Ninja BL682NZ User manual

®BL682NZ
OWNER’S GUIDE

1CUSTOMER CARE - NZ: 0800 002 999
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
OR INJURY:
1. CAUTION: The blades are not affixed to
the unit. They are removable and extremely
sharp. When handling the stacked blades or
the chopping blades, do not hold the blades
but rather always hold the shaft. Blades are
sharp. Handle carefully!
2. CAUTION: DO NOT BLEND HOT LIQUIDS.
3. CAUTION: DO NOT process hot foods or
hot liquids. Allow hot ingredients to cool
beforeprocessing.
4. To protect against electrical shock, do not
submerge the appliance or allow the power
cord to come into contact with water or any
otherliquid.
5. DO NOT allow young children to operate the
appliance or use as a toy. Close supervision
is necessary when any appliance is used near
children.
6. Never leave an appliance unattended when in
use.
7. Turn the appliance off and remove the power cord
from the electrical outlet when not in use, before
assembling or disassembling parts, accessing
parts that move while in use and before cleaning.
To unplug, grasp the plug and pull from the
electrical outlet. Never pull from the power cord.
8. DO NOT abuse the power cord. Never carry
the appliance by the power cord or yank it to
disconnect from electrical outlet; instead, grasp
the plug and pull to disconnect.
9. DO NOT use with damaged cord or plug. Contact
Customer Services or Service Center for the
repair or replacement of the line cord.
WHEN USING ELECTRICAL APPLIANCES,
BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE
USING YOUR NUTRI NINJA™
| NINJA®
BLENDER SYSTEM WITH AUTO-iQ™
TECHNOLOGY.
WARNING: Extension cords are not
recommended for use with this product.
WARNING: The blades are not affixed to
the unit. They are removable and very sharp.
Handle with care!
CAUTION: In order to avoid a hazard due to
inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through
an external switching device, such as a
timer, or connected to a circuit that is
regularly switched on and off by the utility.
IMPORTANT: This appliance is not intended
for use by persons with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
Children shall not use or play with this
appliance. Close supervision is necessary to
keep appliance and cord out of reach of children
during use.

2CUSTOMER CARE - AU: 1800 890 840
23. Extreme caution must be used when moving an
appliance containing hot food, water or other liquids.
24. DO NOT overfill. DO NOT exceed “MAX” fill line.
25. DO NOT operate the appliance empty.
26. To reduce the risk of burns, always allow the
appliance to cool before taking off parts and
before cleaning.
27. Max ON time is 60 seconds under 1500W load.
If the appliance overheats, a thermal switch will
become activated and shut off the motor. To
reset, unplug the appliance and let it cool down
for approximately 15 minutes before using again.
28. In the event that the unit overloads, the control
panel lights will flash and the unit will shut down.
Unplug the appliance and let it cool down for
approximately 15 minutes before using again.
29. Max PULSE iteration is 30 Pulses. After 30
Pulses allow 10 minutes to pass before running
the PULSE function up to an additional 30 Pulses.
30. The maximum rating is based on the stacked
blade (pitcher) that drives the greatest power
and other recommended attachments may draw
significantly less power or current.
31. To avoid injury, never attempt to place the Pro
Extractor Blade™onto the motor base without
first assembling the blade assembly to the Nutri
Ninja™Cup.
32. DO NOT push food into the food chute with your
fingers. Always use the food pusher provided.
33. Appliance accessories are not intended to
be used in the microwave as it may result in
damage to the accessories.
34. THIS PRODUCT IS INTENDED FOR
HOUSEHOLD USE ONLY. Do not use this
appliance for anything other than its intended use.
Do not use outdoors.
10. DO NOT USE if the appliance is not working, has
been dropped, dropped into water, damaged or
left outdoors.
11. NO SERVICEABLE PARTS. Incorrect re-assembly
or repair can cause a risk of electrical shock or injury
to persons when the appliance is used. Contact
Customer Service or Service Center for the repair or
replacement under the warranty agreement.
12. Always use the appliance on a dry, level surface.
13. Keep hands, hair, clothing, as well as utensils
out of container while processing or blending
to reduce the risk of severe injury to persons or
damage to the appliance. A scraper may be used
but only when the appliance is not running.
14. Avoid contact with moving parts.
15. DO NOT attempt to sharpen blades.
16. DO NOT use the appliance if either set of blades
are bent or damaged.
17. To reduce the risk of injury, never assemble the
stacked blades in the pitcher or the chopping
blade in the bowl without the pitcher or the bowl
properly attached to the motor base.
18. DO NOT operate this appliance on or near any hot
surfaces (such as gas or electric burner or in a
heated oven).
19. The use of attachments or accessories
including canning jars, not recommended by the
manufacturer may result in fire, electric shock or
personal injury.
20. DO NOT remove any container from the motor
base while the appliance is in operation. Always
unplug the unit when not in use.
21. To reduce the risk of injury, NEVER operate the
appliance without the lid in place; DO NOT try to
defeat or bypass the interlock mechanism. When
using the removable blades, make sure they are
properly installed before operating the appliance.
22. DO NOT expose containers to extreme
temperature changes.
SAVE THESE
INSTRUCTIONS

3CUSTOMER CARE - NZ: 0800 002 999
THIS BOOK COVERS MODEL NUMBERS:
BL682NZ 30
TECHNICAL SPECIFICATIONS
Voltage: 220-240V~, 50/60Hz.
Power: 1500W
Pitcher Capacity: 2.1 L
Max Liquid: 2 L
Bowl Capacity: 1.8 L
Nutri Ninja™
Cup Capacity: 300 ml
500 ml
650 ml
900 ml
Euro-Pro and Ninja are registered trademarks of Euro-Pro
Operating LLC.
Sip & Seal,Nutri-Ninja, Total Crushing, Pro Extractor Blades
and Auto-iQ are trademarks of Euro-Pro Operating LLC. GMA-102233-EA-008

4CUSTOMER CARE - AU: 1800 890 840
Contents
Thank you for
purchasing the
Nutri Ninja™
|
Ninja®Blender
System with
AUTO-iQ™
Technology.
Getting to Know Your Nutri Ninja™| Ninja®Blender System with AUTO-iQ™Technology .............. 5
Using the Nutri Ninja™| Ninja®Blender System with AUTO-iQ™Technology ..............................7
Assembly and Use for the Blender ................................................................................... 8
Assembly and Use for the Food Processor .....................................................................10
Assembly and Use for the Disc Attachments ..................................................................12
Assembly and Use for the Mini Prep Bowl ......................................................................13
Assembly and Use for the Nutri Ninja™...........................................................................14
Programs, Speed Settings, & Uses for the Blender Pitcher ..............................................15
Programs, Speed Settings, & Uses for the Nutri Ninja™ Cups........................................... 15
Programs, Speed Settings, & Uses for the Food Processor..............................................16
Care & Maintenance ............................................................................................................... 17
Troubleshooting Guide.............................................................................................................18

5CUSTOMER CARE - NZ: 0800 002 999
h Silicone Grip Sleeve (x3)
iFood Processor Lid
jFood Processor Bowl
k Chopping Blade (food processor)
l Dough Blade (food processor)
mFeed Chute Lid
nMini Prep Bowl
oSlicing/Shredding Disc
(food processor)
aJumbo Multi Serve 900 ml Nutri
Ninja™Cup
bRegular 650 ml Nutri Ninja™Cup
cSmall 500 ml Nutri Ninja™Cup
dX-Small 300 ml Nutri Ninja™Cup
ePro Extractor Blades™
fSip & Seal™Lids (x3)
g Shaker Lid
pGrating Disc (food processor)
qSpindle for Discs & Mini Prep Bowl
r Mini Prep Bowl Blade
sBlender Pitcher
tBlender Lid with locking handle
u Stacked Blades (blender)
vMotor Base
NOTE: Blades are not interchangeable.
e
c
fh
j
i
s
t
v
u
k
l
a
b
d
p
nq
r
o
FROZEN DRINKS
SMOOTHIES
FOOD
PUREE
NutriNinja
NutriNinja
PULSE
HIGH
MED
ON
OFF
1500
WATTS
LOW
AUTO
AUTO
AUTO
A
UTO BLEND
A
UTO BLAST
FROZEN DRINKS
SMOOTHIES
FOOD
PUREE
NutriNinja
NutriNinja
PULSE
HIGH
MED
ON
OFF
1500
WATTS
LOW
AUTO
AUTO
AUTO
A
UTO BLEND
A
UTO BLAST
FROZEN DRINKS
SMOOTHIES
FOOD
PUREE
NutriNinja
NutriNinja
PULSE
HIGH
MED
ON
OFF
1500
WATTS
LOW
AUTO
AUTO
AUTO
A
UTO BLEND
A
UTO BLAST
NEW SHOOT LID
JUNE 9/14
HAS NEW BASE
NEW BOWL AND BLADE
JUNE 9/14
FROZEN DRINKS
SMOOTHIES
FOOD
PUREE
NutriNinja
NutriNinja
PULSE
HIGH
MED
ON
OFF
1500
WATTS
LOW
AUTO
AUTO
AUTO
A
UTO BLEND
A
UTO BLAST
FROZEN DRINKS
SMOOTHIES
FOOD
PUREE
NutriNinja
NutriNinja
PULSE
HIGH
MED
ON
OFF
1500
WATTS
LOW
AUTO
AUTO
AUTO
A
UTO BLEND
A
UTO BLAST
FROZEN DRINKS
SMOOTHIES
FOOD
PUREE
NutriNinja
NutriNinja
PULSE
HIGH
MED
ON
OFF
1500
WATTS
LOW
AUTO
AUTO
AUTO
A
UTO BLEND
A
UTO BLAST
NEW SHOOT LID
JUNE 9/14
HAS NEW BASE
NEW BOWL AND BLADE
JUNE 9/14
FROZEN DRINKS
SMOOTHIES
FOOD
PUREE
NutriNinja
NutriNinja
PULSE
HIGH
MED
ON
OFF
1500
WATTS
LOW
AUTO
AUTO
AUTO
A
UTO BLEND
A
UTO BLAST
FROZEN DRINKS
SMOOTHIES
FOOD
PUREE
NutriNinja
NutriNinja
PULSE
HIGH
MED
ON
OFF
1500
WATTS
LOW
AUTO
AUTO
AUTO
A
UTO BLEND
A
UTO BLAST
FROZEN DRINKS
SMOOTHIES
FOOD
PUREE
NutriNinja
NutriNinja
PULSE
HIGH
MED
ON
OFF
1500
WATTS
LOW
AUTO
AUTO
AUTO
A
UTO BLEND
A
UTO BLAST
NEW SHOOT LID
JUNE 9/14
HAS NEW BASE
NEW BOWL AND BLADE
JUNE 9/14
m
Getting To Know Your Nutri Ninja™
|
Ninja®Blender System with
Auto-iQ™Technology
g

6CUSTOMER CARE - AU: 1800 890 840
The Nutri Ninja™
|
Ninja®Blender System with Auto-iQ™Technology is a high powered innovative tool with a sleek design
and outstanding performance, a true asset to any kitchen. The Nutri Ninja™
|
Ninja®Blender System with Auto-iQ™
Technology features intelligent programs that combine pulsing, blending and pausing patterns that do the work for you!
Get great results every time with no guesswork required! For best results, be sure to carefully read all the instructions
contained in the manual before using this appliance.
Nutri Ninja®
|
Ninja®Blender System with Auto-iQ™Technology Features:
• PatentPendingNinja™Blade Technology
• BPAFreeBlenderPitcher,NutriNinja™Cups, Food Processor Bowl and Lids
• Drip-FreePourSpout
• TotalCrushing™Technology
• LEDControlPanelwithTimer
• Sturdy,Non-SlipBase
• SmartLidtechnologyforeasyrelease
• 3speeds:Low/Dough,Medium,&High
• 5Auto-iQ™settings - Auto-iQ™Frozen Drinks/Smoothies, Auto-iQ™Food Puree, Nutri Ninja™Auto-iQ™Blend,
Nutri Ninja™Auto-iQ™Ultra Blend and Auto-iQ™Pulse
• NutriNinja™Nutrient & Vitamin Extraction

7CUSTOMER CARE - NZ: 0800 002 999
PLEASE KEEP THESE IMPORTANT
SAFEGUARDS IN MIND WHEN USING THE
APPLIANCE:
WARNING: Never leave the appliance
unattended while in use.
CAUTION: DO NOT PROCESS HOT FOODS OR
HOT LIQUIDS.
CAUTION: Never remove the container while
the appliance is still running.
IMPORTANT: Never add ingredients into the
container before placing the blade in first.
IMPORTANT: Blades are not interchangeable.
IMPORTANT: DO NOT attempt to operate the
appliance without the lid on.
IMPORTANT: Never run the appliance empty.
CAUTION: Blades
are not locked
in place. If using
the pour spout,
ensure that the
lid is fully locked
onto the blender
pitcher.
CAUTION: Blades
are not locked in
place. If pouring
with the lid
removed, ALWAYS
remove the blade
assembly first
before pouring.
CAUTION: Blade assemblies are sharp, not locked
in place and removable, handle with care. When
handling the blade assemblies, always hold them
by the shaft.
BEFORE FIRST USE
1Remove all packaging material and labels from the
appliance.
2Wash the lids, blender pitcher, bowls, Nutri Ninja™cups
and blades in warm, soapy water with a soft cloth.
CAUTION: Handle the blade assemblies with care
when washing as the blades are very sharp.
3Rinse and dry thoroughly.
4The blender pitcher, bowls, Nutri Ninja™cups, lids and
blades, are all dishwasher safe. It is recommended that
the lids and blades be placed on the top rack. Ensure
that the blades are removed from the containers before
placing in the dishwasher.
5Wipe the motor base clean with a damp cloth.
Using the Nutri Ninja™
|
Ninja®Blender System with Auto-iQ™Technology

8CUSTOMER CARE - AU: 1800 890 840
Assembly and Use for the Blender
1Holding the Stacked Blade Assembly by the top of the
shaft, place it onto the drive gear inside the pitcher.
Ensure that the attachment is seated properly and is
standing upright. (Fig. 1)
NOTE: The blade will fit loosely on the drive gear.
2Place the motor base on a clean, dry, level surface such
as a counter or table top.
3 Align and lower the Pitcher onto the motor base.
(Fig. 2) Handle should be aligned slightly to the right
of the “LOCK” symbol on the motor base.
4Rotate the pitcher clockwise until it locks in place, you
will hear a click when the lock is engaged. (Fig. 3)
5The pitcher can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 4a, Fig. 4b)
6Add the ingredients to the pitcher, making sure that
they do not exceed the highest measured marking line
on the side of the pitcher.
NOTE: When blending any kind of liquids, such as
mixtures of any drinks or smoothies, do not exceed the
“MAX LIQUID” mark (2 L) on the pitcher.
NOTE: If you need to add additional ingredients while
the appliance is processing, open the pour spout cap
and pour the ingredients in through the opening.
7Holding the lid by the handle in the upright position, place
it on top of the pitcher aligning the triangle ( ) located
on the lid with the triangle ( ) located on the pitcher’s
handle. (Fig. 5a) Press the handle down until you hear
a click. The triangles on the lid and the blender handle
MUST be aligned in order for the blender to turn on.
(Fig. 5b)
8Plug the power cord into the electrical outlet and press
the power button ( ).
IMPORTANT: As a safety feature, the power light
( ) will flash and the motor will not work if the
pitcher and lid are not installed correctly. When
the pitcher and lid are installed properly, the
power light ( ) will be solid, indicating that the
appliance is ready for use.
ASSEMBLY
Fig. 2
Fig. 5a
Fig. 4a Fig. 4b
Fig. 1 Fig. 3
Fig. 5b
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
MED
LOW/
DOUGH
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
MED
LOW/
DOUGH
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
MED
LOW/
DOUGH
WARNING: Never leave the appliance unattended while in use.
CAUTION: Blade assemblies are sharp, not locked in place and removable, handle with care. When
handling the blade assemblies, always hold them by the shaft.
IMPORTANT: Make sure that the motor base is plugged in for use.

9CUSTOMER CARE - NZ: 0800 002 999
WARNING: Never leave the appliance unattended
while in use.
NOTE: Nutri Ninja™
|
Ninja®Blender System with
AUTO-iQ™Technology can sense which jar is on
the motor base. The function lights will illuminate
depending on which jar is placed on the motor base.
(Fig. 6)
9Press the power button to turn on the unit. Select
the speed or Auto-iQ™program that best suits your
needs. The Auto-iQ™program will stop the appliance
automatically at the end of the program. (Fig. 7)
NOTE: Pulse ingredients for even chopping by
holding the Auto-iQ™Pulse button until your desired
consistency is reached.
NOTE: Max PULSE iteration is 30 Pulses. After 30
Pulses allow 10 minutes to pass before running the
PULSE function up to an additional 30 Pulses.
10 To pause the appliance, press the selected speed or
Auto-iQ™Program a second time. (Fig. 8)
11 When you have reached your desired consistency, stop
the appliance by pressing the power button ( ) and
wait for the blade to stop turning. (Fig. 8)
12 Turn the pitcher anticlockwise to remove and then lift
off the base. (Fig. 9)
CAUTION: Never insert your hands in the pitcher
as the blades are sharp. Always use a spatula to
dislodge food that has stuck to the sides of the
pitcher.
CAUTION: If using the pour spout, ensure that the
lid is fully locked onto the blender pitcher.
CAUTION: If pouring with the lid removed, ALWAYS
remove the blade assembly first before pouring.
13 Depending on the consistency of the contents in the
container, open the pour spout cap and use the spout
to empty liquid contents.
14 For thicker consistencies, remove the lid and blade
attachment carefully (by its shaft), then empty contents
from the container. To remove the lid, press the release
button on the lid and pull the lid handle up to a 90°
angle and lift the lid off the blender pitcher. (Fig. 10)
15 Make sure that the unit is unplugged when not in use.
16 To release the motor base from the counter or table
top, place your hands underneath both sides of the
motor base and gently pull the unit up and towards you.
(Fig. 11)
Assembly and Use for the Blender - cont.
Fig. 8
USE REMOVAL
Fig. 6
Fig. 9
Fig. 7
Fig. 10
Fi g. 11

10CUSTOMER CARE - AU: 1800 890 840
Assembly and Use for the Processor Bowl
ASSEMBLY
MED
LOW/
DOUGH
Fig. 5a Fig. 5b
MED
LOW/
DOUGH
Fig. 2
MED
LOW/
DOUGH
Fig. 3Fig. 1
MED
LOW/
DOUGH
Fig. 4
Fig. 6a
Fig. 6b
NOTE: Nutri Ninja™
|
Ninja®Blender System with
Auto-iQ™Technology can sense which jar is on
the motor base. The function lights will illuminate
depending on which jar is placed on the motor base.
(Fig. 1)
1 Holding the desired blade by the top of the shaft, place
it onto the drive gear inside the bowl. Ensure that the
attachment is seated properly and is standing upright.
(Fig. 2)
NOTE: The blade will fit loosely on the drive gear.
2Place the motor base on a clean, dry, level surface such as a
counter or table top. Press down on the motor base to make
sure that the suction cups adhere to the counter or table top.
3 Align and lower the Processor Bowl onto the motor
base. (Fig. 3) Handle should be aligned slightly to the
right of the “LOCK” symbol on the motor base.
4Rotate the bowl clockwise until it locks in place, you will
hear a click when the lock is engaged. (Fig. 4)
5The bowl can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 5a, Fig. 5b)
6Add the ingredients to the bowl, making sure that they
do not exceed the “MAX” fill line on the side of the
bowl.
7Holding the lid by the handle in the upright position,
place it on top of the Processor Bowl aligning the
triangle ( ) located on the lid with the triangle ( )
located on the Processor Bowl handle. (Fig. 6a) Press
the handle down until you hear a click.
The triangles on the lid and the Processor Bowl handle
MUST be aligned in order for the blender to turn on.
(Fig. 6b)
NOTE: The 1.8 L bowl is not intended for blending
drinks. Do not overfill.
8 Plug the power cord into the electrical outlet and press
the power button ( ).
IMPORTANT: As a safety feature, the power button
() will flash and the motor will not work if the
bowl and lid are not installed correctly. When
the bowl and lid are installed properly, the power
button ( ) will be solid, indicating that the
appliance is ready for use.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Blade assemblies are sharp, not locked in place and removable, handle with care. When
handling the blade assemblies, always hold them by the shaft.
IMPORTANT: Make sure that the motor base is plugged in for use.

11 CUSTOMER CARE - NZ: 0800 002 999
Assembly and Use for the Processor Bowl - cont.
REMOVAL
Fig. 2 Fig. 3 Fig. 4
USE
Fig. 5
USE
Fig. 1
USING THE CHOPPING BLADE ASSEMBLY
1Holding the Chopping Blade assembly by the shaft,
place it onto the gear shaft inside the bowl. Ensure that
the attachment fits around the gear shaft and that it is
standing straight.
2 Add the ingredients and secure the bowl lid onto the
bowl. (Fig. 1)
3Plug the power cord into the electrical outlet and press
on the power button ( ). Select the speed or Auto-iQ™
program that best suits your needs. Pulse ingredients
for even chopping by holding the Auto-iQ™Pulse
button until your desired consistency is reached.
NOTE: Max PULSE iteration is 30 Pulses. After 30
Pulses allow 10 minutes to pass before running the
PULSE function up to an additional 30 Pulses.
NOTE: Please refer to “Speed Settings & Uses” chart
for suggested uses and speeds.
4When you have reached your desired consistency, stop
the appliance by pressing the power button ( ) and
wait for the blade to stop turning. (Fig. 2)
5To remove the lid, press the release button on the lid
and pull the lid handle up to a 90°angle. (Fig. 2)
6Turn the bowl anticlockwise and lift it to remove it from
the motor base. (Fig. 3)
CAUTION: If pouring from the bowl, ALWAYS
remove the blade assembly first before pouring.
7To release the motor base from the counter or table top,
place your hands underneath both sides of the motor
base and gently pull the unit up and towards you. (Fig. 4)
USING THE DOUGH BLADE
1Holding the dough blade by the shaft, place it onto the
gear shaft inside the bowl. Ensure that the attachment
fits around the gear shaft and that it is standing straight.
(Fig. 5)
2Add the ingredients and secure the bowl lid onto the bowl.
3Plug the power cord into the electrical outlet and press
on the power button ( ). Select LOW/DOUGH on the
control panel and process until ingredients come
together to form a mass.
NOTE: Please refer to “Speed Settings & Uses” chart
for suggested uses and speeds.
4Once finished making dough, stop the appliance by
pressing the power button ( ) and wait for the blade to
stop turning.
5To remove the lid, press the release button on the lid
and pull the lid handle up to a 90°angle. (Fig. 2)
6Turn the bowl anticlockwise and lift it to remove it from
the motor base. (Fig. 3)
7To release the motor base from the counter or table top,
place your hands underneath both sides of the motor
base and gently pull the unit up and towards you.
(Fig. 4)
WARNING: Never leave the appliance unattended while in use.
CAUTION: Use caution when handling the blade assemblies as the blades are very sharp.

12CUSTOMER CARE - AU: 1800 890 840
Fig. 5
Assembly and Use for the Disc Attachments
USING THE DISCS
NOTE: Disc attachments must be used with the
feed chute lid.
1Place the motor base on a clean, dry, level surface such
as a counter or table top. (Fig. 5)
2Secure the bowl onto the motor base.
3Place the spindle inside the bowl.
4Use the finger holes to grasp the selected disc and
place it over the spindle.
5Place the feed chute lid on the bowl and turn clockwise
until you hear a click indicating the lid is locked in
place. (Fig. 5)
6Plug the power cord into the electrical outlet and press
up on the power toggle ( ) to turn the power “On”.
7Select HIGH on the control panel. The discs will begin
spinning.
8Add the food that you want to slice, shred or grate
through the feed chute on the lid. (Fig. 5) Use the
two-part food pusher to help guide the food through
the feed chute. The middle piece of the food pusher is
removable to use for smaller ingredients.
9When finished,stop the appliance by pressing the power
button ( ) and wait for the disc to stop turning. Press the
button on the feed chute lid located near the handle to
unlock and turn the lid anticlockwise. Lift to remove from
the processor bowl. Using the finger holes, carefully lift
the disc out of the bowl and remove the spindle.
10 To release the motor base from the counter or table top,
place your hands underneath both sides of the motor
base and gently pull the unit up and towards you.
CAUTION: Use caution when handling the blade assemblies as the blades are very sharp.
IMPORTANT: Use only the High setting when using either disc.

13 CUSTOMER CARE - NZ: 0800 002 999
ASSEMBLY
Assembly and Use for the Mini Prep Bowl
USE
USING THE MINI PREP BOWL
NOTE: The mini prep bowl must be used with the
flat food processor lid.
1Place the 1.8 L bowl onto the motor base.
2Holding the spindle by the shaft, place it onto the gear
shaft inside the 1.8 L bowl. Ensure that the attachment
fits around the gear shaft and that it is standing
straight. (Fig. 1)
3Place the mini prep bowl aligning the spindle inside the
centre post. (Fig. 2)
4Hold the prep bowl blade by the shaft and carefully place
it over the centre post of the mini prep bowl. (Fig. 3)
5Add ingredients into the mini prep bowl.
6Holding the lid by the handle in the upright position,
place it on top of the 1.8 L bowl aligning the arrow ( )
located on the lid with the arrow ( ) located on the
bowl’s handle. (Fig. 4) Press the handle down until you
hear a click.
Fig. 1 Fig. 2
Fig. 3
Fig. 5
FROZEN DRINKS
SMOOTHIES
FOOD
PUREE
NutriNinja
NutriNinja
PULSE
HIGH
MED
ON
OFF
1500
WATTS
LOW
AUTO
AUTO
AUTO
A
UTO BLEND
A
UTO BLAST
REMOVAL
Fig. 6
FROZEN DRINKS
SMOOTHIES
FOOD
PUREE
NutriNinja
NutriNinja
PULSE
HIGH
MED
ON
OFF
1500
WATTS
LOW
AUTO
AUTO
AUTO
A
UTO BLEND
A
UTO BLAST
Fig. 7
7Plug the power cord into the electrical outlet and press
on the power button ( ).
8Select the speed that best suits your needs. For best
results, hold the Auto-iQ™Pulse button down until you
have reached your desired consistency. (Fig. 5)
NOTE: Max PULSE iteration is 30 Pulses. After 30
Pulses allow 10 minutes to pass before running the
PULSE function up to an additional 30 Pulses.
NOTE: Please refer to “Speed Settings & Uses” chart
for suggested uses and speeds.
9When you have reached your desired consistency, stop
the appliance by pressing the power button
( ) and wait for the blade to stop turning.
10 To remove the lid, pull the lid handle up to a 90° angle
and lift the lid off. (Fig. 6)
11 Carefully hold the mini prep bowl blade by the shaft and
lift it out of the mini prep bowl. (Fig. 7)
12 Turn the bowl anticlockwise and then lift off the base.
CAUTION: If pouring from the bowl, ALWAYS
remove the blade assembly first before pouring.
Fig. 4
WARNING: Never leave the appliance unattended while in use.
CAUTION: Use caution when handling the blade assemblies as the blades are very sharp.

14CUSTOMER CARE - AU: 1800 890 840
6. To pause the appliance, press the selected speed or
Auto-iQ™Program a second time.
7Once you have reached your desired consistency,
turn the power button off. Turn the Nutri Ninja™cup
anticlockwise and pull straight up to remove.
(Fig. 5, Fig. 6)
NOTE: Do not overfill! To avoid spilling, do not add
ingredients past the “MAX” fill line.
8Turn the cup upright and remove the Pro Extractor
Blades™by twisting the blade assembly anticlockwise.
9Place the Sip & Seal™lid onto the Nutri Ninja™cup, twist
to seal and enjoy!
10 Make sure that the motor base is unplugged when not in
use.
11 To release the motor base
from the counter or table top,
place your hands underneath
both sides of the motor base
and gently pull the unit up and
towards you. (Fig. 7)
Assembly and Use for the Nutri Ninja™
Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6
Fig. 7
Fig. 1
NOTE: Nutri Ninja™
|
Ninja®Blender System with Auto-iQ™
Technology can sense which jar is on the motor base. The
function lights will illuminate depending on which jar is placed
on the motor base. (Fig. 1)
1Place the motor base on a clean, dry, level surface such
as a counter or table top. Press down on the motor base
to make sure that the suction cups adhere to the counter
or table top.
2Add ingredients to the Nutri Ninja™cup.
3Place the Pro Extractor Blades™onto the cup and tightly
screw it on clockwise until you have a good seal. (Fig. 2)
4Turn the Nutri Ninja™cup upside down and place it onto
the motor base, aligning the tabs on the cup with the
motor base. Rotate the Nutri Ninja™cup clockwise until
it locks in place, you will hear a click when the lock is
engaged. (Fig. 3)
5Press the power button on, and select the speed or Auto-
iQ™program that suits your needs. The
Auto-iQ™program will stop the appliance automatically
at the end of the program. (Fig. 4)
ASSEMBLY USE REMOVAL
WARNING: Never leave the appliance unattended while in use.
CAUTION: Use caution when handling the blade assemblies as the blades are very sharp.
IMPORTANT: Make sure that the motor base is plugged in for use.

15 CUSTOMER CARE - NZ: 0800 002 999
Speed Setting & Uses for the Blender
Speed Setting & Uses for the Nutri Ninja™Cup
FUNCTION CONTAINER BLADE
TYPE
SPEED or
PROGRAM TYPE OF FOOD
Smoothies Nutri Ninja®Cup Pro Extractor
Blades™
Nutri Ninja®Auto-iQ™
Blend
Smoothies
Frappes
Milkshakes
Protein Drinks
Green Smoothies Nutri Ninja®Cup Pro Extractor
Blades™
Nutri Ninja®Auto-iQ™
Ultra Blend
Frozen Fruits
Frozen Vegetables
Kale
Celery
Spinach
Seeds
Ice
Grating Nutri Ninja®Cup Pro Extractor
Blades™
AUTO-iQ™Pulse
Nutri Ninja™AUTO-iQ™
Blend
High
Grated Cheese
Bread Crumbs
Spices
Chopping Nutri Ninja®Cup Pro Extractor
Blades™
AUTO-iQ™Pulse
Nutri Ninja™AUTO-iQ™
Blend
High
Salsa
Vegetables
Nuts
FUNCTION CONTAINER BLADE
TYPE
SPEED or
PROGRAM TYPE OF FOOD
Frozen Drinks /
Ice Crush Blender Pitcher Stacked Blade Auto-iQ™Frozen Drinks/ Smoothies
Ice
Frozen Drinks
Smoothies
Pureeing Blender Pitcher Stacked Blade Auto-iQ™Food Puree
Smoothies
Soups
Milkshakes

16CUSTOMER CARE - AU: 1800 890 840
Speed Setting & Uses for the Food Processor
FUNCTION CONTAINER BLADE
TYPE
SPEED or
PROGRAM TYPE OF FOOD
Mincing Food Processor
Bowl
Chopping
Blade Auto-iQ™Pulse
Onion
Garlic
Herbs
Kneading and
Dough Mixing
Food Processor
Bowl Dough Blade Low/Dough
Bread Dough
Pie Dough
Pizza Dough
Pretzel Dough
Cookie Dough
Processing Food Processor
Bowl
Chopping
Blade
Auto-iQ™Food Puree
Low/Dough
Medium
High
Pâtés
Stewed Fruits
Dips
Apple Sauce
Spreads
Baby Food
Emulsifying Food Processor
Bowl
Chopping
Blade
Low/Dough
Medium
Salad Dressings
Dips
Sauces
Grinding Food Processor
Bowl
Chopping
Blade Medium Meat
Grating Food Processor
Bowl
Chopping
Blade
Grating Disc
Auto-iQ™Pulse
Low/Dough (when using
Disc)
Grated Cheese
Bread Crumbs
Spices
Chopping Food Processor
Bowl
Chopping
Blade Auto-iQ™Pulse
Salsa
Vegetables
Nuts
Batters Food Processor
Bowl Dough Blade Low/Dough Cake Mixes Batters
Slicing/
Shredding
Food Processor
Bowl
Reversible
Slicing
Shredding
Disc
Low/Dough Vegetables
Cheese

17 CUSTOMER CARE - NZ: 0800 002 999
HOW TO CLEAN
CAUTION: Make sure that the motor base is
unplugged from the power source before inserting
or removing any attachment and before cleaning.
CAUTION: DO NOT immerse the motor base into
water or any other liquid.
CAUTION: Use caution when handling the blade
assemblies as the blades are very sharp.
1Separate/remove all parts from each other.
2 Clean the motor base with a damp cloth and wipe dry.
3Place the pitcher, Nutri Ninja™cup and bowl in the
dishwasher. Place the lids and attachments on the top rack.
NOTE: You may also wash the containers by filling ¾ of
the container with warm water and a drop of dish washing
detergent, placing the corresponding lid on the container
and pressing the pulse button a few times. Once clean,
remove the container from the motor base. Rinse the
container, attachment and lid under running water. Allow
all the parts to dry before storing.
If the appliance needs servicing, please call customer
care at 0800 002 999 or 1800 890 840.
Care & Maintenance
HOW TO STORE
1 Store the Nutri Ninja™| Ninja®Blender System with
AUTO-iQ™Technology
upright with the pitcher on the
motor base, stacked blade inside the pitcher and lid on
the pitcher. Do not place anything on top. Store the Food
Processor Bowl with the chopping blade inside and the lid
on top. S tore the Nutri Ninja™cup and the rest of the
attachments along side the appliance or in a cabinet
where they will not be damaged and won’t cause a
hazard.
RESETTING THE MOTOR THERMOSTAT
The Nutri Ninja™| Ninja®Blender System with AUTO-iQ™
Technology
features a safety system which prevents
damage to the unit’s motor and drive system should you
inadvertently overload your appliance. If the appliance
is being overloaded, the motor will stop. Allow
the appliance to cool for approximately 15
minutes. To reset the appliance, follow the resetting
procedure below:
1 Unplug the appliance from the electrical outlet.
2 Remove and empty the container and ensure that no
food is jamming the cutting blades or attachments.
3 Allow the appliance to cool for approximately 15
minutes.
4 Re-install the container onto the base and re-plug the
appliance into the electrical outlet.
5 Proceed to use the appliance as before making sure not
to exceed the recommended maximum capacities.
Pizza Dough
Ingredients:
1/3 tsp Salt
1/4 oz. Packet Active Dry Yeast
1/2 tsp Sugar
2/3 cup Warm Water (105° - 110°F)
2 cups All-purpose Flour
1/4 cup Olive Oil
Reserved Flour
Reserved Water
Directions:
1. Combine the yeast, sugar, and warm water in a small bowl and set aside until foamy, about 5 minutes.
2. Place the dough blade into the Food Processor Bowl and add the flour, salt, olive oil, and the yeast mixture. Turn
unit ON and select “LOW/DOUGH”. Process until all of the ingredients come together to form a mass. Remove
the dough and divide in half, kneading the two balls of dough for 1-2 minutes. Place one ball into a lightly oiled
bowl and cover loosely with plastic wrap, allowing to rest and rise for 1 hour. Freeze the other dough ball for up
to two months.
Tip: If the dough is too wet, add a tablespoon of flour. If the dough is too dry, add a tablespoon of water.
Suggested Recipe

18CUSTOMER CARE - AU: 1800 890 840
Troubleshooting Guide
PROBLEMS POSSIBLE REASONS & SOLUTIONS
Motor Doesn’t Start or
Attachment Doesn’t Rotate.
Make sure the container is securely locked on the motor base.
Make sure the lid is securely on container in the correct position (align
arrows).
The appliance is turned “Off”. Press the power button ( ) to turn “On”.
Check that the plug is securely inserted into the electrical outlet.
Check the fuse or circuit breaker.
The unit has overloaded. The appliance will stop and the power light will
flash. Unplug and wait approximately 15 minutes before using again.
The unit has overheated. Unplug and wait approximately 15 minutes before
using again.
Check to make sure the unit is not overloaded.
Food is Unevenly Chopped.
Either you are chopping too much food at one time, or the pieces are not of
even size and processing smaller amounts per batch.
Food is Chopped Too Fine or is
Too Watery.
The food has been over processed. Use Auto-iQ™Pulse button for
controlled processing.
Food Collects On Lid or On the
Sides of the Container.
The mixture is too thick. Add more liquid.
You Cannot Achieve Snow
From Solid Ice.
Do not use ice that has been sitting out or has started to melt. Use ice
straight from the freezer.
Start with a few pulses and then go to a continuous blending cycle.
Motor Base Won’t Stick to
Counter or Table Top.
Make sure surface and suction feet are wiped clean. Suction feet will only
stick to smooth surfaces. Suction feet WILL NOT stick on some surfaces
such as, wood, tile and non-polished finishes.
DO NOT attempt to use appliance when the motor base is stuck to a
surface that is not secure, (cutting board, platter, plates, etc.).
You get an “Err” Message.
Your Ninja®is able to detect which jar is on the base. You may be trying
to use a program that is not designed for the jar you have installed. The
programs will light up indicating which programs are available for each jar.
You have a blinking red light.
The unit is not installed properly. For your safety the unit will only be able to
be turned on when it is properly assembled. Please refer to the assembly
pages of this inspiration guide for assistance.

19 CUSTOMER CARE - NZ: 0800 002 999
Notes