Ninja PROFESSIONAL FOOD PROCESSOR WITH AUTO-IQ User manual

For questions or to register your product,
visit us online at ninjakitchen.com
@ninjakitchen
© 2020 SharkNinja Operating LLC.
AUTO-IQ, NINJA, and PRECISION PROCESSOR are registered trademarks of SharkNinja Operating LLC.
BN600_Series_QSG_MP_Mv4
PROFESSIONAL FOOD PROCESSOR WITH AUTO-IQ®
QUICK ASSEMBLY
Please make sure to read the enclosed Ninja® Owner’s Guide prior to using your unit.
NINJA® PROFESSIONAL FOOD PROCESSOR WITH AUTO-IQ®
WARNING: Always unplug the base before cleaning.
Dishwasher: The bowl, lid, disc, and blade
assemblies are top-rack dishwasher safe.
Ensure the blade assembly is removed from
the bowl before placing in the dishwasher.
Exercise care when handling blade assemblies.
Hand-washing: Wash bowl, lid, disc, and blade
assemblies in warm, soapy water. Exercise care
when washing the blade assemblies. Use a
dishwashing utensil with a handle to avoid direct
hand contact with blades. Rinse and air-dry
thoroughly.
Intelligent preset programs combine unique blending and pausing patterns
that do the work for you. Once an Auto-iQ program is selected, it will start immediately
and automatically stop when processing is complete. To stop processing before
the end of a program, press the currently active button again.
NOTE: Program run times vary from a few seconds to up a minute.
IMPORTANT: DO NOT run the unit on HIGH if using the dough blade.
The unit is NOT intended to crush ice. Refer to the warnings on pages 4–6 in the Owner's Guide.
AUTO-IQ PROGRAMS
MANUAL PROGRAMS
CLEANING
LOW and HIGH: When selected, each
of these speeds runs continuously
for 60 seconds. They do not work in
conjunction with any Auto-iQ programs.
PULSE: Oers greater control of pulsing and
processing. Operates only when PULSE is
pressed. Use short presses for short pulses
and long presses for long pulses.
CHOP
Timed pulses and pauses give you
consistent chopping results. Run program
once for a large chop, twice for a small chop
and three times if you prefer to mince.
DOUGH
Ideal for creating delicious dough,
from pie to pizza to cookie doughs.
NOTE: Use PULSE to add mix-ins, such as
chocolate chips or raisins, after dough
program has completed.
PUREE
(Not available on all models)
Create anything from silky-smooth
sauces to the perfect hummus.
DISC
Slice or shred a variety of ingredients,
from fresh vegetables to cheeses. FOOD PROCESSOR
PROFESSIONAL
WITH AUTO-IQ®

Trim ingredients so they are
in 4" to 5" pieces or slightly over
the height of the feed chute.
DO NOT cut ingredients smaller
than the size of the feed chute.
Cut both ends o ingredients
to create flat surfaces.
Trim tapered ingredients like
carrots to make them more
symmetrical.
Larger ingredients, such
as potatoes, may need to
be cut in half lengthwise.
5" 5"
USING THE CHOPPING & DOUGH BLADE ASSEMBLIES
1.
Select DISC or LOW. The
disc will begin spinning.
IMPORTANT: Use only the DISC
program or LOW setting when
using the Slicing/Shredding Disc.
2.
Add ingredients through
the feed chute on the lid.
Use the food pusher to
help guide the ingredients.
4.
Remove bowl from base by
turning it counterclockwise,
then lifting it up.
PARTS
FOOD PREP
ASSEMBLY
PRECISION
PROCESSOR®
BOWL
PRECISION
PROCESSOR
BOWL LID WITH
FOOD PUSHER
DISC SPINDLE REVERSIBLE
SLICING/SHREDDING
DISC
3.
The disc will automatically stop
spinning at the end of the program.
Wait for disc to stop turning, then
press the button on the feed chute
lid near the handle to unlock. Turn
lid counterclockwise and lift lid
from bowl. Remove disc and spindle
before emptying.
USING THE REVERSIBLE SLICING/SHREDDING DISC
4.
Place feed chute lid
on bowl and turn
clockwise to lock
in place.
2.
Install the disc
spindle in the bowl.
1.
Place Precision Processor
Bowl on base and turn
clockwise to lock in place.
PROCESS & ENJOY
1.
Select any
program to
begin processing.
2.
When processing is
complete, press button
on feed chute lid near
handle to unlock. Turn lid
counterclockwise and lift
from bowl.
Remove blade assembly
before emptying bowl.
PARTS
3.
Place feed chute lid
on bowl and turn
clockwise to lock in
place.
ASSEMBLY
WARNING: Chopping Blade Assembly is sharp and not locked in place. Before pouring, carefully
remove Chopping Blade Assembly. Failure to do so will result in a risk of laceration. Refer to the
Ninja Owner’s Guide for additional information.
1.
Place Precision
Processor Bowl
on base and turn
clockwise to lock
in place.
PRECISION
PROCESSOR®
BOWL
PRECISION
PROCESSOR
BOWL LID WITH
FOOD PUSHER
CHOPPING BLADE
ASSEMBLY
DOUGH BLADE
ASSEMBLY
3.
Remove bowl from
base by turning it
counterclockwise,
then lifting it up.
2.
Holding the blade
assembly by the top
of the shaft, install it
in bowl.
3.
Use the finger holes to grasp
disc and place it over the
spindle, with the side you
would like to use facing up.
NOTE: The Slicing/Shredding
Disc is reversible. Use the side
labeled “Slicer” for slicing and
the side labeled “Shredder” for
shredding.
NOTE: Ensure cheese is well chilled before slicing/shredding. DO NOT slice or shred frozen cheese.
SHREDDING
SLICE/SHRED & ENJOY
Once the Precision Processor Bowl is locked onto base, plug in the unit,
then press the Power button to turn the unit on.
Once the Precision Processor Bowl is locked onto the base, plug in the unit,
then press the Power button to turn the unit on.
S
H
R
E
D
D
E
R
SLICING
S
L
I
C
E
R

Trim ingredients so they are
in 4" to 5" pieces or slightly over
the height of the feed chute.
DO NOT cut ingredients smaller
than the size of the feed chute.
Cut both ends o ingredients
to create flat surfaces.
Trim tapered ingredients like
carrots to make them more
symmetrical.
Larger ingredients, such
as potatoes, may need to
be cut in half lengthwise.
5" 5"
USING THE CHOPPING & DOUGH BLADE ASSEMBLIES
1.
Select DISC or LOW. The
disc will begin spinning.
IMPORTANT: Use only the DISC
program or LOW setting when
using the Slicing/Shredding Disc.
2.
Add ingredients through
the feed chute on the lid.
Use the food pusher to
help guide the ingredients.
4.
Remove bowl from base by
turning it counterclockwise,
then lifting it up.
PARTS
FOOD PREP
ASSEMBLY
PRECISION
PROCESSOR®
BOWL
PRECISION
PROCESSOR
BOWL LID WITH
FOOD PUSHER
DISC SPINDLE REVERSIBLE
SLICING/SHREDDING
DISC
3.
The disc will automatically stop
spinning at the end of the program.
Wait for disc to stop turning, then
press the button on the feed chute
lid near the handle to unlock. Turn
lid counterclockwise and lift lid
from bowl. Remove disc and spindle
before emptying.
USING THE REVERSIBLE SLICING/SHREDDING DISC
4.
Place feed chute lid
on bowl and turn
clockwise to lock
in place.
2.
Install the disc
spindle in the bowl.
1.
Place Precision Processor
Bowl on base and turn
clockwise to lock in place.
PROCESS & ENJOY
1.
Select any
program to
begin processing.
2.
When processing is
complete, press button
on feed chute lid near
handle to unlock. Turn lid
counterclockwise and lift
from bowl.
Remove blade assembly
before emptying bowl.
PARTS
3.
Place feed chute lid
on bowl and turn
clockwise to lock in
place.
ASSEMBLY
WARNING: Chopping Blade Assembly is sharp and not locked in place. Before pouring, carefully
remove Chopping Blade Assembly. Failure to do so will result in a risk of laceration. Refer to the
Ninja Owner’s Guide for additional information.
1.
Place Precision
Processor Bowl
on base and turn
clockwise to lock
in place.
PRECISION
PROCESSOR®
BOWL
PRECISION
PROCESSOR
BOWL LID WITH
FOOD PUSHER
CHOPPING BLADE
ASSE M B LY
DOUGH BLADE
ASSE M B LY
3.
Remove bowl from
base by turning it
counterclockwise,
then lifting it up.
2.
Holding the blade
assembly by the top
of the shaft, install it
in bowl.
3.
Use the finger holes to grasp
disc and place it over the
spindle, with the side you
would like to use facing up.
NOTE: The Slicing/Shredding
Disc is reversible. Use the side
labeled “Slicer” for slicing and
the side labeled “Shredder” for
shredding.
NOTE: Ensure cheese is well chilled before slicing/shredding. DO NOT slice or shred frozen cheese.
SHREDDING
SLICE/SHRED & ENJOY
Once the Precision Processor Bowl is locked onto base, plug in the unit,
then press the Power button to turn the unit on.
Once the Precision Processor Bowl is locked onto the base, plug in the unit,
then press the Power button to turn the unit on.
S
H
R
E
D
D
E
R
SLICING
S
L
I
C
E
R
Trim ingredients so they are
in 4" to 5" pieces or slightly over
the height of the feed chute.
DO NOT cut ingredients smaller
than the size of the feed chute.
Cut both ends o ingredients
to create flat surfaces.
Trim tapered ingredients like
carrots to make them more
symmetrical.
Larger ingredients, such
as potatoes, may need to
be cut in half lengthwise.
5" 5"
USING THE CHOPPING & DOUGH BLADE ASSEMBLIES
1.
Select DISC or LOW. The
disc will begin spinning.
IMPORTANT: Use only the DISC
program or LOW setting when
using the Slicing/Shredding Disc.
2.
Add ingredients through
the feed chute on the lid.
Use the food pusher to
help guide the ingredients.
4.
Remove bowl from base by
turning it counterclockwise,
then lifting it up.
PARTS
FOOD PREP
ASSEMBLY
PRECISION
PROCESSOR®
BOWL
PRECISION
PROCESSOR
BOWL LID WITH
FOOD PUSHER
DISC SPINDLE REVERSIBLE
SLICING/SHREDDING
DISC
3.
The disc will automatically stop
spinning at the end of the program.
Wait for disc to stop turning, then
press the button on the feed chute
lid near the handle to unlock. Turn
lid counterclockwise and lift lid
from bowl. Remove disc and spindle
before emptying.
USING THE REVERSIBLE SLICING/SHREDDING DISC
4.
Place feed chute lid
on bowl and turn
clockwise to lock
in place.
2.
Install the disc
spindle in the bowl.
1.
Place Precision Processor
Bowl on base and turn
clockwise to lock in place.
PROCESS & ENJOY
1.
Select any
program to
begin processing.
2.
When processing is
complete, press button
on feed chute lid near
handle to unlock. Turn lid
counterclockwise and lift
from bowl.
Remove blade assembly
before emptying bowl.
PARTS
3.
Place feed chute lid
on bowl and turn
clockwise to lock in
place.
ASSEMBLY
WARNING: Chopping Blade Assembly is sharp and not locked in place. Before pouring, carefully
remove Chopping Blade Assembly. Failure to do so will result in a risk of laceration. Refer to the
Ninja Owner’s Guide for additional information.
1.
Place Precision
Processor Bowl
on base and turn
clockwise to lock
in place.
PRECISION
PROCESSOR®
BOWL
PRECISION
PROCESSOR
BOWL LID WITH
FOOD PUSHER
CHOPPING BLADE
ASSEMBLY
DOUGH BLADE
ASSEMBLY
3.
Remove bowl from
base by turning it
counterclockwise,
then lifting it up.
2.
Holding the blade
assembly by the top
of the shaft, install it
in bowl.
3.
Use the finger holes to grasp
disc and place it over the
spindle, with the side you
would like to use facing up.
NOTE: The Slicing/Shredding
Disc is reversible. Use the side
labeled “Slicer” for slicing and
the side labeled “Shredder” for
shredding.
NOTE: Ensure cheese is well chilled before slicing/shredding. DO NOT slice or shred frozen cheese.
SHREDDING
SLICE/SHRED & ENJOY
Once the Precision Processor Bowl is locked onto base, plug in the unit,
then press the Power button to turn the unit on.
Once the Precision Processor Bowl is locked onto the base, plug in the unit,
then press the Power button to turn the unit on.
S
H
R
E
D
D
E
R
SLICING
S
L
I
C
E
R

Trim ingredients so they are
in 4" to 5" pieces or slightly over
the height of the feed chute.
DO NOT cut ingredients smaller
than the size of the feed chute.
Cut both ends o ingredients
to create flat surfaces.
Trim tapered ingredients like
carrots to make them more
symmetrical.
Larger ingredients, such
as potatoes, may need to
be cut in half lengthwise.
5" 5"
USING THE CHOPPING & DOUGH BLADE ASSEMBLIES
1.
Select DISC or LOW. The
disc will begin spinning.
IMPORTANT: Use only the DISC
program or LOW setting when
using the Slicing/Shredding Disc.
2.
Add ingredients through
the feed chute on the lid.
Use the food pusher to
help guide the ingredients.
4.
Remove bowl from base by
turning it counterclockwise,
then lifting it up.
PARTS
FOOD PREP
ASSEMBLY
PRECISION
PROCESSOR®
BOWL
PRECISION
PROCESSOR
BOWL LID WITH
FOOD PUSHER
DISC SPINDLE REVERSIBLE
SLICING/SHREDDING
DISC
3.
The disc will automatically stop
spinning at the end of the program.
Wait for disc to stop turning, then
press the button on the feed chute
lid near the handle to unlock. Turn
lid counterclockwise and lift lid
from bowl. Remove disc and spindle
before emptying.
USING THE REVERSIBLE SLICING/SHREDDING DISC
4.
Place feed chute lid
on bowl and turn
clockwise to lock
in place.
2.
Install the disc
spindle in the bowl.
1.
Place Precision Processor
Bowl on base and turn
clockwise to lock in place.
PROCESS & ENJOY
1.
Select any
program to
begin processing.
2.
When processing is
complete, press button
on feed chute lid near
handle to unlock. Turn lid
counterclockwise and lift
from bowl.
Remove blade assembly
before emptying bowl.
PARTS
3.
Place feed chute lid
on bowl and turn
clockwise to lock in
place.
ASSEMBLY
WARNING: Chopping Blade Assembly is sharp and not locked in place. Before pouring, carefully
remove Chopping Blade Assembly. Failure to do so will result in a risk of laceration. Refer to the
Ninja Owner’s Guide for additional information.
1.
Place Precision
Processor Bowl
on base and turn
clockwise to lock
in place.
PRECISION
PROCESSOR®
BOWL
PRECISION
PROCESSOR
BOWL LID WITH
FOOD PUSHER
CHOPPING BLADE
ASSEMBLY
DOUGH BLADE
ASSEMBLY
3.
Remove bowl from
base by turning it
counterclockwise,
then lifting it up.
2.
Holding the blade
assembly by the top
of the shaft, install it
in bowl.
3.
Use the finger holes to grasp
disc and place it over the
spindle, with the side you
would like to use facing up.
NOTE: The Slicing/Shredding
Disc is reversible. Use the side
labeled “Slicer” for slicing and
the side labeled “Shredder” for
shredding.
NOTE: Ensure cheese is well chilled before slicing/shredding. DO NOT slice or shred frozen cheese.
SHREDDING
SLICE/SHRED & ENJOY
Once the Precision Processor Bowl is locked onto base, plug in the unit,
then press the Power button to turn the unit on.
Once the Precision Processor Bowl is locked onto the base, plug in the unit,
then press the Power button to turn the unit on.
S
H
R
E
D
D
E
R
SLICING
S
L
I
C
E
R

For questions or to register your product,
visit us online at ninjakitchen.com
@ninjakitchen
© 2020 SharkNinja Operating LLC.
AUTO-IQ, NINJA, and PRECISION PROCESSOR are registered trademarks of SharkNinja Operating LLC.
BN600_Series_QSG_MP_Mv4
PROFESSIONAL FOOD PROCESSOR WITH AUTO-IQ®
QUICK ASSEMBLY
Please make sure to read the enclosed Ninja® Owner’s Guide prior to using your unit.
NINJA® PROFESSIONAL FOOD PROCESSOR WITH AUTO-IQ®
WARNING: Always unplug the base before cleaning.
Dishwasher: The bowl, lid, disc, and blade
assemblies are top-rack dishwasher safe.
Ensure the blade assembly is removed from
the bowl before placing in the dishwasher.
Exercise care when handling blade assemblies.
Hand-washing: Wash bowl, lid, disc, and blade
assemblies in warm, soapy water. Exercise care
when washing the blade assemblies. Use a
dishwashing utensil with a handle to avoid direct
hand contact with blades. Rinse and air-dry
thoroughly.
Intelligent preset programs combine unique blending and pausing patterns
that do the work for you. Once an Auto-iQ program is selected, it will start immediately
and automatically stop when processing is complete. To stop processing before
the end of a program, press the currently active button again.
NOTE: Program run times vary from a few seconds to up a minute.
IMPORTANT: DO NOT run the unit on HIGH if using the dough blade.
The unit is NOT intended to crush ice. Refer to the warnings on pages 4–6 in the Owner's Guide.
AUTO-IQ PROGRAMS
MANUAL PROGRAMS
CLEANING
LOW and HIGH: When selected, each
of these speeds runs continuously
for 60 seconds. They do not work in
conjunction with any Auto-iQ programs.
PULSE: Oers greater control of pulsing and
processing. Operates only when PULSE is
pressed. Use short presses for short pulses
and long presses for long pulses.
CHOP
Timed pulses and pauses give you
consistent chopping results. Run program
once for a large chop, twice for a small chop
and three times if you prefer to mince.
DOUGH
Ideal for creating delicious dough,
from pie to pizza to cookie doughs.
NOTE: Use PULSE to add mix-ins, such as
chocolate chips or raisins, after dough
program has completed.
PUREE
(Not available on all models)
Create anything from silky-smooth
sauces to the perfect hummus.
DISC
Slice or shred a variety of ingredients,
from fresh vegetables to cheeses. FOOD PROCESSOR
PROFESSIONAL
WITH AUTO-IQ®

For questions or to register your product,
visit us online at ninjakitchen.com
@ninjakitchen
© 2020 SharkNinja Operating LLC.
AUTO-IQ, NINJA, and PRECISION PROCESSOR are registered trademarks of SharkNinja Operating LLC.
BN600_Series_QSG_MP_Mv4
PROFESSIONAL FOOD PROCESSOR WITH AUTO-IQ®
QUICK ASSEMBLY
Please make sure to read the enclosed Ninja® Owner’s Guide prior to using your unit.
NINJA® PROFESSIONAL FOOD PROCESSOR WITH AUTO-IQ®
WARNING: Always unplug the base before cleaning.
Dishwasher: The bowl, lid, disc, and blade
assemblies are top-rack dishwasher safe.
Ensure the blade assembly is removed from
the bowl before placing in the dishwasher.
Exercise care when handling blade assemblies.
Hand-washing: Wash bowl, lid, disc, and blade
assemblies in warm, soapy water. Exercise care
when washing the blade assemblies. Use a
dishwashing utensil with a handle to avoid direct
hand contact with blades. Rinse and air-dry
thoroughly.
Intelligent preset programs combine unique blending and pausing patterns
that do the work for you. Once an Auto-iQ program is selected, it will start immediately
and automatically stop when processing is complete. To stop processing before
the end of a program, press the currently active button again.
NOTE: Program run times vary from a few seconds to up a minute.
IMPORTANT: DO NOT run the unit on HIGH if using the dough blade.
The unit is NOT intended to crush ice. Refer to the warnings on pages 4–6 in the Owner's Guide.
AUTO-IQ PROGRAMS
MANUAL PROGRAMS
CLEANING
LOW and HIGH: When selected, each
of these speeds runs continuously
for 60 seconds. They do not work in
conjunction with any Auto-iQ programs.
PULSE: Oers greater control of pulsing and
processing. Operates only when PULSE is
pressed. Use short presses for short pulses
and long presses for long pulses.
CHOP
Timed pulses and pauses give you
consistent chopping results. Run program
once for a large chop, twice for a small chop
and three times if you prefer to mince.
DOUGH
Ideal for creating delicious dough,
from pie to pizza to cookie doughs.
NOTE: Use PULSE to add mix-ins, such as
chocolate chips or raisins, after dough
program has completed.
PUREE
(Not available on all models)
Create anything from silky-smooth
sauces to the perfect hummus.
DISC
Slice or shred a variety of ingredients,
from fresh vegetables to cheeses. FOOD PROCESSOR
PROFESSIONAL
WITH AUTO-IQ®