Next Rockwell User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the
item is found to be faulty. Should you need to return the unassembled product, please repack in the
original packaging.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
PRODUCT INFORMATION
• Upholstered with Fabric
• Fabric composition: 58% cotton, 42% viscose.
• Made in China.
CARE INSTRUCTIONS
• For general cleaning, periodically dust with a soft cloth.
• Clean regularly using a vacuum cleaner or clean soft brush.
• There may be indentations in the upholstery from the internal packaging; this will come out over time .
• Care should be taken to avoid spilling anything on the upholstery. If spillage occurs act promptly and
soak up any liquids by blotting with a clean absorbent cloth and allow to dry naturally. Never rub stains.
Never use a wet cloth.
• For dirty marks, use a dampened cloth with cold clean water. For more stubborn stains soak the cloth
first in soapy water: Use natural soap e.g. Lux flakes. Do not rub vigorously. Never use detergents or
abrasive cleaners.
• Avoid sharp objects that may damage the surface such as keys, buckles, coins etc .........
Rockwell Flip Storage
Page 1 of 6

FITTINGS
PARTS
Page 2 of 6

1. Attach the Right Side Rail (3) to headboard (1)
and footboard (2) using 4 x bolts (A) and 4 x
washers (K). Tighten with Spanner (G).
NOTE: Side rails are labelled right and left.
1. Attach the Left Side Rail (3) to headboard (1)
and footboard (2) using 4 x bolts (A) and 4 x
washers (K). Tighten with Spanner (G).
NOTE: Side rails are labelled right and left.
1. Put the 2 x Bottom Panel (4) inside the
bedframe
STEP ONE
STEP TWO
STEP THREE
Page 3 of 6

1. Unscrew the bolt on the Gas Lift Frame (5) ,
which is pre-fixed , then attach the end of Gas
lift by tighten back the screw by using Allen Key
(E)
1. Fix the Gas Lift Frame (5) onto the Side Rail by
using Allen Key( E) , Bolt (D) , Waser (L)
NOTE: Gas Lift Frame are labelled right and left.
1. Fix the "L" Metal (6) on Side Rail by using Bolt
( C ), Washer (K) , Allen Key (F)
STEP FOUR
STEP FIVE
STEP SIX
Page 4 of 6

1. Attach one of Tubing slat (10) with 2x Center
Rails (7) , 2x Centre Rail (9) and 1x Centre Rail ,
by using Allen Key (E) , Bolt (B) , Bolt (D) ,
Washer (L)
1. Attach another one of Tubing slat (10) with 2x
Center Rails (7) , 2x Centre Rail (9) and 1x Centre
Rail , by using Allen Key (E) , Bolt (B) , Bolt (D) ,
Washer (L)
1.Insert Slats (11) to Plastic Cap (J) & Plastic Cap
(I) ,afterwards insert the Cap to the holes of 2 x
Center Rail (7) , Center Rial (9)
STEP SEVEN
STEP EIGHT
STEP NINE
Page 5 of 6

1. Attach the slat frame to Gas Lift Frame
1. Attach the Fabric Pull Handle (12) at the end of
slat frame , see picture beside
Bed Assembly Completed
STEP TEN
YOUR BED IS NOW READY FOR USE
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 6 of 6