889951 User manual

.
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• Made in China.
• A mark is present on the bed to show the maximum height of the mattress to be used.
• Do not use this item if any structural part is broken or missing.
• WARNING: Do not use this child's bed if any part is broken, torn or missing.
• High beds and the upper bed of bunk beds are not suitable for children under six years due to risk of injury from falls.
• WARNING: Children can become trapped between the bed and the wall. To avoid risk of serious injury the distance
between the top safety barrier and the wall shall not exceed 75mm or shall be more than 230mm.
• WARNING: Do not place this child's bed near heat sources, windows and other furniture.
• Ensure not to leave items such as ropes, strings, cords, harnesses and belts attached to or hung to the bunk/high bed
due to the risk of strangulation.
• Made from MDF with a painted finish.
• This child's bed is recommended for use by children aged 6 and upwards.
• The cot shall no longer be used once the child is able to climb out in order to prevent injury from falling.
• BS EN 747-1:2007
PRODUCT INFORMATION
• A mattress measuring 90cm x 190cm is intended for use with this child's bed.
• All assembly fittings shall always be tightened properly. Screws shall not be loose because a child can squeeze parts
of the body, or clothing (e.g. strings, necklaces, ribbons for babies, dummies, etc.) could get caught. There would be
danger of strangulation.
• Children are likely to play, bounce, jump and climb on beds, therefore the child's bed should not be placed too close
to other furniture or windows, and should be placed either tight to any wall or have a gap of 300mm between the wall
and the side of the bed.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We recommend that the packaging is used to protect the surfaces during assembly.
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• A minimum of 2 persons is required to assemble this product.
889951 SOPHIE CABIN STATION - BED
Page 1 of 7

1. Attach 1 x runner 7 to foot board 2 with 2 x bolts (D)
and 2 x spring washers (F) using allen key (H) and
tighten.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
PARTS
FITTINGS
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Do not rub or scrub the surface when cleaning.
• Do not put hot dishes directly on the surfaces of the item.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching
or damage.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
CARE INSTRUCTIONS
• For general cleaning, periodically dust with a soft cloth.
STEP ONE
D
F
Front
7
F
D
Page 2 of 7

1. Insert 3 x wooden dowels (A) to ladder side panel 5-
L.
2. Attach 3 x ladder shelves 10 to 1 x ladder side
panel 5-L with 6 x bolts (L) and tighten with a
screwdriver.
1. Insert 3 x wooden dowels (A) into ladder side panel
5-R.
2. Attach ladder side panel 5-R to the assembled unit
with 6 x bolts (L) and tighten with a screwdriver.
1. Insert 3 x wooden dowels (A) into head board 1.
2. Insert 4 x barrel nuts (E) into side panel 3 and side
panel 4.
3. Attach head board 1 to side panel 3 and side panel
4 with 4 x bolts (B),1 x bolt (C) and 5 x spring washers
(F) using allen key (H) and tighten.
STEP TWO
STEP THREE
STEP FOUR
5-L 10
10
10
5-R
5-L 10
10
10
Page 3 of 7

1. Insert 4 x wooden dowels (A) into foot board 2.
2. Insert 4 x barrel nuts (E) into side panel 3 and side
panel 4.
3. Attach foot board 2 to side panel 3 and side panel 4
with 4 x bolts(B), 2 x bolts (C) and 6 x spring washers
(F) using allen key (H) and tighten.
1. Insert 2 x wooden dowels (A) into side panel 4.
2. Attach ladder to side panel 4 with 2 x bolts (D) and
2 x spring washers (F) using allen key (H) and tighten.
3. Attach runner 6 to the assemble unit with 2 x bolts
(B) and 2 x spring washers (F) using allen key (H) and
tighten.
STEP SIX
STEP FIVE
D
Page 4 of 7

1.Attach 2 x slats 8 (these must be positioned at each
end of the bed base) and 14 x slats 9 to the
assembled unit with 64 x screws (G) and tighten with
a screwdriver.
2. Attach ladder to head board 1 with 2 x "L" metal
brackets (K) and 8 x screws (J).
The mark on the bed shows the maximum mattress
height position ,when putting on the mattress, it
should not be higher than this groove.
1. Attach bottom rail (11) to wooden runner 6 and 7
with 4 x screws (M) and tighten with screwdriver.
Position as shown
STEP NINE
STEP SEVEN
STEP EIGHT
6
7
Page 5 of 7

Next Retail Ltd, Desford Road, Leicester, LE19 4AT
PACKAGING LAYOUT
Page 6 of 7

Page 7 of 7