Next SLOANE BED 887928 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• Regular cleaning is essential to avoid build up of these products on the surface.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
PRODUCT INFORMATION
IMPORTANT
• We suggest you spend a short time reading through this leaet and then follow the simple step-by-step instruction
s.
• We recommend that the packaging is used to protect the surfaces during assembly.
•Foam is supplied to protect the front face. Do use the foam to protect the main face during assembly.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• Foam is supplied to protect the front face. Do use the foam to protect the main face during assembly.
"
• Please do not apply adhesive substrates to the product, e.g. sticky tape.
• Carefully check that you have all the parts before beginning assembly.
• All assembly xings should always be tightened properly and periodically check all xings and tighten if necessary.
• If a spillage does occur, blot any liquids immediately with a clean, dry absorbent cloth and allow to dry naturally.
• Clean periodically in situ using a professional cleaning company.
• For more stubborn stains a professional upholstery cleaner should be consulted.
• Avoid exposure to direct or prolonged periods of sunlight and position away from direct heat sources such as
radiators.
CARE INSTRUCTIONS
• Hair products such as hairsprays, oils and gels may aect the nish. Avoid prolonged contact with such products.
• Care should be taken to avoid spilling anything on the upholstery. If a spillage occurs act promptly and soak up any
liquids by blotting with a clean absorbent cloth. Never rub to remove stains. Never use a wet cloth.
• A minimum of 2 persons is required to assemble this product.
• Keep ttings out of children’s reach and keep children well away from construction area.
• Fabric content - 100%polyester.
•
Made in China.
SLOANE BED 887928
Page 1 of 8

1. Screw 2 x wings 2 to headboard 1 using 6 x bolts
(B), 6 x flat washers (H) and 6 x spring washers (I).
Tighten with Allen key (M).
STEP ONE
PARTS
FITTINGS
Page 2 of 8

1. Attach 2 x side rails 3 to headboard 1 using 4 x
bolts (A), 2 x dowel (E), 4 x half moon washers (F) and
4 x nuts (G). Tighten with Spanner (N).
1. Attach central support rail 5 to headboard 1 and
footboard 2 with 4 x bolts (C), 4 x flat washers (H) and
4 x spring washers (I). Tighten with Allen key (M).
STEP FOUR
STEP THREE
STEP TWO
2. Screw 2 x legs 6 to footboard 2 using 4 x bolts (C), 4
x flat washers (H) and 4 x spring washers (I). Tighten
with Allen key (M).
2. Attach 2 x side rails 3 to footboard 2 using 4 x bolts
(A), 2 x dowel (E), 4 x half moon washers (F) and 4 x
nuts (G). Tighten with Spanner (N).
3. Screw 2 x side rails to headboard 1 using 2 x bolts
(B), 2 x flat washers (H) and 2 x spring washer (I).
Tighten with Allen key (M).
Page 3 of 8

1. Insert slats 8 into end caps (L) and double end caps
(K) as shown.
2. Insert each end cap into corresponding holes in 2 x
side rails 3 and central support rail 5. Repeat process
for each slat.
NOTES:
* The curve of the slat must be facing upwards.
* Number of slats and caps vary dependant on size.
Note: Double 16 x Slats
King 16 x Slats
Super King 16 x Slats
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP SIX
STEP FIVE
STEP FIVE
2. Attach 2 x central support leg 7 to central support
rail 5 using 4 x bolts (D), 4 x nuts (G) and 8 x flat
washers (J). Tighten with a crosshead screwdriver
and spanner (N).
Page 4 of 8

Page 5 of 8

Page 6 of 8

Page 7 of 8

Page 8 of 8