Next STANTON 133228 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to
be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
STANTON CORNER DESK AND SHELF
STANTON CORNER DESK AND SHELFSTANTON CORNER DESK AND SHELF
STANTON CORNER DESK AND SHELF
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not put hot dishes directly on the surfaces of the item.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching
or damage.
• Do not use furniture polish.
• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
CARE INSTRUCTIONS
• Made in China.
• A minimum of two persons is required to assemble this product.
• Made from honeycomb board,particle board & MDF with a wood effect finish.
PRODUCT INFORMATION
• We recommend that the packaging is used to protect the surfaces during assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
Page 1 of 6

FITTINGS
PARTS
1.Insert 10x cambolts (D) into panels 2, 3 & 5
and tighten with a screwdriver.
1.Glue (B) and insert 2 x wooden dowels (A) into
panel 2.
2.Attach panel 4 to panel 2
3.Insert 2x camlocks (C ) into panels 4 and
tighten with a screwdriver.
4. Glue and insert 4 x wooden dowels (A) into
panels 3 & 5.
5.Attach panel 3 & 5 to panels 6 (x2)
6.Insert 8x camlocks (C ) into panels 6 (x2)
tighten with a screwdriver.
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver
STEP TWO
STEP ONE
Page 2 of 6

1.Insert 5x cambolts (D) into panel 1 and tighten
with a screwdriver.
2. Attach metal plate (G) to leg 13 with 1x bolts (E)
using an Allen key (F) to tighten.
3.Insert 2 x bolts (K) into nuts fixed on panel 1
and turn bolts (K) clockwise until tight by hands.
1. Attach leg 13 to panel 1 with 4 x bolts (E)
using an Allen key (F) to tighten.
2.Glue (B) and insert 7 x wooden dowels (A) into
panel 1.
3.Attach panels 2 & 4 to panel 1.
4.Attach panels 3 & 5 to panel 1.
5.Insert 5x camlocks (C ) into panels 2,4 & 5.
tighten with a screwdriver.
Ensuring the arrow indicator is pointing towards
STEP THREE
STEP FOUR
the panel edge before tightening with a
screwdriver
6.Cover 2 x metal pieces (L) onto 2 x bolts (K)
and thread 2 x springs (N) onto bolts (K) then
screw 2 x metal nuts (J) with spanner (I)
1. Carefully lift the unit upright. The unit should be
lifted by two people.
2. Use 4X stickers (H) to cover the camlock holes
on panels 2 , 5
3. Use 2X stickers (M) to cover the holes
on panel 3
STEP FIVE
Page 3 of 6

1.Insert 8x cambolts (D) into panels 7 & 8 and
tighten with a screwdriver.
1.Glue (B) and insert 8 x wooden dowels (A) into
panel 7.
2. Attach panels 10,12 & 11(x2) to panel 7
3. Insert 4 x camlocks (C) into panels 10,12 & 11(x2)
tighten with a screwdriver.
Ensuring the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver.
STEP SEVEN
STEP SIX
1.Slide panel 9 into the grooves on the panels 10 & 12
unit as shown in diagram.
STEP EIGHT
Page 4 of 6

1.Glue (B) and insert 8 x wooden dowels (A) into
panel 10,12 & 11(x2)
2. Attach panel 8 to panels 10,12 & 11(x2)
3. Insert 4 x camlocks (C) into panels 10,12 & 11(x2)
tighten with a screwdriver.
Ensuring the arrow indicator is pointing toward
the panel edge before tightening with a
screwdriver
1. Use 8Xstickers (H) to cover the camlock holes
on panels 10,12 & 11(x2)
STEP NINE
STEP TEN
NB: Place the template over the back of
the shelf to ensure that the holes match
the position of the hooks before drilling
into your wall.
1.Use template (O) provided to mark on the wall
the position of wall-mounted fixings.
2.Use a spirit level to check that the fixings are
level and straight.
STEP ELEVEN
Page 5 of 6

Warning:
Always ensure intended wall area to be
drilled is free from hidden electrical wires,
water and gas pipes.
NB: Wall fixings are not included - please
source suitable fixings for your wall type.
If in doubt please consult a qualified
trades person.
1.Drill holes and insert the wall plugs and the screws
into the wall. Tighten the screws, leaving the screw
head exposed by about 1/4 inch (6mm).
2.Carefully lift the shelf into position ensuring that the
fixings attached to the shelf are firmly hooked over the
exposed screws.
3.Check shelves periodically to see that no fittings as
loosened and needs attention.
STEP TWELVE
1.The diagram for your reference .
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP FOURTEEN
Page 6 of 6