Ninja BL685 User manual

Professional Kitchen System
OWNER’S GUIDE
BL685
®
www.ninjakitchen.com
1-877-646-5288

11-877-646-5288
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING ELECTRICAL APPLIANCES,
BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING YOUR
NINJA®PROFESSIONAL KITCHEN SYSTEM.
POLARIZED PLUG
WARNING: To reduce the risk of electric
shock, this appliance has a polarized plug
(one blade is wider than the other). This
plug will fit into a polarized outlet only one
way. If the plug does not fit fully into the
outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install
the proper outlet. DO NOT modify the plug
in any way.
WARNING: Extension cords are
not recommended for use with this
product.
CAUTION: Blades are sharp,
handle with care. When handling the
blades, always hold by the shaft.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
1. CAUTION: Blade assembly is sharp,
handle with care. When handling the blade
assembly, always hold by the shaft.
2. CAUTION: DO NOT BLEND HOT LIQUIDS.
3. IMPORTANT: We do not recommend grinding
in any of our Nutri Ninja®Cups.
4. To protect against electrical shock, do not
submerge the appliance or allow the power cord
to come into contact with water or any other
liquid.
5. DO NOT allow young children to operate the
appliance or use as a toy. Close supervision is
necessary when any appliance is used by or near
children.
6. Never leave an appliance unattended when in
use.
7. Turn the appliance Off and remove the power
cord from the electrical outlet when not in use,
before assembling or disassembling parts and
before cleaning. To unplug, grasp the plug and
pull from the electrical outlet. Never pull from the
power cord.
8. DO NOT abuse the power cord. Never carry
the appliance by the power cord or yank it to
disconnect from electrical outlet; instead grasp
the plug and pull to disconnect.
9. DO NOT operate any appliance with a damaged
cord or plug, or after the appliance malfunctions,
has been dropped or damaged in any manner.
This appliance has no serviceable parts. Return
the appliance to EURO-PRO Operating LLC for
examination, repair or adjustment.

2www.ninjakitchen.com
10. DO NOT let the power cord hang over the edge of
table or counter or touch hot surfaces such as the
stove.
11. Always use appliance on a dry, level surface.
12. Keep hands, hair, clothing, as well as utensils
out of container while processing to reduce the
risk of severe injury to persons or damage to the
appliance. A scraper may be used but only when
the appliance is not running.
13. Avoid contact with moving parts.
14. DO NOT attempt to sharpen blades.
15. DO NOT use the appliance if blade assembly is
bent or damaged.
16. To reduce risk of injury, never place the blade
assembly on base without pitcher or bowl
properly attached.
17. DO NOT operate this appliance on or near any hot
surfaces (such as gas or electric burner or in a
heated oven).
18. The use of attachments or accessories
including canning jars, not recommended by the
manufacturer may result in fire, electric shock or
personal injury.
19. DO NOT remove the container from the motor
base while the appliance is in operation.
20. To reduce the risk of injury, NEVER operate the
appliance without the lid in place.
21. DO NOT try to defeat the interlock mechanism;
make sure that the blade assembly is properly
installed before operating the appliance.
22. DO NOT expose containers to extreme
temperature changes.
23. DO NOT overfill. Never fill past the “Max” line.
24. DO NOT operate the appliance empty.
25. To reduce the risk of burns, always allow the
appliance to cool before taking off parts and
before cleaning.
26. In the event that the unit overheats, the control
panel lights will flash and the unit will shut down.
Unplug the unit and wait 15 minutes to reset.
27. THIS PRODUCT IS INTENDED FOR
HOUSEHOLD USE ONLY. Do not use this
appliance for anything other than its intended use.
Do not use outdoors.
28. The maximum rating is based on the Stacked
Blade Assembly (pitcher) that drives the greatest
power and other recommended attachments may
draw significantly less power or current.
SAVE THESE
INSTRUCTIONS
THIS BOOK COVERS MODEL NUMBERS:
BL685 30
TECHNICAL SPECIFICATIONS
Voltage: 120V., 60Hz.
Power: 1500 Watts
Pitcher Capacity: 72 oz. (9 cups, 2.1 L)
MAX Liquid Capacity: 64 ounces (8 cups, 1.9 L)
Bowl Capacity: 64 oz. (8 cups, 1.8 L)
Nutri Ninja®Capacity: 18 oz. (2¼ cups, 530 mL)
24 oz. (3 cups, 710 mL)

31-877-646-5288
What’s Inside
Pro Extractor
Blades™
(2) Sip &
Seal®Lid
Pitcher Lid
Blender
Pitcher
Food Processor Bowl
Dough Blade
Assembly
(Processor Bowl)
(1) Small 18 oz.
Nutri Ninja®Cup
(1) Regular 24 oz.
Nutri Ninja
®
Cup
Food Processor
Bowl Lid
NOTE: Blades are not interchangeable.
Motor Base
Chopping Blade
Assembly
(Processor Bowl)
Stacked Blade
Assembly (Pitcher)
FEATURES:
• 1500Watts
• ExtraLarge,72ozBlenderPitcher(64ozLiquidCapacity)-BPAFree
• 64oz.BowlwithDrizzleHole-BPAFree
• 18oz.&24oz.NutriNinja®Cups - BPA Free
• 5Speeds,PulseandNutriNinjaFunctionality
• Sturdy,Non-SlipBase
• PatentedNinja®Technology
• TotalCrushing®Technology
• Lock–InLid,FeaturingPourSpout
• EasytoCleanElectronicControlPanel

4www.ninjakitchen.com
Before First Use
CAUTION: Blade assemblies are sharp, not locked in
place and removable, handle with care. When handling
the blade assemblies, always hold them by the shaft.
1Remove all packaging material and labels from the
appliance.
2Wash the lids, pitcher, bowl, Nutri Ninja®cups and
blades in warm, soapy water with a soft cloth.
CAUTION: Handle the blades with care when
washing as they are very sharp.
3Rinse and dry thoroughly.
4The pitcher, bowl, Nutri Ninja®cups, lids and blades
are all dishwasher safe. It is recommended that the lids
and blades be placed on the top rack. Ensure that the
blades are removed from the containers before placing
in the dishwasher.
5Wipe the motor base clean with a damp cloth.
CAUTION: Blade
assembly is not
locked in place.
If using the pour
spout, ensure the
lid is fully locked
onto the blender
pitcher.
CAUTION: Blade
assembly is not
locked in place.
If pouring with
the lid removed,
ALWAYS remove
the stacked blade
assembly first.
PLEASE KEEP THESE IMPORTANT
SAFEGUARDS IN MIND WHEN USING THE
APPLIANCE:
WARNING: Never leave the appliance
unattended while in use.
CAUTION: Blades are sharp! Use extreme
caution when handling the blade
assemblies. Always hold them by the shaft
of the blade assembly.
CAUTION: DO NOT BLEND HOT LIQUIDS.
CAUTION: Never remove the container while
the appliance is still running.
IMPORTANT: We do not recommend grinding
in any of our Nutri Ninja®Cups.
IMPORTANT: Never add ingredients into the
container before placing the attachment in first.
IMPORTANT: Attachments are not
interchangeable.
IMPORTANT: DO NOT attempt to operate the
appliance without the lid on.
IMPORTANT: Never run the appliance empty
IMPORTANT: Appliance accessories are not
intended to be used in the microwave as it
may result in damage to the accessories.

51-877-646-5288
Assembly and Use for the Blender Pitcher
1Place the motor base on a clean, dry, level surface such
as a counter or table top.
2Align and lower the pitcher onto the motor base. (Fig. 1)
Handle should be aligned slightly to the right of the “LOCK”
symbol on the motor base.
3Rotate the pitcher clockwise until it locks in place. You
will hear a click when the lock is engaged. (Fig. 2)
4The pitcher can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 3a, Fig. 3b)
5Holding the Stacked Blade Assembly by the top of the
shaft, place it onto the drive gear inside the pitcher.
Ensure that the stacked
blade assembly is seated
properly and is standing upright. (Fig. 4)
NOTE: The Stacked Blade Assembly will fit loosely on the
drive gear.
6Add the ingredients to the pitcher, making sure that they
do not exceed the highest measured marking line on the
side of the pitcher.
NOTE: If you need to add additional ingredients while
the appliance is processing, open the pour spout cap
and pour the ingredients in through the opening.
NOTE: When blending any kind of liquids, such as
mixtures of any drinks or smoothies, do not exceed the
“Max liquid” mark (64 ounces) on the pitcher.
7Plug the power cord into the electrical outlet and press
the power button ( ).
IMPORTANT: As a safety feature, the power button
() will flash and the motor will not work if the
pitcher and lid are not installed correctly. When
the pitcher and lid are installed properly, the
power button ( ) will be solid, indicating that the
appliance is ready for use.
8Holding the lid by the handle in the upright position, place
it on top of the pitcher aligning the arrow ( ) located on
the lid with the arrow ( ) located on the pitcher’s handle.
(Fig. 5) Press the handle down until you hear a click.
ASSEMBLY
Fig. 3b
Fig. 1
Fig. 4
Fig. 2 Fig. 3a
Fig. 5
WARNING: Never leave the appliance unattended while in use.
CAUTION: Handle the stacked blade assembly with care, as the blades are very sharp.
IMPORTANT: Make sure that the motor base is plugged in for use.

6www.ninjakitchen.com
Fig. 7
USE REMOVAL
Fig. 6 Fig. 8
12 Depending on the consistency of the contents in the
container, open the pour spout cap and use the spout
to empty liquid contents. For thicker consistencies,
remove the lid and blade assembly carefully (by its
shaft), then empty contents from the container.
CAUTION: Stacked blade assembly is not locked
in place. If using the pour spout, ensure the lid is
fully locked onto the blender pitcher.
13 For thicker consistencies, remove the lid and stacked
blade assembly carefully (by its shaft), then empty
contents from the container. To remove the lid, press
the release button on the lid and pull the lid handle up
to a 90°angle and lift the lid off the blender pitcher.
CAUTION: Stacked blade assembly is not locked
in place. If pouring with the lid removed, ALWAYS
remove the stacked blade assembly first.
14 Make sure that the unit is unplugged when not in use.
15 To release the motor base from the counter or table top,
place your hands underneath both sides of the motor base
and gently pull the unit up and towards you. (Fig. 9)
WARNING: Never leave the appliance unattended
while in use.
9Select the speed that best suits your needs. (Fig. 6)
NOTE: Pulse ingredients for even chopping by pressing
down in short intervals.
10 When you have reached your desired consistency, stop
the appliance by pressing the power button ( ) and
wait for the blade assembly to stop turning. (Fig. 7)
11 To remove the lid, press the release button on the lid,
pull the lid handle up to a 90° angle and lift the lid off.
Turn the pitcher counter clockwise and then lift off the
base. (Fig. 7, Fig. 8)
CAUTION: Never insert your hands in the pitcher
as the blades are sharp. Always use a spatula to
dislodge food that has stuck to the sides of the
pitcher.
Fig. 9

71-877-646-5288
1Place the motor base on a clean, dry, level surface such
as a counter or table top.
2Add ingredients to the Nutri Ninja®cup.
NOTE: Do not overfill! To avoid spilling, do not add
ingredients past the “Max” fill line.
3Place the Pro Extractor Blades™onto the cup and screw
it tightly until you have a good seal. (Fig. 1)
4Turn the Nutri Ninja®cup upside down and place it onto
the motor base, aligning the tabs on the cup with the
motor base. Turn the Nutri Ninja®cup clockwise until
it is locked in place. (Fig. 2) Turn the power button on,
the Nutri Ninja®button and Pulse will illuminate.
5Press down on the Pulse button in short intervals to
break down tough ingredients. Press the Nutri Ninja
®
button to activate the 30 second continuous run. (Fig. 3)
The unit will stop after 30 seconds.
Fig. 2
Assembly and Use for the Nutri Ninja®Cup
Fig. 3 Fig. 4 Fig. 5
ASSEMBLY PULSE REMOVAL
6 Once you have reached your desired consistency,
turn the power button off. Turn the Nutri Ninja®cup
counterclockwise and pull straight up to remove.
(Fig. 4) (Fig. 5)
7Turn the cup upright and remove the Pro Extractor
Blades™by twisting the blade assembly counterclockwise.
8Place the Sip & Seal®onto the Nutri Ninja®cup, twist
clockwise to seal and enjoy!
9Make sure that the motor base is unplugged when not
in use.
10 To release the motor base from
the counter or table top, place your
hands underneath both sides of the
motor base and gently pull the unit
up and towards you. (Fig. 6)
NOTE: To order additional Nutri Ninja®
Cups, please visit our website:
www.ninjakitchen.com or feel free to contact
customer service: 1-877-646-5288.
Fig. 1
WARNING: Never leave the appliance unattended while in use.
CAUTION: Handle the blade assemblies with care, as the blades are very sharp.
CAUTION: DO NOT BLEND HOT LIQUIDS.
IMPORTANT: Make sure that the motor base is plugged in for use
Fig. 6

8www.ninjakitchen.com
Assembly and Use for the Food Processor Bowl
ASSEMBLY
Fig. 4 Fig. 5
Fig. 1 Fig. 2 Fig. 3a
Fig. 3b
1Place the motor base on a clean, dry, level surface such
as a counter or table top.
2Align and lower the Bowl onto the motor base. (Fig. 1)
Handle should be aligned slightly to the right of the “LOCK”
symbol on the motor base.
3Rotate the bowl clockwise until you hear a click,
indicating it is locked into place. (Fig. 2)
4The bowl can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 3a, Fig. 3b)
5Holding the desired blade by the top of the shaft, place it onto
the drive gear inside the bowl. Ensure that the attachment is
seated properly and is standing upright. (Fig. 4)
NOTE: The blade assembly will fit loosely on the drive gear.
6Add the ingredients to the bowl, making sure that they
do not exceed the highest measured marking line on
the side of thebowl.
NOTE: The food processor bowl is not intended
for blending drinks. Do not overfill.
7Holding the lid by the handle in the upright position,
place it on top of the bowl aligning the arrow ( )
located on the lid with the arrow ( ) located on the
bowl’s handle. (Fig. 5) Press the handle down until you
hear a click.
NOTE: To add liquids during blending,
open the drizzle hole on the top of the lid
and pour the liquid slowly into the mixture.
7Plug the power cord into the electrical
outlet and press the power button ( ).
IMPORTANT : As a safety feature, the power
button ( ) will flash and the motor will not work
if the bowl and lid are not installed correctly.
When the bowl and lid are installed properly, the
power button ( ) will be solid, indicating that the
appliance is ready for use.
NOTE: Do not exceed the highest measured marking line
on the side of the bowl. For meats do not exceed 34 oz
bowl mark.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Handle the chopping blade assembly with care, as the blades are very sharp.
IMPORTANT: Make sure that the motor base is plugged in for use.

91-877-646-5288
USING THE CHOPPING BLADE ASSEMBLY
1Holding the chopping blade assembly by the shaft,
place it onto the gear shaft inside the bowl. Ensure that
the attachment fits around the gear shaft and that it is
standing straight. (Fig. 1)
2Add the ingredients and secure the bowl lid onto the bowl.
3Plug the power cord into the electrical outlet and press
on the power button ( ).
4Select the speed that best suits your needs. Pulse
ingredients evenly by pressing down in short intervals.
NOTE: Please refer to “Speed Settings & Uses” chart
for suggested uses and speeds.
5When you have reached your desired consistency, stop
the appliance by pressing the power button ( ) and
wait for the blade to stop turning.
6To remove the lid, pull the lid handle up to a 90°
angle and lift the lid off. (Fig. 2) Turn the bowl
counterclockwise and then lift off the base. (Fig. 3)
CAUTION: If pouring from the bowl, ALWAYS remove
the chopping blade assembly before pouring.
7To release the motor base from the counter or table top,
place your hands underneath both sides of the motor
base and gently pull the unit up and towards you. (Fig. 4)
USE
USING THE DOUGH BLADE ASSEMBLY
1Holding the dough blade assembly by the shaft, place
it onto the gear shaft inside the bowl. Ensure that the
attachment fits around the gear shaft and that it is
standing straight. (Fig. 5)
2Add the ingredients and secure the bowl lid onto the bowl.
3Plug the power cord into the electrical outlet and press
on the power button ( ). Select speed button 1 on
the control panel and process until ingredients come
together to form a mass.
NOTE: Please refer to “Speed Settings & Uses” chart
for suggested uses and speeds.
4Once finished making dough, stop the appliance by
pressing the power button ( ) and wait for the blade
assembly to stop turning.
5To remove the lid, pull the lid handle up to a 90°
angle and lift the lid off. (Fig. 2) Turn the bowl
counterclockwise and then lift off the base. (Fig. 3)
6To release the motor base from the counter or table top,
place your hands underneath both sides of the motor
base and gently pull the unit up and towards you. (Fig. 4)
Fig. 1 Fig. 5
REMOVAL USE
WARNING: Never leave the appliance unattended while in use.
CAUTION: Handle the chopping blade assembly with care, as the blades are very sharp.
IMPORTANT: Make sure that the motor base is plugged in for use.
Fig. 4Fig. 2 Fig. 3

10www.ninjakitchen.com
FUNCTION CONTAINER ATTACHMENT SPEED BUTTON TYPE OF FOOD
Small Batch
Blending Nutri Ninja®Cup Pro Extractor Blade™NUTRI NINJA®
Ultra Smooth Nutrient Extractions*/
Smoothies
Ultra Smooth Purees
Sauces
Ultra Smooth Soups
Small Batch Chopping Nutri Ninja®Cup Pro Extractor Blade™PULSE Chopped Nuts
Small Batch
Processing Nutri Ninja®Cup Pro Extractor Blade™
PULSE, held down
Crushed Ice
Ice to Snow
Grated Hard Cheese
Dough Making Food Processor Dough Blade
Assembly
1
DOUGH
Bread Dough
Pie Dough
Pizza Dough
Pretzel Dough
Cookie Dough
Pasta Dough
Batters Food Processor Chopping Blade
Assembly
2
MIX
Cakes
Muffins
Pancake Batter
Cheesecake
Brownies
Dressings and
Sauces Food Processor Chopping Blade Assembly
3
PUREE
Vinaigrettes
Aiolis
Sauces
Marinades
Purees and Dips Food Processor Chopping Blade
Assembly
4
BLEND
Pestos
Hummus
Vegetable Purees
Fruit Purees
Cream Cheese Dips
Chopping Food Processor Chopping Blade
Assembly PULSE
Vegetables
Chopped Salads
Chutneys
Burgers
Sausage Patties
Meatballs
Meatloaf
Eggs Pitcher Stacked Blade
Assembly
2
MIX
Omelets
Scrambled Eggs
Stratas
Frittatas
Nut Butters Pitcher Stacked Blade
Assembly
3
PUREE
Almond Butter
Peanut Butter
Soups and
Sauces** Pitcher Stacked Blade Assembly
4
BLEND
Tomato Soup
Tomato Sauce
Root Vegetable Soup
Large Batch Drink
Making Pitcher Stacked Blade Assembly
5
CRUSH
Frozen Cocktail
Milkshakes
Frappes
Smoothies
Speed Setting & Uses
* Extract a nutritious drink containing vitamin and nutrients from fruits and veggies.
** When blending soups or sauces, make sure they’re cooled to room temperature first - Ninja containers are not
intended for hot blending

11 1-877-646-5288
Care & Maintenance
HOW TO CLEAN
CAUTION: Make sure that the motor base is
unplugged from the power source before inserting
or removing any attachment and before cleaning.
CAUTION: DO NOT immerse the motor base into
water or any other liquid.
CAUTION: Handle the blade assemblies with care,
as the blades are very sharp.
1Separate/remove all parts from each other.
2Clean the motor base with a damp cloth and wipe dry.
3Place the pitcher, Nutri Ninja®cup and Food Processor
Bowl in the dishwasher. Place the lids and blades on
the top rack.
OR
4 Carefully hand wash the lids, pitcher, bowl, Nutri Ninja®
cups and blade assemblies in warm, soapy water with a
soft cloth.
Please call customer service if any servicing needs to
be performed on the appliance at 1-877-646-5288.
NUTRI NINJA®PRO EXTRACTOR BLADES™
When washing the Pro Extractor Blades™, do not
attempt to remove the seal. Removing the seal can
cause damage to the seal which can result in improper
reassembly and leaking.
If the blade seal becomes loose, please call customer
service at 1-877-646-5288.
HOW TO STORE
1Store the Ninja®Professional Kitchen System upright
with the pitcher on the motor base, Stacked Blade
Assembly inside the pitcher and the lid locked
on the pitcher. Do not place anything on top. Store
the Food Processor Bowl with the Chopping Blade
assembly inside and the lid on top. Store the Nutri
Ninja®cup with the blade assembly attached to the cup
and all other attachments along side the appliance or
in a cabinet where they will not be damaged and won’t
cause a hazard.
RESETTING THE MOTOR THERMOSTAT
The Ninja®Professional Kitchen System features a unique
safety system which prevents damage to the unit’s motor
and drive system should you inadvertently overload your
appliance.If the appliance is being overloaded, the
motor will stop. Allow the appliance to cool for
approximately 15 minutes. To reset the appliance, follow
the resetting procedure below:
1Unplug the appliance from the electrical outlet.
2Remove and empty the container and ensure that no
food is jamming the blade assembly.
3Allow the appliance to cool for approximately 15
minutes.
4Re-install the container onto the base and re-plug the
appliance into the electrical outlet.
5Proceed to use the appliance as before making sure not
to exceed the recommended maximum capacities.

12www.ninjakitchen.com
Troubleshooting Guide
Replacement Parts
ORDERING REPLACEMENT PARTS
To order additional parts and attachments, please visit our website: www.ninjakitchen.com
or feel free to contact customer service: 1-877-646-5288.
PROBLEMS POSSIBLE REASONS & SOLUTIONS
Motor doesn’t start or
attachment doesn’t rotate.
Make sure the container is securely placed on motor base.
Make sure the lid is securely on container in the correct position (align arrows).
The appliance is turned “Off”. Press the power button ( ) to turn “On”.
Check that the plug is securely inserted into the electrical outlet.
Check the fuse or circuit breaker.
The unit has overheated or overloaded. Unplug and wait approximately 15
minutes before using again.
Food is unevenly chopped.
Either you are chopping too much food at one time, or the pieces are not of
an even size. Try processing smaller amounts per batch.
Food is chopped too fine or is
too watery.
The food has been over processed. Use pulse button for controlled
processing.
Food collects on lid or on the
sides of the container.
The mixture is to thick. Add more liquid.
You cannot achieve snow
from solid ice.
Do not use ice that has been sitting out or has started to melt. Use ice
straight from the freezer.
Motor base won’t stick to
counter or table top.
Make sure surface and suction feet are wiped clean. Suction feet will only
stick to smooth surfaces. Suction feet WILL NOT stick on some surfaces
such as, wood, tile and non-polished finishes.
DO NOT attempt to use appliance when the motor base is stuck to a
surface that is not secure, (cutting board, platter, plates, etc.).
Leaking is occurring when
using the Nutri Ninja®cup.
Ensure the blade is properly twisted into the cup and sealed tightly into
place. Check to see that the lid gasket is properly in place.
Do not overfill the cup. Never add ingredients past the “Max” fill line.
Ingredients are stuck and not
fully blending.
You may have overloaded the Nutri Ninja®cup. Try pulsing 3-5 times and
then resume blending. You may also add liquid to make blending easier.
The Nutri Ninja®button does
not work.
The Nutri Ninja®button will only operate when you have the Nutri Ninja®
cup assembled to the motor base. This function was designed specifically
for the Nutri Ninja Cups to operate at the ideal speed. This function is
programmed to shut off after 30 seconds.

13 1-877-646-5288
Notes

14www.ninjakitchen.com
PRODUCT REGISTRATION
Please visit www.ninjakitchen.com or call 1-877-646-5288 to register your new Ninja®product within ten
(10) days of purchase. You will be asked to provide the store name, date of purchase and model number along
with your name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering
you acknowledge to have read and understood the instructions for use, and warnings set forth in the
accompanying instructions.
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a
period of one (1) year from the date of purchase when utilized for normal household use, subject to the following
conditions, exclusions and exceptions.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit
at our option. This Limited Warranty does not cover normal wear of parts and does not apply to any unit that
has been tampered with or used for commercial purposes. This Limited Warranty does not cover damage
caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This
Limited Warranty does not cover damage or defects caused by or resulting from damages from shipping or
repairs, service or alteration to the product or any of its parts, which have been performed by a repair person not
authorized by EURO-PRO Operating LLC.
If your appliance fails to operate properly while in use under normal household conditions within the warranty
period, return the complete appliance and accessories, freight prepaid. For assistance with warranty service
options or customer support, please call our customer care and product specialists at , call 1-877-646-5288 or
visit our website www.ninjakitchen.com.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair
or replace it free of charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost of
return freight. *
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations
expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO Operating LLC
liable for incidental or consequential damages to anyone of any nature whatsoever. Some states do not permit the
exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to
state or from province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase
date and to attach tag to item before packing with your name, complete address and phone number
with a note giving purchase information, model number and what you believe is the problem with
the item. We recommend you insure the package (as damage in shipping is not covered by your
Limited Warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”.

Euro-Pro Operating LLC
US: Newton, MA 02459
CAN: Ville St-Laurent, QC H4S 1A7
1-877-646-5288
www.ninjakitchen.com
Euro-Pro, Ninja, Nutri Ninja, Sip & Seal and Total Crushing are registered
trademarks of Euro-Pro Operating LLC.
Pro Extractor Blades is a trademark of Euro-Pro Operating LLC.
For Shark
I
Ninja U.S. Patent information visit
http://www.europro.com/USPatents
Illustrations may differ from actual product. We are constantly striving to
improve our products, therefore the specifications contained herein are subject
to change without notice.
© 2015 Euro-Pro Operating LLC
BL685_Series_30_IB_ENG_150529_1
PRINTED IN CHINA