Night & Day Furniture Ginger Twin Full Bunk Bed User manual

Page 1 of 9
N&D 0809
Ginger Twin Full Bunk Bed
A s s e m b l y I n s t r u c t i o n s
TM
Certified:
This bunk bed conforms to all applicable consumer product safety standards
16 CFR PARTS 1213, 1500, 1513 and ASTM F-1427
Replacement Parts:
Replacement parts, including additional guardrails may be obtained from any
Night & Day Furniture Dealer.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
SAFETY WARNING
!
Follow the information on the warnings appearing on the upper bunk end structure and on
the carton. Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both, to help prevent
the likelihood of entrapment or falls.
Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other components are in their
proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Prohibit more than one person on upper bunk.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and wall.
The use of water or sleep flotation mattresses is prohibited.
STRANGULATION HAZARD–Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to hooks, belts
and jump ropes.
Keep these instructions for future reference.
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress, which is 37 1/2" - 38 1/2" width and 74"-75" long on upper bunk (twin size.)
Ensure that the thickness of the mattress does not exceed 6" and that the mattress surface is at
least 5" (127mm) below upper edge of guardrails.
WARNING:
Adult Assembly Required. This package contains small parts. Keep away from children.

Parts in Box 5
Parts in Box 11A
Page 2 of 9
Hardware in this Box.
1B
Parts in Box 3
Ginger Twin Full Bunk Bed
A s s e m b l y I n s t r u c t i o n s
Parts in Box 4
Parts in Box 2
Note:
Tools required for assembly:
Allen Key (provided)
Phillips Screwdriver (not provided)
N&D 1109
Lower Bunk
(Left Hand) x 1
Lower Bunk
(Right Hand) x 1
Upper Bunk
(Right Hand) x 1
Note: No Holes!
Upper Bunk
(Left Hand) x 1
Brackets x 4
Upper Stretcher (with extra holes) x 1
Ladder x 1
Rear Guard Rail x 1
Front Guard Rail x 1
Stretchers x 3
Middle Rail x 1
Set of Slats x 1
(Upper Bunk)
Set of Slats x 1 (Lower Bunk)
90mm Bolts
x 19
40mm Threaded
Wood Bolts x 8
Metal Tubes
x 4
Long Allen Key
x 1
30mm Wood
Screws x 36
16mm Wood
Screws x 2
Barrel Nuts
x 23
30mm Bolts
x 2
60mm Bolts
x 16
Wood Dowels
x 27
40mm Bolts
x 4

Page 3 of 9
Use 2 People!
Please Note:
Be sure the holes are free of wood chips
and saw dust.
Bolt and Barrel Nut Assembly.
Do not force the Bolt as you may strip the
thread. Be sure the thread is properly started.
Attach Stretchers and the Middle Rail to the Lower Bunks.
Fit Wood Dowels to the
Stretchers.
2A
Fit Wood Dowel to the
Middle Rail.
2C
2B
Ginger Twin Full Bunk Bed
A s s e m b l y I n s t r u c t i o n s
N&D 0808
THIS END
FRONT
Barrel Nuts
90mm
Bolts
90mm
Bolts
Stretcher
90mm
Bolts
Barrel Nuts
60mm
Bolts
Middle Rail
Lower Bunk
(Right Hand)
Lower Bunk
(Left Hand)
Stretcher
Note: The Left hand Bottom Bunk has
extra holes which assemble towards
the front.
Note: The Right hand Bottom Bunk
has extra holes which assemble
towards the front.
Wooden Dowels
Middle Rail
Middle
hole
Wooden Dowels
Stretcher
Middle
holes

Fit the Long Slats between the Stretchers.
Page 4 of 9
Lay the Slats inside the Stretchers as shown below,and Bolts
in place with 40mm Threaded Wood Bolts
(total 4 Bolts)
3A
Use the wood screws to fix the remaining
slats to the Stretchers (total 18 screws).
An electric screwdriver will make this
much easier.
Fix the Remaining Slats with screws.
3B
Ginger Twin Full Bunk Bed
A s s e m b l y I n s t r u c t i o n s
N&D 0207
Stretcher
Lower Bunk
40mm Threaded
Wood Bolt
Wood Screws
Wood Screws
Middle Rail
40mm Threaded
Wood Bolt 40mm Threaded
Wood Bolt
40mm Threaded
Wood Bolt
Wood Screws

Be sure the holes are free of wood chips
and saw dust.
Bolt and Barrel Nut Assembly.
Do not force the Bolt as you may strip the
thread. Be sure the thread is properly started.
Use 2 People!
Please Note:
Tap Wooden Dowels into the ends of the Stretchers and Rear
Guard Rail. Using 90mm Bolts and Barrel Nuts, attach these to
the Upper Bunk, carefully noting Left and Right hand sides.
Attach the Stretchers and Rear Guard Rail to the Upper Bunks.
4A
Page 5 of 9
Ginger Twin Full Bunk Bed
A s s e m b l y I n s t r u c t i o n s
N&D 0808
Wooden
Dowel
Wooden
Dowels
Wooden
Dowels
Upper Bunk
(Left Hand)
Upper Stretcher
with Extra Holes
90mm
Bolts Barrel
Nuts
Barrel
Nuts
Rear Guard Rail
Upper Bunk
(Right Hand)
Note:
Extra Holes
Note: No
Holes Here! 90mm
Bolts
90mm
Bolts
90mm
Bolt

Tap Wooden Dowels into the ends of the Front Guard Rail. Use
the 90mm Bolts and Barrel Nuts fix it in place. The Front Guard
Rail attaches to the Stretcher using the 30mm Bolts.
Page 6 of 9
5A Attach the Front Guard Rail to the Upper Bunk.
Ginger Twin Full Bunk Bed
A s s e m b l y I n s t r u c t i o n s
N&D 0808
Front Guard Rail
30mm
Bolts
Front Guard Rail Stretcher
Barrel Nut
Wooden
Dowels
90mm
Bolt
Front Guard Rail

Use the wood screws to fix the remaining
slats to the Stretchers (total 18 screws.)
An electric screwdriver will make this
much easier.
Bolt the short Slats to the Stretchers.
Page 7 of 9
Lay the Slats inside the Stretchers as shown below, and Bolt in
place with the 40mm Threaded Wood Bolts (total 4 Bolts.)
6A Fix the Remaining Slats with screws. 6B
Ginger Twin Full Bunk Bed
A s s e m b l y I n s t r u c t i o n s
N&D 0207
40mm Threaded
Wood Bolt
40mm Threaded
Wood Bolt 40mm Threaded
Wood Bolt
Wood Screws
Wood Screws
Wood Screws

Use 2 People!
Please Note:
Fit the Metal Tubes into the holes on the top of the Upper Bunk.
Carefully Lift the Top Bunk onto the Lower Bunk.
7A Fit the Upper Bunk onto the Lower Bunk. Fit the Brackets to the Legs.
7B
Page 8 of 9
Use the 60mm Bolts to fix the Brackets to the
Uppper Bunk and 40mm Bolts to the Lower Bunk.
Ginger Twin Full Bunk Bed
A s s e m b l y I n s t r u c t i o n s
N&D 0207
Metal Tubes
Metal Tubes 60mm
Bolts
60mm
Bolts
40mm
Bolts
60mm
Bolts
Lower Bunk

Page 9 of 9
Ginger Twin Full Bunk Bed
A s s e m b l y I n s t r u c t i o n s
8A Attach the Ladder to the Upper Stretcher.
Finally, hook on the Ladder onto the Upper
Stretcher. Use the 16mm Wood Screws to fix
the Ladder in place.
Please take note of the warnings shown on
page one of these instructions, printed on the
carton box and on stickers on the Bunk bed.
N&D 0207
Ladder
Stretcher
16mm
WoodScrews