Ninja DIN 300 User manual

www.Ninjapaintball.com
1
NINJA
Proudly Made in the USA
DIN 300 PCP FILL STATION
SAFETY FIRST!
March 2013
ALWAYS KEEP ALL PETROLEUM LUBRICANTS AWAY FROM PARTS OF
THE PCP FILL ADAPTER. PETROLEUM LUBRICANTS MAY CAUSE FIRE OR
EXPLOSION IF ENTERED INTO THE HIGH PRESSURE TUBE OF YOUR PCP
AIRGUN.
ALWAYS READ AND UNDERSTAND ALL FILL STATION INSTRUCTIONS.
WARNING: Compressed air will rush out of the vent hole (part #4) when relieving
pressure from the fill hose. Use caution in directing the venting air.
ALWAYS WEAR GLOVES AND SAFETY GLASSES WHEN OPERATING THIS
FILL STATION!!
WARNING: Do NOT disconnect the hose under pressure. Disconnecting the hose
under pressure could cause damage to the hose fitting and personal injury to the
operator.

www.Ninjapaintball.com
2
SETTING UP THE NINJA DIN 300 PCP FILL
STATION
The Ninja DIN 300 connects high pressure air bulk cylinders or N2 bulk
cylinders to a Pre-charged Pneumatic (PCP) airgun.
On the backside of the fill station is a vent port.
▲FOR SAFETY REASONS, THE FILL PORT MUST BE DIRECTED
AWAY FROM THE OPERATOR AND BYSTANDERS.
Do not over tighten the vent knob as this may damage the
seal. Only turn the knob enough to stop the release of gas.
▲Never operate the PCP Fill Adapter unless a PCP AIR RIFLE is
attached to the fill adapter on the end of the fill hose. Operating
the PCP Fill Adapter without a PCP AIR RIFLE attached will
cause the fill hose to “whip”. Injury may result!!
1.0 OPERATION with a HIGH PRESSURE BULK AIR CYLINDER OR N2
THIS FILL ADAPTER WILL VENT GASES STORED UNDER HIGH
PRESSURE MAKE CERTAIN THE VALVE VENT KNOB (part #2) IS
CLOSED (turned fully clockwise) BEFORE CONNECTING TO A HIGH
PRESSURE BULK AIR CYLINDER.

www.Ninjapaintball.com
3
1.1 Screw the Din 300 in to the high pressure cylinder valve (Fig. 1) making certain all components
are clean and dry. Tighten securely by hand only. Do NOT use tools to tighten.
1.2 Connect the Din 300 with quick disconnect socket to the fill fitting on the PCP airgun (Fig. 2).
Close the vent on the Din 300 fill station to prevent leaks. Ensure the air rifle you are filling has a
1/8 male Industrial Interchange quick disconnect, see figure 1.4a. Pull the sleeve/collar back on
the quick disconnect #6 and Connect the fill station female quick disconnect socket (part #6) to
the fill nipple on your PCP air gun. THE SLEEVE /COLLAR MUST SNAP FORWARD AND
BE SECURE! Do not force it on and if it does not fit properly do not fill. See figure 1.4c.
1.3 MAKE SURE CONNECTION IS SECURE.
1.4 Open the bulk cylinder valve slowly. You should hear the airgun filling with air. A complete fill
should take no more than approximately 5 seconds. View the gauge on the gun to prevent over
filling the gun reservoir and causing valve lock.
1.5 Check the airgun pressure gauge for complete fill per the air gun manufacturers recommendation.
Upon completion of filling, close the valve on the bulk cylinder. Open the vent on the Din 300 fill
adapter to relieve pressure. Then disconnect the quick disconnect from the gun. If you are finished
with the bulk cylinder remove the Din 300 fill adapter by turning counter-clockwise direction.
NOTE: Keep the adaptor clean and dry. Periodically inspect the hose for any show of wear.
WARNING: Do NOT disconnect the hose under pressure. Disconnecting the
hose under pressure could cause damage to the hose fitting and personal
injury to the operator.

www.Ninjapaintball.com
4
3.0Maintenance and Care of the Ninja Din 300 PCP Fill Station
Keep the Fill Adapter clean and dry.
Periodically check the female quick disconnect (#4 in parts picture) for ball damage and for
o-ring wear. Check the DIN300 fitting o-ring for wear, replace all damaged parts prior to
use. Check the fill hose for thread integrity, cracks or other wear and replace any suspect
part immediately call 877-646-5287 www.ninjapaintball.com