Ni Pxie-1487 Owner's manual

SAFETY, ENVIRONMENTAL, AND REGULATORY INFORMATION

PXIe-1487

FlexRIO GMSL Interface

Read this document before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring

instructions in addition to requirements of all applicable codes, laws, and standards. Visit ni.com/manuals for more information about your product, including

specifications, pinouts, and instructions for connecting, installing, and configuring your system.

Regulatory Icons

Notice Take precautions to avoid data loss, loss of signal integrity, degradation of performance, or damage to the product.

Caution Take precautions to avoid injury. Consult the product documentation for cautionary statements when you see this icon printed on the

product. Cautionary statements are localized into French for compliance with Canadian requirements.

Safety

Caution Observe all instructions and cautions in the user documentation. Using the product in a manner not specified can damage the product and

compromise the built-in safety protection. Return damaged products to NI for repair.

Attention Suivez toutes les instructions et respectez toutes les mises en garde de la documentation d'utilisation. L'utilisation du produit de toute autre

façon que celle spécifiée risque de l'endommager et de compromettre la protection de sécurité intégrée. Renvoyez les produits endommagés à NI pour

réparation.

Safety Compliance Standards

This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:

• IEC 61010-1, EN 61010-1

• UL 61010-1, CSA C22.2 No. 61010-1

Note For safety certifications, refer to the product label or the Product Certifications and Declarations section.

EMC Guidelines

This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (EMC) stated in the product specifications.

These requirements and limits provide reasonable protection against harmful interference when the product is operated in the intended operational

electromagnetic environment.

This product is intended for use in commercial and light-industrial locations. However, harmful interference may occur in some installations, when the product

is connected to a peripheral device or test object, or if the product is used in residential areas. To minimize interference with radio and television reception and

prevent unacceptable performance degradation, install and use this product in strict accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved by NI could void your authority to operate it under your local regulatory

rules.

EMC Notices

Refer to the following notices for cables, accessories, and prevention measures necessary to ensure the specified EMC performance.

Notice For EMC declarations and certifications, and additional information, refer to the Product Certifications and Declarations section.

Notice Changes or modifications to the product not expressly approved by NI could void your authority to operate the product under your local

regulatory rules.

Notice The performance of this product can be disrupted if subjected to Electrostatic Discharge (ESD) during operation. To prevent damage,

industry-standard ESD prevention measures must be employed during installation, maintenance, and operation.

Notice Operate this product only with shielded cables and accessories.

Notice The length of all I/O cables must be no longer than 15.0 m (49 ft).

Electromagnetic Compatibility Standards

This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use:

• EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity

• EN 55011 (CISPR 11): Group 1, Class A emissions

• AS/NZS CISPR 11: Group 1, Class A emissions

Note Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency

energy for the treatment of material or inspection/analysis purposes.

Note In Europe, Australia and New Zealand (per CISPR 11), Class A equipment is intended for use only in non-residential locations.

Environmental Guidelines

Notice This product is intended for use in indoor applications only.

Environmental Characteristics

Temperature

Operating 0 °C to 55 °C

Storage -40 °C to 71 °C

Humidity

Operating 10% to 90%, noncondensing

Storage 5% to 95%, noncondensing

Pollution Degree 2

Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient temperature)

Shock and Vibration

Operating vibration 5 Hz to 500 Hz, 0.3 g RMS

Non-operating vibration 5 Hz to 500 Hz, 2.4 g RMS

Operating shock 30 g, half-sine, 11 ms pulse

Environmental Management

NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous

substances from our products is beneficial to the environment and to NI customers.

For additional environmental information, refer to the Commitment to the Environment web page at ni.com/environment. This page contains the environmental

regulations and directives with which NI complies, as well as other environmental information not included in this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers At the end of the product life cycle, all NI products must be disposed of according to local laws and regulations. For more

information about how to recycle NI products in your region, visit ni.com/environment/weee.

电子信息产品污染控制管理办法（中国 RoHS）

540

NI 符合中国电子信息产品中限制使用某些有害物质指令(RoHS)。关于 NI 中国 RoHS 合规性信息，请登录 ni.com/

environment/rohs_china。(For information about China RoHS compliance, go to ni.com/environment/rohs_china.)

Environmental Standards

This product meets the requirements of the following environmental standards for electrical equipment.

• IEC 60068-2-1 Cold

• IEC 60068-2-2 Dry heat

• IEC 60068-2-78 Damp heat (steady state)

• IEC 60068-2-64 Random operating vibration

• IEC 60068-2-27 Operating shock

Note To verify marine approval certification for a product, refer to the product label or visit ni.com/certification and search for the certificate.

2| ni.com | PXIe-1487 Safety, Environmental, and Regulatory Information

Power Requirements

Note Power requirements are dependent on the contents of the LabVIEW FPGA VI used in your application.

Note Do not position product so that it is difficult to disconnect power.

Voltage rating 3.3 V

12 V

Current/power rating 3 A 3.3 V

6 A at 12 V

External power supply

Voltage rating 9 V to 30 V

Current/power rating 800 mA per channel, up to 8 channels

Total power 82 W, maximum

Physical

Dimensions 3U, two-slot PXI Express module, 21.6 cm × 4.1 cm × 13.0 cm

(8.5 in. × 1.6 in. × 5.1 in.)

Weight 692 g (24.38 oz)

Export Compliance

This product is subject to control under the U.S. Export Administration Regulations (15 CFR Part 730 et. seq.) administered by the U.S. Department of

Commerce's Bureau of Industry and Security (BIS) (www.bis.doc.gov) and other applicable U.S. export control laws and sanctions regulations. This product

may also be subject to additional license requirements of other countries' regulations.

Additionally, this product may also require export licensing before being returned to NI. The issuance of a Return Material Authorization (RMA) by NI does

not constitute export authorization. The user must comply with all applicable export laws prior to exporting or re-exporting this product. See ni.com/legal/

export-compliance for more information and to request relevant import classification codes (e.g. HTS), export classification codes (e.g. ECCN), and other

import/export data.

Product Certifications and Declarations

Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for NI

products, visit ni.com/product-certifications, search by model number, and click the appropriate link.

NI Services

Visit ni.com/support to find support resources including documentation, downloads, and troubleshooting and application development self-help such as

tutorials and examples.

Visit ni.com/services to learn about NI service offerings such as calibration options, repair, and replacement.

Visit ni.com/register to register your NI product. Product registration facilitates technical support and ensures that you receive important information updates

from NI.

NI corporate headquarters is located at 11500 N Mopac Expwy, Austin, TX, 78759-3504, USA.

PXIe-1487 Safety, Environmental, and Regulatory Information | © National Instruments Corporation | 3

Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on NI trademarks. Other product

and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering NI products/technology, refer to the appropriate

location: Help»Patents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find information

about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/

legal/export-compliance for the NI global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO

EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.

Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set

forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.