Next SOPHIE 836023 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• Made from MDF with a painted finish.
• Made in China.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
PRODUCT INFORMATION
• Do not put hot dishes directly on the surfaces of the item.
CARE INSTRUCTIONS
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Wall fixings are not included.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
• We suggest you spend a short time reading through this leaflet and then follow the simple step by step instructions.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching
or damage.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
• We recommend the use of the wall attachment bracket/strap provided for safety reasons.
• Do not rub or scrub the surface when cleaning.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• For general cleaning, periodically dust with a soft cloth.
836023 SOPHIE CHEST
Page 1 of 7

1. Insert 2 x wooden dowels (C) into top panel 1.
2. Attach top front rail 10 to top panel 1 with 3 x
screws (F) and tighten with a screwdriver.
FITTINGS
PARTS
STEP ONE
(5) Back Panel x 1(4) Back Panel x 1
(17) Drawer Front
Panel x 3
(14) Drawer Side
Panel(L/R) x 4 (19) Drawer Side Panel(L/R) x 6
J x 2
C x 26 H x 7
J x 2
C x 26 H x 7
Page 2 of 7

1. Insert 2 x wooden dowels (J) into bottom frame 7.
2. Attach lower front rail 11 to bottom frame 7 with 3 x
screws (F) and tighten with a screwdriver.
1. Insert 4 x wooden dowels (C) into shelf panel 6.
2. Attach middle divider panels 3 (x2) to shelf panel 6
with 4 x screws (E) and tighten with a screwdriver.
1. Insert 2 x wooden dowels (C) and 2 x cambolts (A)
into side panel 2-L.
2. Attach shelf panel 6 to side panel 2-L.
3. Insert 2 x camlocks (B) into shelf panel 6. Ensure
the arrow indicators are pointing towards the panel
edge before tightening with a screwdriver.
STEP TWO
STEP THREE
STEP FOUR
3
3
6
Page 3 of 7

1. Insert 2 x wooden dowels (C) and 2 x cambolts (A)
into Side Panel 2-L.
2. Attach shelf panel 8 and back rail 9 to side panel 2-
L.
3. Insert 2 x camlocks (B) into shelf panel 8 and back
rail 9. Tighten the camlocks with a screwdriver.
1. Insert 4 x wooden dowels (C) and 4 x cambolts (A)
into side panel 2-R.
2. Attach side panel 2-R to the assembled
components.
3. Insert 4 x camlocks (B) into shelf panel 6, shelf
panel 8 and back rail 9. Tighten all camlocks with a
screwdriver.
1. Insert 4 x wooden dowels (C) into bottom frame 7.
2. Attach bottom frame 7 to the assembled
components with 4 x screws (E) and tighten with a
screwdriver.
STEP FIVE
STEP SIX
STEP SEVEN
9
Page 4 of 7

1. Insert 8 x wooden dowels (C) and 8 x cambolts (A)
into top panel 1.
2. Attach top panel 1 to the assembled components.
3. Insert 8 x camlocks (B) into side panel 2-L, side
panel 2-R and middle divider panels 3 (x2). Tighten all
camlocks with a screwdriver.
1. Insert back panel 4 and back panel 5 to the
assembled chest.
2. Secure panels with 16 x screws (D) and tighten with
a screwdriver.
1. Attach drawer side panels 14 (both L&R) to drawer
back panel 13 with 4 x screws (F).
2. Attach support slat 16 to drawer back panel 13 with
2 x screws (F), make sure that the camlock hole in the
support slat 16 is facing downwards.
3. Insert the drawer bottom panel 15 into the grooves
of drawer side panels 14 (both L&R).
4. Insert 5 x cambolts (A) into drawer front panel 12.
5. Attach drawer front panel 12 to the assembled
drawer frame.
6. Insert 5 x camlocks (B) into drawer side panels 14
(both L&R) and support slat 16. Ensure the arrow
indicators are pointing towards the panel edges
before tightening with a screwdriver.
7. Attach 2 x handles (H) to drawer front panel 12 with
2 x screws (G) and tighten with a screwdriver.
8. Repeat with remaining panels 12, 13, 14, 15 &16 to
produce the second drawer.
STEP EIGHT
STEP NINE
STEP TEN
D4
D
D
D
D
D
D
D
D
D
Page 5 of 7
15