Ninja BL770NZ User manual

Mega Kitchen System
OWNER’S GUIDE
BL770NZ
®

1AUST: 1800 890 840 NZ: 0800 002 999
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING ELECTRICAL APPLIANCES, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING YOUR
NINJA®PROFESSIONAL BLENDER.
IMPORTANT: This appliance is not intended for use
by persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
Children shall not use or play with this appliance. Close
supervision is necessary to keep appliance and cord
out of reach of children during use.
WARNING:The blades are not affixed to the unit.
They are removable and very sharp. Handle
withcare!
CAUTION: ln order to avoid a hazard due to
inadvertent resetting of the thermal cut-out, this
appliance must not be supplied through an
external switching device, such as a timer, or
connected to a circuit that is regularly switched
on and off by the utility.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
OR INJURY:
1. To protect against electrical shock, do not
submerge the appliance or allow the power
cord to come into contact with water or any
otherliquid.
2. DO NOT allow young children to operate the
appliance or use as a toy. Close supervision
is necessary when any appliance is used
nearchildren.
3. Never leave an appliance unattended when in use.
4. Turn the appliance off and remove the power cord
from the electrical outlet when not in use, before
assembling or disassembling parts, accessing
parts that move while in use and before cleaning.
To unplug, grasp the plug and pull from the
electrical outlet. Never pull from the power cord.
5. DO NOT abuse the power cord. Never carry
the appliance by the power cord or yank it to
disconnect from electrical outlet; instead, grasp
the plug and pull to disconnect.
6. DO NOT use with damaged cord or plug. Contact
Customer Services or Service Center for the
repair or replacement of the line cord.
7. DO NOT USE if the appliance is not working, has
been dropped, dropped into water, damaged or
left outdoors.
8. NO SERVICEABLE PARTS. Incorrect re-
assembly or repair can cause a risk of electrical
shock or injury to persons when the appliance
is used. Contact Customer Service or Service
Center for the repair or replacement under the
warranty agreement
9. Always use the appliance on a dry, level surface.

2
AUST: 1800 890 840 NZ: 0800 002 999
22. DO NOT expose containers to extreme
temperature changes.
23. CAUTION: DO NOT process hot foods or
hot liquids. Allow hot ingredients to cool
beforeprocessing.
24. DO NOT overfill. DO NOT exceed max fill line.
25. DO NOT operate the appliance empty.
26. To reduce the risk of burns, always allow the
appliance to cool before taking off parts and
before cleaning.
27. Max ON time is 30 seconds under 1500W load.
If the appliance overheats, a thermal switch will
become activated and shut off the motor. To
reset, unplug the appliance and let it cool down
for approximately 15 minutes before using again.
28. In the event that the unit overloads, the control
panel lights will flash and the unit will shut down.
Unplug the unit and wait 15 minutes to reset.
29. The maximum rating is based on without the top
blades inserted into the pitcher. This drives the
greatest power. Other recommended attachments
may draw significantly less power or current.
30. To avoid injury, never attempt to place the single
serve blade assembly onto the motor base
without first assembling the blade assembly to the
single serve cup.
31. DO NOT push food into the food chute with your
fingers. Always use the food pusher provided.
32. THIS PRODUCT IS INTENDED FOR
HOUSEHOLD USE ONLY. Do not use this
appliance for anything other than its intended use.
Do not use outdoors.
WARNING: Extension cords are not
recommended for use with this product.
10. Keep hands, hair, clothing, as well as utensils
out of container while processing or blending
to reduce the risk of severe injury to persons or
damage to the appliance. A scraper may be used
but only when the appliance is not running.
11. CAUTION: The blades are not affixed to the unit.
They are removeable and extremely sharp. When
handling the top blades or the chopping
blades, do not hold the blades but rather
always hold by the shaft. Blades are sharp.
Handle carefully!
12. Avoid contact with moving parts.
13. DO NOT attempt to sharpen blades.
14. DO NOT use the appliance if either set of blades
are bent or damaged.
15. To reduce the risk of injury, never assemble the
top blades in the pitcher or the chopping blade in
the bowl without the pitcher or the bowl properly
attached to the motor base.
16. DO NOT operate this appliance on or near any hot
surfaces (such as gas or electric burner or in a
heated oven).
17. The use of attachments or accessories
including canning jars, not recommended by the
manufacturer may result in fire, electric shock or
personal injury.
18. DO NOT remove any container from the motor
base while the appliance is in operation. Always
unplug the unit when not in use.
19. To reduce the risk of injury, NEVER operate the
appliance without the lid in place; DO NOT try to
defeat or bypass the interlock mechanism. When
using the removable blades, make sure they are
properly installed before operating the appliance.
20. CAUTION: DO NOT BLEND HOT LIQUIDS.
21. Extreme caution must be used when moving
an appliance containing hot food, water or
otherliquids.
SAVE THESE
INSTRUCTIONS

3AUST: 1800 890 840 NZ: 0800 002 999
THIS BOOK COVERS MODEL NUMBERS:
BL770NZ 30
TECHNICAL SPECIFICATIONS
Voltage: 220-240V., 50/60Hz.
Power: 1500 Watts
Max ON time is 30 seconds under 1500W load
Pitcher Capacity: 2.1 L
Bowl Capacity: 1.8 L
Single Serve Capacity: 470 ml
Z854
SA A130957E A

4
AUST: 1800 890 840 NZ: 0800 002 999
Contents
Thank you for
purchasing the
Ninja®Mega
Kitchen System.
Getting to Know Your Ninja® Mega Kitchen System......................................................5
Using the Ninja®Mega Kitchen System .....................................................................7
Assembly and Use for the 2.1 L Pitcher......................................................................8
Assembly and Use for the Single Serve Cup..............................................................10
Assembly and Use for the 1.8 L Bowl .......................................................................11
Speed Setting & Uses..............................................................................................13
Care & Maintenance ...............................................................................................14
Troubleshooting Guide.............................................................................................15
Warranty ................................................................................................................18

5AUST: 1800 890 840 NZ: 0800 002 999
Getting To Know Your Ninja®Mega Kitchen System
dFood Processor Bowl
eFood Processor Lid
fDough Blade (bowl)
gChopping Blade (bowl)
aTo-Go Single Serve Cup (x 2)
bSingle Serve Blade
cTo-Go Single Serve Lids (x 2)
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
HIGH PULSE
LOW DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE FROZEN
BLENDING
a
d
h
k
i j
e f g
b c
hBlender Pitcher
iLid with Locking Handle (pitcher)
j Stacked Blades (Removable) (pitcher)
k Motor Base
NOTE: Attachments are not
interchangeable.

6
AUST: 1800 890 840 NZ: 0800 002 999
The Ninja®Mega Kitchen System is a professional, high powered innovative tool with a sleek design and outstanding
performance, a true asset to any kitchen. It is perfect for ice crushing, blending, food mixing, and complete juicing. The
Ninja®Mega Kitchen System also features a unique capability to knead dough for pizzas, breads, pretzels and cookies!
Create all of your favourite recipes fast and easy with just one touch of a button. For best results, be sure to carefully
read all the instructions contained in the manual before using this appliance.
FEATURES:
• PatentedPitcher-BPAFree
• 1.8LBowlwithDrizzleHole-BPAFree
• SingleServeDrinkCup-BPAFree
• Lock–InLid,FeaturingPourSpout
• EasytoCleanElectronicControlPanel
• Sturdy,Non-SlipBase
• HiddenDrainHoles-preventwaterbuildupfromdishwasher

7AUST: 1800 890 840 NZ: 0800 002 999
PLEASE KEEP THESE IMPORTANT
SAFEGUARDS IN MIND WHEN USING THE
APPLIANCE:
IMPORTANT: Never add ingredients into the
container before placing the attachment in first.
IMPORTANT: Attachments are not
interchangeable.
CAUTION: Blades are sharp! Use extreme caution
when handling the blade assemblies. Always hold
them by the shaft.
IMPORTANT: DO NOT attempt to operate the
appliance without the lid on.
IMPORTANT: Never run the appliance empty.
CAUTION: DO NOT BLEND HOT LIQUIDS.
WARNING: Secure the appliance while in use by
pressing down on the lid with one hand.
CAUTION: Never remove the container while the
appliance is still running.
WARNING: Never leave the appliance unattended
while in use.
BEFORE FIRST USE
1Remove all packaging material and labels from
theappliance.
2Wash the lids, pitcher, bowl, single serve cups and
attachments in warm, soapy water with a soft cloth.
Use caution when washing the blade assemblies
as the blades are very sharp.
3Rinse and dry thoroughly.
4The pitcher, bowl, single serve cups, lids and
attachments, are all dishwasher safe. It is recommended
that the lids and attachments be placed on the top rack.
Ensure that the attachments are removed from the
containers before placing in the dishwasher.
5Wipe the motor base clean with a damp cloth.
Using the Ninja®Mega Kitchen System

8
AUST: 1800 890 840 NZ: 0800 002 999
Fig. 3b
Fig. 2
Fig. 1
Assembly and Use for the 2.1 L Pitcher
IMPORTANT: Make sure that the motor base is
plugged in for use.
1Place the motor base on a clean, dry, level surface such
as a counter or table top.
2Align and lower the Pitcher onto the motor base. (Fig. 1)
Handle should be aligned slightly to the right of the
“LOCK” symbol on the motor base.
3Rotate the pitcher clockwise as far as it will go to lock
in place. (Fig. 2)
4The pitcher can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 3a, Fig. 3b)
5 Holding the 6-Blade Assembly by the top of the shaft,
place it onto the drive gear inside the pitcher. Ensure
that the attachment is seated properly and is standing
upright. (Fig. 4)
NOTE: The blade will fit loosely on the drive gear.
6Add the ingredients to the pitcher, making sure not to
overfill.
NOTE: Do not exceed the highest measured marking
line on the side of the pitcher.
NOTE: If you need to add additional ingredients while
the appliance is blending, open the pour spout cap and
pour the ingredients in through the opening.
7Plug the power cord into the electrical outlet and press
the power button ( ).
NOTE: As a safety feature, the power
button ( ) will flash and the motor will not work
if the pitcher and lid are not installed correctly.
When the pitcher and lid are installed properly,
the power button ( ) will be solid, indicating that
the appliance is ready for use.
8Holding the lid by the handle in the upright position, place
it on top of the pitcher aligning the arrow ( ) located on
the lid with the arrow ( ) located on the pitcher’s handle.
(Fig. 5) Press the handle down until you hear a click.
Fig. 4
Fig. 5
Assembly
Fig. 3a

9AUST: 1800 890 840 NZ: 0800 002 999
9Select the speed that best suits your needs. (Fig. 6)
NOTE: Pulse ingredients for even blending by pressing
down in short intervals.
10 When you have reached your desired consistency, stop
the appliance by pressing the power button ( ) and
wait for the attachment to stop turning. (Fig. 7)
11 To remove the lid, press the release button on the lid,
pull the lid handle up to a 90° angle and lift the lid off.
Turn the pitcher counter clockwise and then lift off the
base. (Fig. 7, Fig. 8)
Assembly and Use for the 2.1 L Pitcher - cont.
Fig. 7
USE REMOVAL
Fig. 6 Fig. 8
CAUTION: Never insert your hands in the pitcher as the
blades are sharp. Always use a spatula to dislodge food
that has stuck to the sides of the pitcher.
12 Depending on the consistency of the contents in the
container, open the pour spout cap and use the spout
to empty liquid contents. For thicker consistencies,
remove the lid and attachment carefully (by its shaft),
then empty contents from the container.
13 Make sure that the unit is unplugged when not in use.

10
AUST: 1800 890 840 NZ: 0800 002 999
IMPORTANT: Make sure that the motor base is
plugged in for use.
1 Place the motor base on a clean, dry, level surface such
as a counter or table top.
2Add ingredients to the single serve cup.
3Place the single serve blade onto the cup and screw it
tightly until you have a good seal. (Fig. 1)
4Turn the single serve cup upside down and place it onto
the motor base, aligning the tabs on the cup with the motor
base. Turn the single serve cup clockwise. (Fig. 2) Turn
the power button on, the single serve button will illuminate.
5Press down on the Single Serve button in short
intervals to activate. (Fig. 3)
Fig. 1 Fig. 2
Assembly and Use for the Single Serve Cup
Fig. 3 Fig. 4 Fig. 5
ASSEMBLY USE REMOVAL
6Once you have reached your desired consistency, turn
the power button off. Turn the single serve cup counter
clockwise and pull straight up to remove. (Fig. 4, Fig. 5)
NOTE: Do not overfill! To avoid spilling, do not add
ingredients past the “Max” fill line.
7Turn the cup upright and remove the single serve blade
by twisting the blade assembly clockwise.
8Place the To-Go drinking lid onto the single serve drink
cup, twist to seal and enjoy!
9Make sure that the motor base is unplugged when not
in use.
For best results, use short “PULSES”... Practice makes perfect!!

11 AUST: 1800 890 840 NZ: 0800 002 999
Fig. 1
Fig. 2
Assembly and Use for the 1.8L Bowl
ASSEMBLY
Fig. 3a
Fig. 3b
IMPORTANT: Make sure that the motor base is
plugged in foruse.
1Place the motor base on a clean, dry, level surface such
as a counter or table top.
2Align and lower the Bowl onto the motor base. (Fig.
1) Handle should be aligned slightly to the right of the
“LOCK” symbol on the motor base.
3Rotate the bowl clockwise as far as it will go to lock in
place. (Fig. 2)
4The bowl can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 3a, Fig. 3b)
5Holding the desired blade by the top of the shaft, place
it onto the drive gear inside the bowl. Ensure that the
attachment is seated properly and is standing upright.
(Fig. 4)
NOTE: The blade will fit loosely on the drive gear.
6Add the ingredients to the bowl, making sure that they
do not exceed the highest measured marking line on
the side of thebowl.
7Plug the power cord into the electrical outlet and press
the power button ( ).
NOTE: As a safety feature, the power button ( )
will flash and the motor will not work if the bowl
and lid are not installed correctly. When the bowl
and lid are installed properly, the power button (
) will be solid, indicating that the appliance is
ready for use.
8Holding the lid by the handle in the upright position,
place it on top of the bowl aligning the arrow
( ) located on the lid with the arrow ( ) located on the
bowl’s handle. (Fig. 5) Press the handle down until you
hear a click.
NOTE: The 1.8L bowl is not intended for blending
drinks. Do not overfill.
NOTE: To add liquids during blending, open the drizzle
hole on the top of the lid and pour
the liquid slowly into the mixture.
NOTE: Do not exceed the highest
measured marking line on the
side of the bowl. For meats do not
exceed 1 L bowl mark.
Fig. 4
Fig. 5

12
AUST: 1800 890 840 NZ: 0800 002 999
USING THE 4-BLADE ASSEMBLY
1Holding the 4-Blade assembly by the shaft, place it
onto the gear shaft inside the bowl. Ensure that the
attachment fits around the gear shaft and that it is
standing straight.
2Add the ingredients and secure the bowl lid onto the
bowl. (Fig. 1)
3Plug the power cord into the electrical outlet and press
on the power button ( ).
4Select the speed that best suits your needs. Pulse
ingredients evenly by pressing down in short intervals.
NOTE: Please refer to “Speed Settings & Uses” chart
for suggested uses and speeds.
5When you have reached your desired consistency, stop
the appliance by pressing the power button ( ) and
wait for the blade to stop turning.
6To remove the lid, pull the lid handle up to a 90° angle
and lift the lid off. Turn the bowl counter clockwise and
then lift off the base. (Fig. 2, Fig. 3)
NOTE: Do not exceed the highest measured marking.
For meats, do not exceed 1 L marking.
USE
USING THE DOUGH BLADE
IMPORTANT: Use only the “DOUGH” button when
using this attachment.
IMPORTANT: Use the suction lever when using the
dough blade on SPEED 1/DOUGH.
1Place the motor base on a clean, dry, level surface such
as a counter or table top. (Fig. 4) Push the suction
lever on the side of the motor base down to secure the
suction feet to the surface. (Fig. 4a) If the suction feet
have not totally adhered to the surface, press down
lightly on the base to give the suction feet a better grip.
2Secure the bowl onto the motor base.
3Holding the dough blade by the shaft, place it onto the
gear shaft inside the bowl. Ensure that the attachment
fits around the gear shaft and that it is standing straight.
4Add the ingredients and secure the bowl lid onto the bowl.
NOTE: For best results add wet ingredients first and
then add dry ingredients.
5Plug the power cord into the electrical outlet and press
on the power button ( ).
6Once finished making dough, remove the bowl from the
motor base. (Fig. 2, Fig. 3)
7To release the motor base from the counter or table
top, pull the suction lever up to release the suction feet.
(Fig. 4b)
NOTE: The suction lever activates the suction feet for
added stability.
Fig. 1
Suction
Lever
Fig. 4
Activate
Suction
Release
Suction
Fig. 4a
Fig. 4b
Fig. 2
Fig. 3
REMOVAL USE

13 AUST: 1800 890 840 NZ: 0800 002 999
Speed Setting & Uses
IMPORTANT: Use the suction lever when using the dough blade on SPEED 1/DOUGH.
FUNCTION CONTAINER ATTACHMENT SPEED
BUTTON TYPE OF FOOD
Single Serve
Blending Single Serve Cup Single Serve Blade Single Serve
Smoothies
Frappes
Milk Shakes
Mincing Single Serve Cup Single Serve Blade Single Serve
Onion
Garlic
Herbs
Kneading Bowl Dough Blade 1
Bread dough
Pie dough
Pizza dough
Pretzel dough
Dough Mixing Bowl Dough Blade 1Cookie dough
Blending Pitcher/Bowl
Single Serve Cup
Blade Assembly
Single Serve Blade
2
Pulse
Single Serve
Pâtés
Stewed fruits
Dips
Apple sauce
Spreads
Soups
Baby food
Emulsifying Bowl Blade Assembly 2
Salad Dressings
Dips
Sauces
Grinding Bowl Blade Assembly 2Meat
Grating Bowl
Single Serve Cup
Blade Assembly
Single Serve Blade
3 or Pulse
Single Serve
Grated cheese
Bread crumbs
Spices
Fine Blending
Bowl
Single Serve Cup
Pitcher
Blade Assembly
Single Serve Blade
Pulse
Single Serve
3
Salsa
Vegetables
Nuts
Mixing Bowl Dough Blade 1Light cake mixes
Batters
Ice Crushing Pitcher
Single Serve Cup
Blade Assembly
Single Serve Blade
3
Single Serve Ice
Pureeing Pitcher
Single Serve Cup
Blade Assembly
Single Serve Blade
3
Single Serve
Smoothies
Smooth soups
Milkshakes

14
AUST: 1800 890 840 NZ: 0800 002 999
Care & Maintenance
HOW TO CLEAN
CAUTION: Make sure that the motor base is unplugged
from the power source before inserting or removing any
attachment and before cleaning.
CAUTION: DO NOT immerse the motor base into water
or any other liquid.
1Separate/remove all parts from each other.
2Clean the motor base with a damp cloth and wipe dry.
3Place the pitcher, single serve cup and bowl in the
dishwasher. Place the lids and attachments on the
top rack. Use caution when handling the blade
assemblies as the blades are very sharp.
NOTE: You may also wash the containers by filling ¾
of the container with warm water and a drop of dish
washing detergent, placing the corresponding lid on the
container and pressing the pulse button a few times.
Once clean, remove the container from the motor base.
Rinse the container, attachment and lid under running
water. Allow all the parts to dry before storing.
HOW TO STORE
1Store the Ninja®Mega Kitchen System upright with the
pitcher on the motor base, 6-Blade assembly inside the
pitcher and lid on the pitcher. Do not place anything on
top. Store the bowl with the 4-Blade assembly inside
and the lid on top. Store the single serve cup and the
rest of the attachments along side the appliance or in
a cabinet where they will not be damaged and won’t
cause a hazard.
RESETTING THE MOTOR THERMOSTAT
The Ninja®Mega Kitchen System features a unique safety
system which prevents damage to the unit’s motor and drive
system should you inadvertently overload your appliance. If
the appliance is being overloaded, the motor will stop and
the power light will remain lit and speeds 1, 2 and 3 will
flash. To reset the appliance, follow the resetting procedure
below:
1Unplug the appliance from the electrical outlet.
2Remove and empty the container and ensure that no
food is jamming the cutting blades or attachments.
3Allow the appliance to cool for approximately 30
minutes.
4Re-install the container onto the base and re-plug the
appliance into the electrical outlet.
5Proceed to use the appliance as before making sure not
to exceed the recommended maximum capacities.

15 AUST: 1800 890 840 NZ: 0800 002 999
Troubleshooting Guide
PROBLEMS POSSIBLE REASONS & SOLUTIONS
Motor Doesn’t Start or
Attachment Doesn’t Rotate.
Make sure the container is securely placed on motor base.
Make sure the lid is securely on container in the correct position (align arrows).
The appliance is turned “Off”. Press the power button ( ) to turn “On”.
Check that the plug is securely inserted into the electrical outlet.
Check the fuse or circuit breaker.
The unit has overloaded. The appliance will stop and the power light will
remain on while speeds 1, 2 and 3 will flash. Unplug and wait approximately
30 minutes before using again.
The unit has overheated. Unplug and wait approximately 30 minutes before
using again.
Check to make sure the unit is not overloaded.
Food is Unevenly Blended.
Either you are blending too much food at one time, or the pieces are not of
even size and blending smaller amounts per batch.
Food is Blended Too Fine or is
Too Watery.
The food has been over blended. Use pulse button for controlled blending.
Food Collects On Lid or On the
Sides of the Container.
The mixture is to thick. Add more liquid.
You Cannot Achieve Snow
From Solid Ice.
Do not use ice that has been sitting out or has started to melt. Use ice
straight from the freezer.
Motor Base Won’t Stick to
Counter or Table Top.
Make sure surface and suction feet are wiped clean. Suction feet will only
stick to smooth surfaces. Suction feet WILL NOT stick on some surfaces
such as, wood, tile and non-polished finishes.
DO NOT attempt to use appliance when the motor base is stuck to
a surface that is not secure, (cutting board, platter, plates, etc.).

16
AUST: 1800 890 840 NZ: 0800 002 999
Notes

17 AUST: 1800 890 840 NZ: 0800 002 999
Notes

18
AUST: 1800 890 840 NZ: 0800 002 999
ONE (1) YEAR
LIMITED REPLACEMENT WARRANTY STATEMENT
If your product becomes defective due to faulty material or workmanship within a period of 1 year from the date of purchase,
we warrant to do the following:
 • For New Zealand Consumers: We will replace the product with a new product, free of charge, or repair the
product at our cost, at our discretion.
 • For Australian Consumers: Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure.
Your warranty is subject to the following conditions:
 • DO NOT operate the appliance with a damaged plug or cord, or if the unit has been dropped, damaged or dropped
in water. To avoid the risk of electric shock, do not disassemble or attempt to repair the appliance on your own. If the
supply cord is damaged, it must be replaced by a qualified electrician in order to avoid a hazard. Incorrect
re-assembly or repair can cause a risk of electrical shock or injury to persons when the appliance is used.
 • Theproducthasnotbeenmisused,abused,neglected,altered,modiedorrepairedbyanyone.
 • Theproducthasbeensubjectedtofairwearandtear.
 • Theproducthasnotbeenusedfortrade,professionalorhirepurposes.
 • Theproducthasnotsustaineddamagethroughforeignobjects,substancesoraccident.
Your warranty does not cover:
 • Componentsthataresubjecttonaturalwearandtearcausedbynormaluseinaccordancewithoperating
instructions.
 • Unauthorised/impropermaintenance/handlingoroverloadisexcludedfromthiswarranty.
 • Forguaranteeclaimsyouwillneedtosubmitaproofofpurchaseintheformofavalidreceiptthatdisplaysdateand
place of purchase.
This warranty does not replace but is in addition to your statutory rights.
This warranty does not apply to accessories supplied with the product.
This warranty applies only to the original purchaser and may not be transferred.
Replacement products will be covered by the limited warranty for the balance of the warranty period from the date of the
original purchase.
Please note:
Only defective product or parts returned to place of purchase will be replaced under this warranty.
New Zealand Contact Australia Contact
Brand Developers Limited Brand Developers Aust Pty Ltd
Unit H, 686 Rosebank Road, 461 Plummer Street,
Avondale 1026, Auckland, New Zealand PORT MELBOURNE, VIC 3207
FAX: [phone] FAX: [phone]
NZ Customer Care 0800 002 999 AUST Customer Care: 1800 890 840

Copyright © Euro-Pro Operating LLC 2014
Printed In China
Illustrations may differ from actual product.
Euro-Pro and Ninja are trademarks of Euro-Pro Operating LLC.
BL7 70NZ.E.140805.1
Z854
SA A130957E A