I368-K 1811
Niigata seiki Co., Ltd.
6-15-22, Tsukanome, Sanjo, Niigata, Japan, 955-0055
Tel. : +81-256-31-5670 Fax. : +81-256-39-7730
MAIL:intl.sales@niigataseiki.co.jp
URL http://www.niigataseiki.co.jp
INSERTING・REPLACING BATTERY
AFTER USE CARE・STORAGE
TROUBLESHOOTING PRODUCT SPECIFICATIONS
SERVICE
●After use, wipe off any dirt or oil from measuring
surfaces, sliding surfaces, and exterior using a dry
cloth and perform rust prevention treatment.
For rust prevention, lightly apply anti-rust oil, or place in rust
preventive bag.
●Store with Lock Screw loosened.
If stored with Lock Screw tight, expansion due to temperature
changes may cause excessive force which will cause inaccuracy.
●Store in a cool, dry, and dark location in the provided
case.
Keep out of direct sunlight and moisture, and please keep
secure from unauthorized personnel.
●Remove battery if Caliper will not be used for a long
period of time.
PREPARATION FOR USE
Before using the calipers, please follow the steps below:
●Wipe off rust proofing and dirt from measuring
surfaces and slide.
Contamination of surfaces may cause measurement error.
●Allow the calipers and object to be measured time to
reach the same temperature.
A temperature difference between the object to be measured
and the caliper may cause measurement error. Allow enough
time for the temperatures to equilibrate.
HOW TO USE
■Power ON/OFF
①To turn on, press the [ON/OFF]Button.
②To turn off, press the [ON/OFF]Button.
③With power on, press the [HOLD]Button to fix the value on the
display.
■Absolute Measurement Mode
①Loosen the lock screw, and turn on power.
②With jaws closed and Probe Tips touching, press the [ZERO]
Button.
③When “0.00mm”is displayed on LCD, Calipers is ready to start
measurement.
■Comparisons Measure Mode
①Loosen the lock screw, and turn on power.
②With Probe Tips open to desired reference position (any point
is OK,)press [ZERO]Button.
③When “0.00mm”is displayed on LCD, Calipers is ready to start
measurement.
Q. Nothing is displayed on LCD.
A. The battery may be running low, please replace battery
with a new one.
Q. With power on, the number on the LCD does not change
as Display Unit is moved.
A. Please reset by removing battery for about 30sec., and
then replacing.
Q. Nothing happens when buttons are pressed.
A. Make sure battery is properly inserted.
Q. The characters “MIN”, “MAX”, or “△”are displayed on LCD.
A. Cycle power, or apply several long presses to [HOLD]
Button. Use as normal once character is off.
Q. The correct value is not displayed.
A. High humidity may cause dampness. Please dry off the
instrument and use only in dry location. ●Resolution : 0.01mm
●Display : 5 Digit LCD
●Auto Off : approx. 20 min.
●
Maximum response speed
: Slide to Right .....1.5 m/s
Slide to Left .......0.75 m/s
※Left/Right as shown in diagram at top of manual.
●Operating Temperature Range : 0°C~40°C
●Storage Temperature Range : −10°C~60°C
●Power : (1x)CR2032 Lithium Battery
●Battery Life : approx. 2.5 years in normal use
●Accessory : CR2032 Lithium Battery (for test)
①Slide cover in direction of arrow.
②Insert battery with (+)side outward.
③Replace battery cover.
●
Use care to avoid damaging
terminals when inserting
battery.
●Terminals may be broken if battery is pressed straight down.
●Insert battery at angle, underneath the small hook, as shown.
Use only CR2032 type
battery.
Battery
Cover
Remove
Notice
Hook
Slide In
※Not including quantization error (±1 count)
●If Instrument is not working properly, or if you have any
questions, please contact distributor or place of purchase.
●Please note, manufacturer is unable to respond to inquires or
provide service directly. Please contact distributor or place of
purchase.
Battery
Battery
Pressed Down
Accuracy※±0.03mm
±0.04mm
Measuring Range
0
-
150mm
0
-
200mm
Weight
200g
230g
Model No.
GDCS
-
150NP
GDCS
-
200NP
Terminals
Terminals
