Next Sussex 786032 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings plase contact Customer
Services Tel: [phone]
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
• Care should be taken to avoid spilling anything on the upholstery. If spillage occurs act promptly and soak up any
liquids by blotting with a clean absorbent cloth and allow to dry naturally. Never rub stains. Never use a wet cloth.
• Avoid sharp objects that may damage the surface such as keys, buckles, coins etc .........
• Do not allow pets on leather upholstery.
CARE INSTRUCTIONS
• For general cleaning, periodically dust with a soft cloth.
• Clean reguarly using a vacuum cleaner or clean soft brush.
• There may be indentations in the upholstery from the internal packging; this will come out over time .
• For dirty marks, use a dampened cloth with cold clean water. For more stubborn stains soak the cloth first in soapy
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
PRODUCT INFORMATION
• Fabric composition: 58% cotton, 42% viscose.
• Made in China.
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
Sussex Storage bed
786032

BED FITTINGS
DRAWER FITTINGS

BED PARTS
DRAWER PARTS

Attach Supporting Legs (7)X2 to Supporting Tube
(5) by using Bolts (B), washer (L) , adjustable feet (
H) and Allen key (E).
Attach headboard (1)and footboard (2) to siderails (3)
using Spanner (G),washer (K) and bolt (A).
Attach headboard (1)and footboard (2) to siderails (3)
using Spanner (G),washer (K) and bolt (A).
STEP ONE
STEP TWO
STEP THREE

Fix supporting tube (6) with siderials by using Allen key
(E) , Bolt (D) and washer (L)
Note : need a screw driver , which is not provided
Attach the Supporting Tube (5) to Headboard
( 1 ) and Footboard (2) by using Allen Key ( F )
and bolt ( D ) and washer (K)
Assemble drawer by using left side panel (11) ad
right side panel(10) and Back panel (12) , with tools
Rafix Cam Bolt (M) x 4 and Cam (N)x 4
STEP SIX
STEP FOUR
STEP FIVE

Note : need a screw driver , which is not provided
Insert Bottom plateboard (9)
Fix Front Panel (13) by using Rafix Cam Bolt (M) x 7 and
Cam (N)x7
Note : need a screw driver , which is not provided
STEP SEVEN
STEP EIGHT
STEP NINE
Attach the Lathing (14) to Back panel (12) by using
Rafix Cam Bolt (M) x 6 and Cam (N)x 6

Insert the assembled drawer into the bed frame
1. Insert Sprung Slats (8) into the Straps (4).
2. Insert Sprung Slats (8) into Caps ( I ).
5. Repeat the step 1-4 accordingly until the end.
Assemble the sprung slats as following.
3. Insert Caps ( I ) completed with Sprung Slats (8)
into corresponding holes on Side Rail (3).
4.Insert the other end of Slats (8) into Cap ( J ) and
lock into centre rail (5)
STEP TEN
STEP ELEVEN

IMPORTANT
Once the feet have been assembled and attached,
they should be adjusted to ensure they do not touch
the floor, (5mm above the floor) to allow for
movement once the mattress is placed on the bed
frame.
It is important to note that when moving the bed that
it is not dragged into its new position to prevent the
possibility of these feet being twisted or angled to
one side, which could lead to the collapse of the
centre of the bed.
To move the bed, remove the mattress and lift the
bed into its new position to avoid damage. Ensure
YOUR BED IS NOW READY FOR USE
Next Retail Ltd, Desford Road, Leicester, LE19 4AT