Next SOPHIE 833978 User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• We recommend the use of the wall attachment bracket/strap provided for safety reasons.
• Made in China.
• For general cleaning, periodically dust with a soft cloth.
• Not suitable for use in bathrooms.
PRODUCT INFORMATION
• Made from MDF with a painted finish.
CARE INSTRUCTIONS
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
• Do not put hot dishes directly on the surfaces of the item.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
• Do not rub or scrub the surface when cleaning.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Wall fixings are not included.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
833978 SOPHIE DRESS SET
Page1of5

1. Insert 2x cambolts (A) into back panel 4.
2. Attach back panel 4 to bottom panel 3.
3. Insert 2 x camlocks (B) to bottom panel 3, ensure
the arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
1. Insert 2 x wooden dowel (C) into Shelf Panel 3.
2. Attach middle divider panel 5 to shelf panel 3
with 2 x screws (M) and tighten with a screwdriver.
FITTINGS
PARTS
STEP TWO
STEP ONE
(9) Drawer Bottom
Panelx 2
(7) Drawer Back
Panel x 2
3
Page2of5

1. Insert 2 x wooden dowel (C) and 4x cambolts (A)
to side panel 2-L.
2. Attach side panel 2-L to back panel 4 and bottom
panel 3.
3. Insert 4 x camlocks (B) to bottom panel 3 and
back panel 4, ensure the arrow indicator is pointing
towards the panel edge before tightening with a
screwdriver.
4. Attach back panel 4 to divider panel 5 with 2 x
screws ( L ) and tighten with a screwdriver.
1. Insert 2 x wooden dowel (C) and 4x cambolts (A)
to side panel 2-R.
2. Attach side panel 2-R to back panel 4 and shelf
panel 3.
3. Insert 4 x camlocks (B) to bottom panel 3 and
back panel 4, ensure the arrow indicator is pointing
towards the panel edge before tightening with a
screwdriver.
1. Insert 4 x wooden dowel (C) and 8 x cambolts (A)
to top panel 1.
2. Attach top panel 1 to side panel 2-l ,side panel 2-R
and middle divider 5.
3. Insert 8x Camlocks (B) to Side Panel 2 (both L&R)
and Divider Panel 5 and tightening with a
screwdriver.
STEP THREE
STEP FOUR
STEP FIVE
2-L
C
B
1
2-R
C
3
4
Page3of5

1. Attach drawer side panels 8 (both L&R) to drawer
back panel 7 with 4 x Screws (D) and tighten with a
screwdriver.
2. Insert the drawer bottom panel 9 into grooves of
drawer side panels 8(both L&R).
3. Insert 2 x cambolts (A) and 2 x wooden dowels ( C
) into drawer front panel 6-R.
4. Attach drawer front panel 6-R to the assembled
drawer frame.
5. Insert 2x camlocks (B) into drawer side panels 8
(both L&R) and tighten with a screwdriver.
6. Attach 1 x handle ( F ) to drawer front panel 6-R
with 1 x screws (E) and tighten with a screwdriver.
8. Repeat with remaining panels7,8,9 &6-L to
produce the left drawer.
1. Insert drawers into the desk on the pre-fitted
runners.
STEP SEVEN
STEP SIX
1. Attach seat panel 10 to chair back panel 11 with 4
x screws( H ), 4 x washers ( J ) and 4 x spring
washers ( K )and tighten with a screwdriver.
STEP EIGHT
HJ
H
Page4of5

1. Insert round rod 13 ( x 2 ) into chair legs 12(both
L&R
)
.
2. Attach chair legs 12 ( both L&R) and round rods
13 (x 2) to the assembly.
1. Insert 4 x screws ( H ), 4 x spring washers ( K )
and 4 x washers ( J ) through the brackets of seat
panel 10 and tighten with screwdriver.
2. Insert 4 x Screws ( M ) into round rods 13 and
tighten with a screwdriver.
1.Use screw C and washer B to secure the nylon
strap A to the top panel.
2.Secure the other end of the strap to the wall with
an appropriate screw and wall plug for your wall
type. To hide the strap behind the unit, drill the
holes lower than the top of unit.
Warning :Always ensure the area to be drilled is free
from hidden electrical wires, water and gas pipes.
NB:Wall fixings are not included-please source
suitable fixings for your wall type. If in doubt please
STEP TEN
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP ELEVEN
STEP NINE
10
11
12-R
12-L
STRAP TOP
WASHER
SCREW
WALL
Page5of5