INGREDIENTS
1 tablespoon (1/2ounce) cream cheese
1/3cup granulated sugar
3/4cup heavy cream
Flavoring, 1 teaspoon extract of your choice
OR 2 tablespoons of cocoa powder
1 cup whole milk
1/4cup of your favorite mix-ins (optional)
PICK YOUR MIX-INS TO ADD A PERSONAL TOUCH
Perfectly personalized ice cream
PREP: 5 minutes | FREEZE: 24 hours | PROGRAM TIME: 1 1/2minutes | MAKES: 4 servings
Microwave the cream
cheese for 10 seconds.
Add sugar and flavor,
then whisk the mixture
until it looks like frosting.
Slowly mix in heavy
cream and milk until
sugar is dissolved.
Pour base into
CREAMi®Breeze™Pint.
Place storage lid on
pint and freeze for
24 hours.
Remove storage lid
from frozen pint.
Refer to next page for
Assembly & process
instructions.
Select ICE CREAM.
With a spoon, create a 1 1/2-inch
wide hole that reaches the
bottom of the pint.
Add mix-ins to the hole in the
pint and process again using
the MIX-IN program.
1/4cup of your favorite crushed candies, frozen fruits, chopped nuts,
chocolate pieces, and more.
PICK YOUR FLAVOR
Vanilla extractCocoa powder Mint extract Fruit extract
Almond extract
2.
Prepare
CREAMi® Breeze™ Pint
Remove storage lid from
frozen CREAMi Breeze
Pint and check that the
ingredients have not been
frozen at an angle.
4.
Install
Processing Lid
Position the processing
lid on top of the CREAMi
Breeze Pint. Twist the lid
clockwise to secure pint.
This can be verified by
ensuring that the arrow
on the processing lid is
aligned with one of the
arrows on the pint.
Assembly & process
5.
Install CREAMi Breeze Pint
Insert the CREAMi Breeze Pint into
the motor base. Rotate clockwise
to lock, until you hear a click.
1.
Plug in
unit first
The unit will not run
if the CREAMi Breeze
Pint is installed
before the unit
is plugged in.
6.
Select program
Press the power button,
then press the program
that suits your recipe.
7.
Remove CREAMi Breeze Pint
When the program ends, press the
release button on the front of the motor
base to remove the CREAMi Breeze Pint.
8.
Remove
Processing Lid
Rotate processing lid
counterclockwise
to separate from
CREAMi Breeze Pint.
Release Button
To remove the pint,
press and hold
release button.
If adding mix-ins, use a
spoon to create a 1 1/2-inch
wide hole that reaches the
bottom of the pint.
Add chopped or broken
mix-ins to the hole in the
pint and process again
using the MIX-IN program.
If not adding mix-ins,
RE-SPIN can be used on
a crumbly or powdery
pint to make it creamy.
RE-SPIN is often needed
for very cold bases.
Do not RE-SPIN before
using MIX-IN program.
OR
SCAN & WATCH
HOW IT WORKS
ninjacreami.com
MAKE IT DAIRY-FREE Use vegan cream cheese for cream cheese, unsweetened coconut cream
for heavy cream, and unsweetened oat milk for milk. Whisk the coconut cream until smooth,
then add the remaining ingredients.
9.
3.
Install
Creamerizer™ Paddle
Press and hold the paddle
latch on the top of the
processing lid, then insert
the paddle in the bottom of
the processing lid. Release the
latch to secure the paddle.
If the install light is blinking and the power light is solid, make sure the pint is properly installed,
and the lid is fully secured. This can be verified by ensuring that the arrow on the processing lid
is aligned with one of the arrows on the pint. If both the power light and install light are flashing,
make sure the paddle is installed into the processing lid.
NOTE
