Niviuk QUBIK 19 User manual
QUBIK
User’s manual
2
NIVIUK GLIDERS & AIR GAMES SL C/ DEL TER 6, NAVE D 17165 LA CELLERA DE TER - GIRONA - SPAIN
TEL. +34 972 42 28 78 FAX +34 972 42 00 86
[email protected] www.niviuk.com
QUBIK
EXPERIENCE EVERY JOURNEY
WELCOME
We wish to welcome you to our team and thank you for your condence in
our glider product line.
We would like to share the enthusiasm with which we created this wing
and the importance and care we took in the design and manufacture of
this new model in order to offer maximum pleasure on every ight with a
Niviuk glider.
It’s time to go further in the world of paramotoring. The Qubik offers
excellent performance with a wide speed-range. A stable and safe
progression wing ideal for those ights you’ve always dreamt of, but not
yet dared to attempt. Start your engine and prepare to experience new
thrills.
We are condent you will enjoy ying the QUBIK and will soon discover the
meaning of our motto:
“The importance of small details”.
This is the user manual and we recommend you read it carefully.
The Niviuk Team.
USER MANUAL
This manual provides you with the necessary information on the main
characteristics of your new paraglider.
Whilst it provides information on the wing, it cannot be viewed as an
instructional handbook and does not offer the training required to y
this type of paraglider. Training can only be undertaken at a certied
paragliding school and each country has its own system of licensing.
Only the aeronautical authorities of respective countries can determine
pilot competence.
The information in this manual is provided in order to warn you against
adverse ying situations and potential dangers.
Equally, we would like to remind you that it is important to carefully read all
the contents of your new QUBIK manual.
Misuse of this equipment could lead to severe injuries or death. The
manufacturers and dealers cannot be held responsible for misuse of the
paraglider. It is the responsibility of the pilot to ensure the equipment is
used correctly.
3
SUMMARY
WELCOME 2
USER MANUAL 2
1. CHARACTERISTICS 4
1.1 WHO IS IT DESIGNED FOR? 4
1.2 CERTIFICATION 4
1.3 IN-FLIGHT BEHAVIOUR 4
1.4 CONSTRUCTION, MATERIALS 5
1.5 ELEMENTS, COMPONENTS 6
2. UNPACKING AND ASSEMBLY 7
2.1 CHOOSING THE RIGHT LOCATION 7
2.2 PROCEDURE 7
2.3 CONNECTING THE HARNESS 7
2.4 HARNESS TYPE 7
2.5 SPEED-BAR 8
2.6 INSPECTION AND WING
INFLATION ON THE GROUND 9
2.7 ADJUSTING THE BRAKES 10
3. THE FIRST FLIGHT 10
3.1 CHOOSING THE RIGHT LOCATION 10
3.2 PREPARATION 10
3.3 FLIGHT PLAN 10
3.4 PRE-FLIGHT CHECK 10
3.5 WING INFLATION, CONTROL
AND TAKE-OFF 11
3.6 LANDING 11
3.7 PACKING 11
4. IN FLIGHT 12
4.1 DOUBLE STEERING SYSTEM 12
4.2 FLYING IN TURBULENCE 13
4.3 POSSIBLE CONFIGURATIONS 13
4.4 ACCELERATED FLIGHT 15
4.5 FLYING WITHOUT BRAKE LINES 15
4.6 LINE KNOT(S) IN FLIGHT 15
5. LOSING ALTITUDE 15
5.1 BIG EARS 15
5.2 B3 TECHNIQUE 16
5.3 B-LINE STALL 17
5.4 SPIRAL DIVE 17
5.5 SLOW DESCENT TECHNIQUE 17
6. SPECIAL METHODS 18
6.1 ACROBATIC FLIGHT 18
7. CARE AND MAINTENANCE 18
7.1 MAINTENANCE 18
7.2 STORAGE 18
7.3 PACKING INSTRUCTIONS 19
7.4 CHECKS AND INSPECTION 19
7.4 REPAIRS 19
8. SAFETY AND RESPONSIBILITY 20
9. GUARANTEE 20
10. ANNEXES 21
10.1 TECHNICAL DATA 21
10.2 MATERIALS DESCRIPTION 22
10.3 RISERS PLAN 23
10.4 LINE PLAN 24
10.5 DIMENSIONS QUBIK 19 25
10.6 DIMENSIONS QUBIK 21 25
10.7 DIMENSIONS QUBIK 23 26
10.8 DIMENSIONS QUBIK 25 26
10.9 DIMENSIONS QUBIK 27 27
10.10 CERTIFICATION 28
4
1. CHARACTERISTICS
1.1 WHO IS IT DESIGNED FOR?
The QUBIK was designed for paramotor ights. Aimed at experienced
and independent pilots who enjoy powered ight, whether they are
undertaking long cross-country or short local ights. With the QUBIK
they have a fast and high performing wing without sacricing strength,
solidity and safety typical of Niviuk wings. Pilots will also benet from the
latest advances and technologies of our sport.
1.2 CERTIFICATION
Air Turquoise thoroughly tested the structural strength of QUBIK and
certies its compliance with all DGAC stipulations. The test procedure
was dened in accordance with the methodology of the EN 926-1:2015
and LTF NFL II-91/09 chapter 3 standards.
The shock test proved that the wing can resist 1200 daN of force.
The load test passed the requirement to withstand the 5.25 G of its
maximum take off load for 3 seconds. 228 kg.
Only the aeronautical authorities of respective countries can determine
pilot competence
For further information on the ight test and the corresponding
certication number, please see the nal pages of this manual or see
niviuk.com.
1.3 IN-FLIGHT BEHAVIOUR
The NIVIUK Team has carried out extensive and meticulous design work
on the QUBIK. After several prototypes and many hours of test ying,
numerous adjustments were made. These prototypes were then tested in
all types of ight conditions. This intense development work supported
by the combined experience of the whole team has resulted in a wing
with unbeatable ight behaviour.
This intense development work was underpinned by the combined
experience of the whole team and has resulted in a wing with incredible
ight behaviour.
Thanks to the leading edge reinforcements and the SLE (Structured
Leading Edge), the wing distinguishes itself with light handling, precise
response, manoeuvrability, safety and high stability. With these
characteristics, it is perfect for powered ight.
Its ination behaviour is the rst step to appreciating its obedient
character. Its lightness, both in terms of weight and handling, has
a positive impact on all its ying attributes, allowing you to y with
complete freedom.
The addition of SLE technology with its light weight and structured cells
ensures that every ination and take off remains simple and uneventful.
Thanks to the QUBIK’s controlled and progressive ination rate the pilot
remains in complete control of the wing throughout all stages of the take
off. This allows extra time to position the wing in the perfect pre-launch
position directly above the head.
The running phase is perhaps one of the most critical when taking off
with a powered wing, so any technological assistance is an advantage
to take off easily and safely. During take off in order to create sufcient
lift traditional proles demand high forward speed, in other words, a long
and fast run. The new technological features on the QUBIK facilitate
early lift off and therefore reducing the amount of time and physical effort
5
required when running.
Once airborne, the QUBIK wing impresses with precision in response,
handling, safety, a sporty look and good performance. These are
achieved thanks to the same SLE technology that brought us so many
successes in high-level competitions and which we have now perfectly
adapted to this paramotor wing.
It will very quickly become apparent to the pilot that the handling and
manoeuvrability of the QUBIK remains light and efcient during all
aspects of ight and even in the most adverse conditions every pilot
input is met with an immediate and precise response.
When the trimmers are opened the wing’s prole changes and
accelerates, penetrating without any problems. The brakes are usable in
all the trimmer positions, even accelerated.
The performance of this new wing is substantially above average for
this type of glider.. The power required of the engine is in the low to
medium range. Its consumption is much less than most wings due to the
effectiveness of a glider perfectly designed to ensure the top stability and
performance in all aspects of ight.
The QUBIK has the same advantages when landing as it does on take-
off. With a low speed approach, a short nal glide and with the pilot
always in total control the QUBIK can land in the smallest of areas with
precision and ease.
It is worthwhile remembering that the best paraglider in the hands of
a bad pilot does not guarantee a happy ending. The QUBIK’s passive
safety measures should also be complemented by the passive safety
offered by the pilot’s other ying equipment, i.e. the harness, helmet, the
emergency parachute etc. The extraordinary smooth behaviour of the
QUBIK and common sense piloting will give you many hours of peaceful
ying.
1.4 CONSTRUCTION, MATERIALS
The QUBIK has all the technological innovations used on other Niviuk
gliders and is built with the most careful selection of current materials. It
has all the current technology and accessories available to improve pilot
comfort whilst increasing safety and performance.
In the design of all Niviuk products the team aims to ensure development
and continuous improvement. The technologies developed in recent
years have allowed us to develop greater, better wings. It is in this
context that we would like to introduce the technologies included in this
new model.
RAM Air Intake - this system is characterised by the arrangement of the
air inlets, to ensure optimal maintenance of internal pressure. Thanks to
this design, we were able to reduce their size, while maintaining the same
air ow at all angles to improve laminar ow. More consistency across
the whole speed range and better performance without compromising on
safety.
Titanium Technology (TNT) - a revolutionary technique using titanium.
Using Nitinol in the internal construction provides a more uniform prole
and reduces the weight to gain efciency in ight. Nitinol provides the
highest level of protection against deformation, heat or breaks. The
leading edge is more rigid and the wing surface remains perfectly taut,
without creases or parasitic drag. This optimises glide in all phases of
the ight. Because the exible rods always return to their original shape,
the integrity of the prole is never affected. Nitinol provides the highest
level of protection against deformation, heat or breaks.
Structured Leading Edge (SLE) - the use of the SLE considerably
reduces the amount of Mylar which was used in previous Niviuk wings
and this also reduces the weight of the leading edge. Therefore it is
easier to inate this wing than a paraglider without this system.
6
3D Pattern Cut Optimisation (3DP) – the latest generation of wings
require a new fabric panel pattern and cutting system. Creating separate
panels for each of the sections at the front of the wing means the sail
fabric is more taut and crease-free. During the cutting, the optimal
orientation of the fabric section is selected, depending on its nal
location. If the fabric pattern is properly aligned with the axes of load, it
suffers less deformation after repeated use, to the long-term benet of
the leading edge.
3D Leading Edge (3DL) - adding an extra seam to the longitudinal
axis of the glider helps, on the one hand, give more consistency and
volume to the prole (a more efcient 3D contour) and on the other, joins
and shapes the leading edge panels. The fabric is guided by the panel
position to ensure fewer creases and better load distribution. The result
is a cleaner prole, which benets the wing in terms of performance and
durability.
3DL - adding an extra reinforced seam to the leading edge helps to
ensure more consistency and volume in the prole. This provides a more
efcient 3D contour.
Reex System Prole (RSP) - with the RSP the engine does not need
much power to achieve greater thrust, resulting in less consumption,
more autonomy, less need for power, better durability, mechanical
efciency and increased performance.
The use of these technologies is a big technological leap forward in
building wings and a big improvement in ight comfort.
For the construction process of the QUBIK we use the same criteria,
quality controls and manufacturing processes as in the rest of our range.
From Olivier Nef’s computer to fabric cutting, the operation does not
allow for even a millimetre of error. The cutting of each wing component
is performed by a rigorous, extremely meticulous, automated computer
laser-cutting robotic arm.
This program also paints the guideline markers and numbers on each
individual fabric piece, thus avoiding errors during this delicate process.
The jigsaw puzzle assembly is made easier using this method and
optimises the operation while making the quality control more efcient.
All Niviuk gliders go through an extremely thorough and detailed nal
inspection. The canopy is cut and assembled under strict quality control
conditions facilitated by the automation of this process.
Every wing is individually checked with a nal visual inspection.
The fabric used to manufacture the glider is light, resistant and durable.
The fabric will not experience fading and is covered by our warranty.
All lines are made from Technora with a polyester sheath.
The line diameter has been calculated depending on the workload and
aims to achieve the required best performance with the least drag. The
sheath protects the line cores from UV rays and abrasions.
The lines are semi-automatically cut to length and all the sewing is
completed under the supervision of our specialists.
Every line is checked and measured once the nal assembly is
concluded.
Each glider is packed following specic maintenance instructions as
recommended by the fabric manufacturer.
Niviuk gliders are made of premium materials that meet the requirements
of performance, durability and certication that the current market
demands.
Information about the various materials used to manufacture the wing
can be viewed in the nal pages of this manual.
1.5 ELEMENTS/COMPONENTS
The QUBIK is delivered with a series of accessories that will greatly assist
you in the maintenance of your paraglider:
- A Koli bag This bag is large enough to hold all equipment comfortably
7
and with plenty of space.
- An inner bag to protect the wing during storage and transport.
- An adjustable compression strap to compress the inner bag and reduce
its volume.
- A repair kit with self-adhesive Ripstop tape in the same colour as the
wing and spare parts to protect the maillons.
2 UNPACKING AND ASSEMBLY
2.1 CHOOSING THE RIGHT LOCATION
We recommend unpacking and assembling the wing on a training hill or
a at clear area without too much wind and free of obstacles. It will help
you to carry out all the recommended steps required to check and inate
the QUBIK.
We recommend the whole installation procedure is supervised by a
qualied professional instructor or ofcial dealer. Only they can address
any doubts in a safe and professional way.
2.2 PROCEDURE
Take the QUBIK out of the rucksack, open and unfold it on the ground
with the lines positioned on the undersurface, oriented in the direction
of ination. Check the cloth and lines are undamaged and all maillons
connecting the lines and risers are locked. Identify, and if necessary
untangle, the A, B, C and the brake lines and corresponding risers. Make
sure that there are no knots.
2.3 ASSEMBLY WITH THE ENGINE
After carefully laying out the wing connect the risers to the harness/
engine according to the paramotor manufacturer instructions and set the
trimmers to the neutral position.
Check the engine manufacturer’s specication on attachment points.
The QUBIK risers are colour-coded.
- Right: green
- Left: red
This colour-coding makes it easier to connect the wing to the correct
side and helps prevent pre-ight errors.
Correctly connect the risers to attachment points so that the risers and
lines are correctly ordered and free of twists.
Check that the carabiners are properly fastened and securely locked.
2.4 HARNESS TYPE
Check the engine manufacturer’s specication on attachment points.
Before any ight commences it is strongly recommended that the pilot
checks the connection of the wing to the harness/engine and whilst
seated in the harness checks the length of the brake lines, that they can
easily reach the handles and also easily reach and operate the trimmers
on both sides. The QUBIK is tted with two brake height options so the
pilot can choose their optimal the brake position.
2.5 SPEED-BAR
The speed-bar is a means of temporary acceleration by changing the
ow over the prole. The speed system comes pre-installed on the risers
and is not modiable as it conforms to the measurements and limits
stipulated in its certication.
The QUBIK includes a speed system with with a differential between the
A-D risers of 16 cm.
The speed system is engaged when the pilot pushes the speed-bar - not
included as standard with this glider model - with their feet (see 2.5.1
Speed system assembly)
8
The speed system uses an action/reaction system. Released, the speed-
bar is set to neutral. When the bar is pushed using the feet, the wing
accelerates. The speed can be regulated by varying the pressure on the
bar. Once the pressure on the bar is released, the speed system returns
to the neutral setting.
The speed system is efcient, sensitive and precise. The pilot can use the
system whenever they want during the ight. In the neutral position the
glider will y at the standard speed and glide. Using full speed-bar, the
wing will y at maximum speed, but the glide will be adversely affected.
•Released speed-bar: the A, B, C and D-risers are aligned.
•Full speed-bar: the difference between the A – D risers becomes:
16 cm in all sizes
Please note!
The use of the speed system results in changes to the speed and
reactions of the wing. For more information, please see the certication
report.
2.5.1. Speed system assembly
The speed-bar consists of the bar that the pilot pushes with their feet, as
well as the two cords that connect it to the speed system components
on the risers. Once you have chosen the type of speed-bar you prefer,
you must install it. Some considerations:
• You should use the type of speed-bar you consider appropriate,
depending on the type of harness, personal preferences, etc.
• The speed-bar is detachable to facilitate its connection and/or
disconnection to the risers as well as subsequent adjustment.
• To connect it to the harness, please follow the instructions of the
harness manufacturer. The majority of harnesses have a speed system
pre-installed.
• The standard connection of the speed-bar to the speed system is via
Brummel hooks, where two slots in the hooks are interlocked, making
their connection / disconnection easy. However, any connection system
that is safe may be used.
2.5.2. Changing the riser cords
In spite of the speed system having pulleys with bearings to reduce
friction to a minimum, the frequency with which the speed-bar is used
causes the cord to wear and you may need to replace them.
In all Niviuk gliders the speed system cords on the risers are completely
removable and easily replaceable. You can use the Brummel hooks, not
use them, remove them, use another type of connector, etc. It is even
possible to x the speed-bar cords directly to the speed system on
the risers. This last option makes the connection / disconnection more
laborious, but means the cord has maximum travel without obstructions
or restrictions which is very useful for some models of harnesses.
2.6 TRIMMERS
Using the trimmers:
The trimmers are an adjustable prole modication system. They are
activated by releasing trimmers. To open the trimmers, press the trim
tab inwards until the tape is released. Release the tape until it is in the
desired position. When the trim tab is no longer pressed, the tape
is locked in that position. Colloquially this is known as “releasing” or
“opening” the trimmers.
Once it is locked in that position, it will not release automatically and
return to its initial position. The pilot is solely responsible for opening and
closing the trimmers.
To close the trimmers, pull the tape down using the handle - without
touching the trimmer tabs. Release the handle when you reach the
required position. Colloquially this is called “closing” the trimmers.
The trimmers must be applied symmetrically.
9
•Trimmers closed or in the neutral position: The A, B, C, D risers are
aligned.
•Trimmers fully open: the difference between the A - C-risers becomes:
24.5 cm in all sizes
Take off
Thanks to the prole of the QUBIK, all aspects of take off can be
controlled using the trimmers.
The SLE system optimally positions the cells openings of the leading
edge and thus assuring the rapid formation of the wing prole. This
contribution is in itself already a huge advantage when attempting to
take off in nil wind conditions, but the correct use of the trimmers at
this time will further facilitate an easy take-off. In nil wind and without
the application of trimmers the QUBIK inates easily and effortlessly.
However, by adjusting the trimmers we can control both the ination and
the speed at which the wing rises. We should not confuse the speed of
the ination with the speed of the forward run required. It is important to
remember that the minimum take-off speed is achieved with the trimmers
closed and as the trimmers are opened more speed will be required.
Therefore every pilot should be aware of the trimmer settings and make
any necessary adjustments appropriate to the conditions, the terrain and
pilot skill.
In ight
The trimmers on the QUBIK are highly and precisely adjustable, allowing
the pilot to either increase speed by opening the trimmers or conversely
decrease speed by closing them. Each trimmer is equipped with a clearly
numbered scale to allow the pilot to easily check and conrm the exact
setting of each. Each trimmer may be set to compensate for the torque
effect of the engine, allowing ne tuning to ensure the wing remains
in symmetrical ight. The pilot will very quickly become familiar with
the scale and after just a few ights be able to optimise every ight by
adjusting the trimmers to their most efcient setting.
With the trimmers closed and using just the full range of brake travel the
QUBIK is a precise, light to handle and a fun machine to y.
Landing
The QUBIK offers the comfort of ending the ight with the perfect
landing; large areas and long runs are no longer required.
Please note that in wind nil conditions the forward ground speed
encountered may be signicantly higher and during landing that speed
must be decreased as safely as possible. This can be achieved by
fully closing the trimmers and proportionately applying the brakes. If
necessary, as the pilot reaches the ground a longer run off should also
be carried out. When landing in moderate wind conditions, the ground
speed is reduced so a simple and progressive application of the brakes
will be enough for a perfect landing.
Landing with open or half open trimmers is possible, but it will be
necessary to balance the application of the brakes to the position of the
trimmers and the forward ground speed being experienced. Of course,
open trimmers and an increase in forward ground speed when landing
may require a larger landing area as opposed to when the trimmers are
closed. The QUBIK very efciently transforms forward speed into lift and
inherently allows a wide margin for error either with or without wind.
2.7 INSPECTION AND WING INFLATION ON THE GROUND
After your gear has been thoroughly checked and the weather conditions
deemed favourable for ying, inate your QUBIK as many times as
necessary to familiarise yourself with its behaviour. Inating the QUBIK
is easy and should not require a great deal of physical effort. Inate the
wing with a little pressure from the body using the harness. This may be
assisted by using the A-lines. Do not pull on them; just accompany the
natural rising movement of the wing. Once the wing is inated to the
overhead position, appropriate control with the brakes will be sufcient to
hold it there.
10
2.8 ADJUSTING THE BRAKES
The length of the main brake lines are adjusted at the factory and
conform to the length stipulated during certication. However, they
can be changed to suit your ying style. It is advisable to y with the
original setting for a period of time to get used to the actual behaviour
of the QUBIK. In case it is necessary to modify the brake length, loosen
the knot, slide the line through the brake handle to the desired point and
re-tighten the knot rmly.
Only qualied personnel should carry out this adjustment. You must
ensure that the modication does not affect the trailing edge and
slow the glider down without pilot input. Both brake lines should be
symmetrical and the same length. We recommend using a clove hitch or
bowline knot.
When changing the brake length, it is necessary to check that they do
not engage when the speed-bar is used. When we accelerate, the glider
rotates over the D-riser and the trailing edge elevates.
It is important to check that the brake is adjusted to take into
consideration this extra distance during acceleration. With this prole
deformation there is a risk of generating turbulence and causing a frontal
or asymmetric collapse.
2.9 ADJUSTING THE BRAKE PULLEY
Depending on the position of the pilot during the ight or the height of
the trike hang points, the QUBIK has the possibility of moving the brake
pulleys to a variety of positions to ensure pilot comfort.
The pulley is fastened to the riser loop that can be adjusted easily.
The riser has 2 possible xing points (distributed along the entire riser) to
accommodate the pulley.
3. THE FIRST FLIGHT
3.1 CHOOSING THE RIGHT LOCATION
For the rst ight we recommend going to your usual ying area and that
a qualied instructor is present and supervising the entire procedure.
3.2 PREPARATION
Repeat the procedures detailed in section 2 UNPACKING AND
ASSEMBLY to prepare your equipment.
3.3 FLIGHT PLAN
Planning a ight before taking off to avoid possible problems later is
always a good idea.
3.4 PRE-FLIGHT CHECK
Once ready, but before taking off, conduct another equipment inspection.
Conduct a thorough visual check of your gear with the wing fully open,
the lines untangled and properly laid out on the ground to ensure that all
is in working order. Be certain the weather conditions are suited to your
ying skill level.
3.5 WING INFLATION, CONTROL AND TAKEOFF
Whether taking off on foot or using a trike, the QUBIK does not require
a different technique. The control of the QUBIK is intuitive and the wing
inates easily and progressively in a controlled manner. Any unwanted
oscillation or required course correction can easily be controlled with
gentle pilot input.
When the decision has been made to take off, only a short run is required
and the QUBIK will quickly transform the forward speed and thrust of
the engine into lift. Even with a trike, only a very short rolling distance
11
is required to achieve the desired forward speed of 25 km/h and take
off. The QUBIK has been designed to easily and efciently inate whilst
providing exceptional directional stability without pitching or hanging
back behind the pilot. Excessive amounts of energy are not required
when taking off with the QUBIK, simply set the trimmers to the correct
positions (see 2.6)
3.6 LANDING
The QUBIK offers the comfort of ending the ight with the perfect
landing; large areas and long runs are no longer required.
Please note that in wind nil conditions the forward ground speed
encountered may be signicantly higher and during landing that speed
must be decreased as safely as possible. This can be achieved by
fully closing the trimmers and proportionately applying the brakes. If
necessary, as the pilot reaches the ground a longer run off should also
be carried out. When landing in moderate wind conditions, the ground
speed is reduced so a simple and progressive application of the brakes
will be enough for a perfect landing.
Landing with open or half open trimmers is possible, but it will be
necessary to balance the application of the brakes to the position of the
trimmers and the forward ground speed being experienced. Of course,
open trimmers and an increase in forward ground speed when landing
may require a larger landing area as opposed to when the trimmers are
closed. The QUBIK very efciently transforms forward speed into lift and
inherently allows a wide margin for error either with or without wind.
3.7 PACKING
The QUBIK has a complex leading edge, manufactured using a variety
of different materials and it must be packed carefully. A correct folding
method is very important to extend the useful life of your paraglider.
It should be concertina-packed, with the leading edge reinforcements at
and the exible rods stacked one on top of the other. This method will
keep the prole in its original shape and protect the integrity of the wing
over time. Make sure the reinforcements are not bent or folded. It should
not be folded too tightly to avoid damage to the cloth and/or lines.
At Niviuk we have designed the NKare Bag, a bag designed to assist you
with rapid packing which helps maintain the integrity of the leading edge
and its internal structures in perfect condition.
The NKare Bag guides you through the folding process, allowing you to
concertina pack the wing with each rod on top of the other and then fold
the wing as required. This folding system ensures that both the fabric and
the reinforcements of the internal structure are kept in perfect condition.
4. IN FLIGHT
It is important to point out that the appropriate response to each adverse
manoeuvre can vary from size to size; even within the same size at
maximum or minimum load the behaviour and reactions of the wing may
vary.
The performance and speed of the QUBIK depend directly on the engine
power and wing-loading.
With the RSP (Reex System Prole) the engine does not need much
power to achieve greater thrust, resulting in less consumption, more
autonomy, less need for power, better durability, mechanical efciency
and increased performance.
However, in order to get the maximum power out of this wing, we will
need an engine that is able to push a highly loaded wing. Without the
right wing-loading and without the required power, the wing will not
operate to its full potential.
DOUBLE STEERING SYSTEM
Double Steering System
The QUBIK has two brake lines: the main brake (conventional brake) and
the High Speed Tip (xed to a separate handle on the B-riser). The High
Speed Tip gives the pilot the ability to turn without pulling the brakes,
thus avoiding deforming the prole and therefore preventing a decrease
in performance and speed.
High Speed Tip
The High Speed Tip on the QUBIK consists of a line attached to the
wingtip. It enables the pilot to correct the direction easily and accurately
without using the main brake controls and therefore, the performance of
the wing is not affected.
Torque Compensator
The High Speed Tip is a very efcient tool to compensate for the natural
equal and opposite effect caused by engine inertia or torque. This line
can be adjusted or set according to the needs of the pilot.
To become familiar with the manoeuvres described below, we
recommend practising within the auspices of a licensed training outt.
4.1 FLYING IN TURBULENCE
The QUBIK has an excellent prole to deal with incidents; it is very
stable in all conditions and has a high degree of passive safety, even in
turbulent conditions. All paragliders must be piloted for the prevailing
conditions and the pilot is the ultimate safety factor.
We recommend active ying in turbulent conditions, always taking
measures to maintain control of the wing, preventing it from collapsing
and restoring the speed required by the wing after each correction.
Do not correct the glider (braking) for too long in case this provokes a
stall. If you have to take corrective action, make the input then re-
establish the correct ying speed.
4.2 POSSIBLE CONFIGURATIONS
To become familiar with the manoeuvres described below, we
recommend practising within the environment of a licensed training outt.
You must adapt your use of the brakes depending on the wing-loading
and avoid over-steering.
It is important to note that the type of reaction to a manoeuvre can vary
from one size of wing to another, and even within the same size the
behaviour and reactions may be different depending on the wing-loading.
In the test report, you will nd all the necessary information on how to
handle your new wing during each of the tested manoeuvres. Having this
information is crucial to know how to react during these manoeuvres in
real ight, so you can deal with these situations as safely as possible.
Asymmetric collapse
In spite of the QUBIK’s prole stability, strong turbulent air may cause
the wing to collapse asymmetrically in very strong turbulence, especially
if you do not y actively and prevent the collapse. In this case the glider
conveys a loss of pressure through the brake lines and the harness.
To prevent the collapse from happening, pull the brake handle on the
affected side of the wing. It will increase the incidence of the wing
(angle of attack). If the collapse does happen, the QUBIK will not react
violently, the turning tendency is gradual and easily controlled. Weight-
shift toward the open, ying side (the opposite side of the collapse) to
keep the wing ying straight, while applying light brake pressure to that
side if necessary. Normally, the collapsed side of the wing should then
recover and reopen by itself. If it does not, then pull the brake handle on
the collapsed side decisively and quickly all the way (100%) down. You
may have to repeat this pumping action to provoke the re-opening of the
deated glider side. Do not over-brake or slow down the ying side of the
wing (control the turn). Once the collapsed side is open make sure you
return to normal ying speed.
Frontal collapse
Due to the QUBIK’s design, in normal ying conditions frontal collapses
are unlikely to take place. The wing’s prole has great buffering abilities
when dealing with extreme incidence changes. A frontal collapse
may occur in strong turbulent conditions, entering or exiting powerful
thermals. Frontal collapses usually re-inate without the glider turning,
but a symmetrically applied quick braking action with a quick deep pump
of both brakes will accelerate the re-ination if necessary. Release the
brake lines immediately to return to default glider air speed.
Negative spin
A negative spin does not conform to the QUBIK’s normal ight behaviour.
Certain circumstances however, may provoke a negative spin (such as
trying to turn when ying at very low air speed whilst applying a lot of
brake). It is not easy to give any specic recommendation about this
situation other than quickly restoring the wing’s default air speed and
angle of attack by progressively reducing the tension on the brake lines.
The normal wing reaction will be to have a lateral surge on the re-
accelerated side with a rotation not greater than 360º before returning to
default air speed and a straight ight path trajectory.
Parachutal stall
The possibility of entering or remaining in a parachutal stall have been
eliminated from the QUBIK. A parachutal stall is virtually impossible with
this wing. If it did enter into a parachutal stall, the wing loses forward
motion, becomes unstable and there is a lack of pressure on the brake
lines, although the canopy appears to be fully inated. To regain normal
air speed, release brake line tension symmetrically and manually push on
the A-lines or weight-shift your body to any side WITHOUT PULLING ON
THE BRAKE LINES.
Deep Stall
The possibility of the QUBIK stalling during normal ight is very unlikely.
It could only happen if you are ying at a very low air speed, whilst over-
steering or performing dangerous manoeuvres in turbulent air.
To provoke a deep stall, the wing has to be slowed down to its minimum
air speed by symmetrically pulling the brake lines all the way (100%)
down until the stall point is reached and held there. The glider will rst
pitch rearward and then reposition itself overhead, rocking slightly,
depending on how the manoeuvre is done.
When entering a stall, remain clear-headed and ease off the brake lines
until reaching the half-way point of the total brake travel. The wing will
then surge violently forward and could reach a point below you. It is most
important to maintain brake pressure until the glider has returned to its
default overhead ying position.
To resume normal ight conditions, progressively and symmetrically
14
release the brake line tension to regain air speed. When the wing reaches
the overhead position, the brakes must be fully released. The wing will
then surge forward to regain full air speed. Do not brake excessively at
this moment as the wing needs to accelerate to pull away from the stall
conguration. If you have to control a possible frontal collapse, briey
pull both brake handles down to bring the wing back up and release
them immediately while the glider is still in transition to reposition itself
overhead.
Cravat
A cravat may happen after an asymmetric collapse, when the end
of the wing is trapped between the lines. Depending on the nature
of the tangle, this situation could rapidly cause the wing to spin. The
corrective manoeuvres to use are the same as those applied in case of
an asymmetric collapse: control the turn/spin by applying tension on
the opposite brake and weight shift opposite to the turn. Then locate
the 3STI stabilo line (attached to the wing tip) trapped between the
other lines. This line has a different colour and is located on the outside
position of the B-riser.
Pull this line until it is taut. This action will help to release the cravat. If
ineffective, y down to the nearest possible landing spot, controlling the
direction with both weight-shift and the use of the brake opposite to the
tangled side. Be cautious when attempting to undo a tangle while ying
near terrain or other paragliders; it may not be possible to continue on
the intended ight path.
Over-controlling
Most ying problems are caused by wrong pilot input, which then
escalates into a cascade of unwanted and unpredicted incidents. We
should note that the wrong inputs can lead to loss of control of the glider.
The QUBIK was designed to recover by itself in most cases. Do not try
to over-correct it!
Generally speaking, the reactions of the wing, which are caused by too
much input, are due to the length of time the pilot continues to over–
control the wing. You have to allow the glider to re-establish normal ying
speed and attitude after any type of incident.
4.3 ACCELERATED FLIGHT
The QUBIK’s prole was designed for stable ight throughout its entire
speed range. The speed-bar can be used in strong winds or signicant
sink.
When accelerating the wing, the prole becomes more sensitive to
turbulence and closer to a possible frontal collapse. If a loss in internal
wing pressure is felt, tension on the speed-bar should be reduced to a
minimum and a slight pull on the brake lines is recommended to increase
the wing’s incidence angle. Remember to re-establish the air speed after
correcting the angle of attack.
It is NOT recommended to accelerate near obstacles or in very turbulent
conditions. If necessary, constantly adjust the movements and pressure
on the speed-bar whilst doing the same to the brake lines. This balance
is considered to be ‘active piloting’.
4.4 FLYING WITHOUT BRAKE LINES
If, for any reason at all, the QUBIK’s brake lines become disabled in ight,
it will become necessary to pilot the wing with the C-risers and weight
shifting until landing. The C-lines steer easily because they are not under
much tension, however you will need to be careful and not handle them
too heavily in case this causes a stall or negative spin. The wing must
be own at full speed during the landing approach, and the C-risers will
have to be pulled symmetrically all the way down shortly before contact
with the ground. This braking method is not as effective as using the
brake lines, and hence the wing will land with a higher ground speed.
15
4.5 LINE KNOT(S) IN FLIGHT
The best way to avoid knots and tangles is to thoroughly inspect the lines
as part of a systematic pre-ight check. If a knot is spotted during the
take off phase, immediately abort the launch sequence and stop.
If inadvertently taking off with a knotted line, the glider drift will need to
be compensated by weight-shifting to the opposite side and applying a
slight brake pull to that side. Gently pull the brake line to see if the knot
can be undone or try to locate the problem line. Try pulling it to see if the
knot can be undone. Beware of trying to clear a knotted line or untangle
a line in ight when close to the terrain. If the knot is too tight and cannot
be undone, carefully and safely y to the nearest landing zone. Be
careful: do not pull too hard on the brake handles because there will be
an increased risk of stalling the wing or entering a negative spin. Before
attempting to clear a knot, make sure there are no other pilots ying in
the vicinity.
5. LOSING ALTITUDE
Knowledge of different descent techniques could become vital in
certain situations. The most suitable descent method will depend on the
particular situation.
To become familiar with the manoeuvres described below, we
recommend practising within the environment of a licensed training outt.
5.1 BIG EARS
Big ears is a moderate descent technique, able to increase the sink rate
to –3 or –4 m/s and reduces the ground speed by 3 to 5 km/h. The angle
of attack and effective wing-loading will also increase due to the smaller
surface area of the wing.
Standard technique
To perform the ‘Big ears’ manoeuvre, take the outermost line on each
A-riser and simultaneously, smoothly pull them outward and downward.
The wingtips will fold in.
To re-establish forward speed and the correct angle of attack, accelerate
once the ears are pulled.
Keep the ears pulled in until you have lost the desired altitude.
Let go of the lines to re-inate the tips automatically. If they do not, try
progressively pulling one brake then the other. We recommend inating
the wing tips asymmetrically, without major change to the angle of
attack, especially when ying near the ground or ying in turbulence.
Beware of the risk of stalling!
The action of reaching for the outermost A-lines to make ears, can
inadvertently mean pulling the brakes. The same can happen when we
are holding the tips down with the outermost A-lines, it is possible to
accidentally affect the brakes. This can obviously lead to a signicant
speed decrease.
In paragliders with a very pronounced arc, pulling big ears means an
increase in drag. On a very arched wing, the ears do not fold, they just
hang. The increase of drag is more pronounced than on wings with a less
pronounced arc.
The QUBIK is designed with little chord, which is good in normal ight
conditions. However, this same damping is what can cause us to have
problems to regain normal ying speed after a high increase of the angle
of attack and the added drag of the ears. These particularities, together
with turbulent thermic conditions, could cause an unintentional stall.
The solution: big ears may still be applied but you must be fully aware
of the above-mentioned points and act accordingly. To avoid the stall,
simply use half speed-bar (this is sufcient) to increase the speed and
decrease the angle of incidence. This should allow you to maintain
16
sufcient speed to prevent the stall. Take care not to pull the brakes while
making the ears as this will make a stall more likely!
5.2 B3 TECHNIQUE
On the new generation paragliders the application of big ears can create
a high degree of trailing edge turbulence. In addition, with the length of
the chord and the arc of the wing, the ears have a tendency to “ap”,
increasing the turbulence and causing the QUBIK to lose too much
airspeed, making it necessary for the pilot to recover it, either using the
the speed-bar or by releasing the ears.
This new rapid descent technique was rst discovered by our Niviuk
team pilots in 2009 while ying a competition prototype wing, which,
because of its line plan and high aspect ratio would not allow big ears to
be applied. In fact, big ears on 2-liner wings can often prove difcult.
With the current 2 or 3-liner wings, the inability to pull big ears, or the risk
involved in doing so, concerns many pilots who want to have a controlled
rapid descent technique. For the above reasons we recommend using
the ‘3B3’ line.
This technique easily increases the descent rate without causing
problems and without the risk of causing a collapse while maintaining
high speed.
How? Locate the 3B3 line on your risers and, as you would when
applying big ears, simply pull down rmly and smoothly until you see
both wingtips drop back slightly. The forward speed of the glider speed
will then reduce slightly, quickly stabilise and then increase. You will then
experience a descent rate of around 5-6 m/s.
We recommend the application of the speed-bar whilst using this
technique. Controlled turning of the wing can easily be maintained by
weight shifting, exactly the same as you would with big ears. During this
manoeuvre, the rst sensation is a decrease in relative wind and a slight
backwards inclination of the wing, as if going backwards.
To exit the manoeuvre release the lines as you would with big ears,
control the pitch and the wing will quickly adopt normal ight. This new
technique allows a comfortable and controllable rapid descent without
the risk of experiencing a cravat. It is very comfortable and makes turning
simple. We advise you to rst try this technique in smooth conditions
with sufcient altitude above appropriate terrain.
This is a new controlled descent technique that only needs a little
practise to be executed with total comfort and effectiveness.
5.3 B-LINE STALL
When carrying out this manoeuvre, the wing stops ying, loses all
horizontal speed and the pilot is no longer in control of the paraglider.
The airow over the prole is interrupted and the wing enters a situation
similar to parachuting.
To enter this manoeuvre, the B-risers are gripped below the maillons and
symmetrically pulled down together (approx. 20-30 cm) and maintained
in that position.
Initiating the maneuver is physically demanding because it can take
some strength to pull the risers down until the wing is deformed. After
this, the physical effort is less. Continue to hold the risers in position.
Once the wing is deformed, its horizontal speed will drop to 0 km/h;
vertical descending speed increases to –6 to –8 m/s, depending on the
conditions and how the manoeuvre is performed.
To exit the manoeuvre, simultaneously release both risers. The wing will
then slightly surge forward and automatically return to normal ight. It is
better to let go of the lines quickly rather than slowly.
This is an easy descent technique to perform, but remember that
the wing will stop ying, will lose all forward horizontal speed, and
its reactions will change markedly when compared to a normal ight
conguration.
5.4 SPIRAL DIVE
17
This is a more effective way to rapidly lose altitude. Beware that the wing
will experience and be subjected to a tremendous amount of descending
and rotating speed (g-force), which can cause a loss of orientation and
consciousness (blackout). This manoeuvre must therefore be done
gradually to increase one’s capacity to resist the g-force exerted on
the body. With practise, you will fully appreciate and understand it.
Only practise this manoeuvre at high altitude and with enough ground
clearance.
To start the manoeuvre, rst weight shift and pull the brake handle
located on the inner side of the turn. The intensity of the turn can be
controlled by braking slightly using the outer brake handle.
A paraglider ying at its maximum rotating speed can reach –20 m/s, or
the equivalent of a 70 km/h vertical descent, and will stabilise in a spiral
dive from 15m/s onwards.
Good enough reasons to familiarise yourself with the manoeuvre and
understand how to exit it.
To exit this manoeuvre, the inner brake handle (down side of the turn)
must progressively be relaxed while momentarily applying tension to the
outer brake handle opposite to the turn. The pilot must also weight shift
and lean towards the opposite side of the turn at the same time.
The exit should be performed gradually and smoothly so that the
changes in pressure and speed can be noted.
When exiting the spiral, the glider will briey experience an asymmetrical
acceleration and dive, depending on how the manoeuvre was carried out.
Practise these manoeuvres at sufcient altitude and with moderation.
6. SPECIAL METHODS
6.1 TOWING
The QUBIK does not experience any problem whilst being towed. Only
qualied winch personnel should handle the certied equipment to carry
out this operation. The wing must be inated similarly as during a normal
take off.
It is important to use the brakes to correct the ight path alignment,
especially if the glider begins to turn. Since the wing is subject to a slow
airspeed and with a high positive angle of attack, we must make any
corrections with a high degree of feel and delicacy, in order to avoid a
stall.
6.2 ACROBATIC FLIGHT
Although the QUBIK was tested by expert acrobatic pilots in extreme
situations, it was not designed for it. We do not recommend using this
glider for acrobatic ying!!!
We consider acrobatic ights to be any form of piloting different than
standard ights. Learning acrobatic manoeuvres should be conducted
under the supervision of qualied instructors within a school environment
and over water with all safety/rescue elements in place. Centrifugal
forces as high as 4 to 5 g can be exerted on the body and wing during
extreme manoeuvres.
7. CARE AND MAINTENANCE
7.1 MAINTENANCE
Niviuk we are rmly committed to make technology accessible to all
pilots. Therefore our wings are equipped with the latest technological
advances gained from the experience of our R&D team.
Careful maintenance of your equipment will ensure continued top
18
performance. Apart from the general checks, we recommend actively
maintaining your equipment.
A pre-ight check is obligatory before each ight.
If there is any damage to the equipment or you suspect any areas of
the wing are susceptible to wear, you should inspect these and act
accordingly.
All incidents involving the leading edge should be reviewed. A hard
impact of the leading edge against a hard surface can damage the sail
cloth.
Unsheathed lines provide increased performance, but this means more
care should be taken when using and maintaining the wing.
Thanks to TNT, the wing has more safety and performance, but
this means being more careful with the material. If any Nitinol rod is
damaged, they are easily replaceable.
The fabric and the lines do not need to be washed. If they become
dirty, clean them with a soft damp cloth, using only water. Do not use
detergents or other chemicals.
If your wing is wet from contact with water, place it in a dry area, air it
and keep it away from direct sunlight.
Direct sunlight may damage the wing’s materials and cause premature
aging. After landing, do not leave the wing exposed to the sun. Pack it
properly and stow it away in its backpack.
If your wing is wet from contact with salt water, immerse it in fresh water
and dry it away from direct sunlight.
7.2 STORAGE
It is important for the wing to be correctly folded when stored. Keep it in
the in a cool, dry place away from solvents, fuels, oils.
Do not leave your gear inside a car boot, as cars left in the sun can
become very hot. A rucksack can reach temperatures up to 60ºC.
Weight should not be laid on top of the equipment.
It is very important to pack the wing correctly before storage.
It is essential that the wing is properly folded and packed. In case
of long-term storage it is advisable, if possible, that the wing is not
compressed and it should be stored loosely without direct contact with
the ground. Humidity and heating can have an adverse effect on the
equipment.
7.3 PACKING INSTRUCTIONS
It is very important to pack the wing correctly before storage.
In case of long-term storage it is advisable, if possible, that the wing is
not compressed and it should be stored loosely without direct contact
with the ground. Humidity and heating can have an adverse effect on the
equipment.
The QUBIK has a complex leading edge, manufactured using a variety
of different materials and it must be packed carefully. A correct folding
method is very important to extend the useful life of your paraglider. It
should be concertina-packed, with the leading edge reinforcements at
and the exible rods stacked one on top of the other. This method will
keep the prole in its original shape and protect the integrity of the wing
over time. Make sure the reinforcements are not bent or folded. It should
not be folded too tightly to avoid damage to the cloth and/or lines.
19
The QUBIK comes with the KOLI BAG as standard. This bag allows rapid
packing and transportation without problems.
At Niviuk we have designed the NKare Bag, a bag designed to assist you
with rapid packing which helps maintain the integrity of the leading edge
and its internal structures in perfect condition.
The NKare Bag guides you through the folding process, allowing you
to concertina pack the wing with each rod on top of the other and
thus protecting the SLE and then fold the wing in the correct position,
depending on the lengths of the SLE. This folding system ensures that
both the fabric and the reinforcements of the internal structure are kept in
perfect condition.
7.4 CHECKS AND INSPECTIONS
Inspections
The QUBIK must be periodically serviced. An inspection must be
scheduled every 100 ying hours or every two years whichever comes
rst (EN/LTF norm).
We strongly recommend that any repairs should be done in a specialist
repair shop by qualied personnel. This will guarantee the airworthiness
and continued certication of your QUBIK.
A thorough pre-ight check must be performed before every ight.
7.5 REPAIRS
In the case of small tears, you can temporarily repair these by using the
Ripstop tape included in the repair kit, as long as no stitching is required
to mend the fabric.
Any other tears or repairs should be done in a specialist repair shop by
qualied personnel.
Damaged lines must be repaired or exchanged immediately.
Please refer to the line plan at the end of this manual.
Any repair should be done in a specialist repair shop by qualied
personnel.
Niviuk can not be held responsible for any damage caused by incorrect
repairs.
8. SAFETY AND RESPONSIBILITY
It is well known that free-ying with a paramotor or trike is considered a
high-risk sport, where safety depends on the person who is practicing it.
Incorrect use of this equipment may cause severe, life-changing injuries
to the pilot, or even death.
Manufacturers and dealers cannot be held responsible for your
decisions, actions or accidents that may result from participating in this
sport.
You must not use this equipment if you have not been properly trained
to use it. Do not take advice or accept any informal training from anyone
who is not properly qualied as a ight instructor
9. GARANTEE
The equipment and components are covered by a 2-year warranty
against any manufacturing defect.
The warranty does not cover misuse of the equipment.
DISCLAIMER: Paragliding is an activity that requires concentration,
specic knowledge and common sense. Take care! You should learn
to paraglide under the auspices of a certied ying school. Take out
personal insurance and make sure you have all the correct licences. Be
modest when you evaluate your skill level in terms of meteorology.
Niviuk’s liability for damages covers only its own products.
Niviuk can take no responsibility for your actions. When ying, accept the
risk involved.
This manual suits for next models
4
Table of contents
Other Niviuk Windsurfing Equipment manuals
