No Butts Bin SR1563-F User manual

Assembly Instructions
Shelter type: SR1563-F
SR1563-F-02-100119-USA

EXPLODED VIEW
13
12
11
9
10
5
7
6
14
8
3
1
2
4
12
11
2
ITEM
NO. PART NAME
DRG NUMBER LENGTH
Default/QT
Y.
1 S1C Frame S1C
Default
9
2 CB1 Bracket CB1
Default
8
3 JF1 Bracket JF1
Default
12
4 ST3 Roof Tie ST3
Default
1
5 P1 Post P1
Default
1
6 FT1 Bracket FT1
Default
3
7 FT3 Bracket FT3
Default
8
8 RB1 Bracket RB1
Default
16
9 R2 Rafter R2
Default
5
10 Sealing Strip - 2195mm Sealing Strip
Default
8
11 ACE2 Roof Panel
Default
2
12 ACC2 Roof Panel
Default
2
13 RC2 Roof Strip
Default
5
14 A2 Angle A2
Default
8
15 40x40 End cap BOUGHT IN ITEM
40 x 40 x 20
13

3
PARTS LIST
ITEM NO.
PART NO.
DESCRIPTION
DIMENSION
(MM)
DIMENSION
(INCHES)
IMAGE QTY.
1
S1C
Frame 2000 x 1035 78.74 x 40.55 9
2
CB1
Bracket 110 x 110 4.33 x 4.33 8
3
JF1
Bracket 220 x 40 8.66 x 1.58 12
4
ST3
Roof Tie
2060 x 40 x
40
81.10 x 1.57 x
1.57 1
5
P1
Post 2000 x 1030 40.55 x 78.74 1
6
FT1
Foot Bracket
109 x 100 x
40
4.29 x 3.93 x
1.57 3
7
FT3
Foot Bracket
109 x 100 x
80
4.29 x 3.93 x
3.27 8
8
RB1
Bracket 110 x 46 4.33 x 1.81 16
9
R2
Rafter
2200 x 40 x
40
87.40 x 40.55 5
10
SS
Sealing Strip Trim To 2195 Trim To 86.61 4 ROLLS
11
ACE2
Roof Panel 2210 x 1050 87 x 41.34 2
12
ACC2
Roof Panel 2210 x 1030 87 x 40.55 2
13
RC2
Roof Strip 2200 87.40 5
14
A2
Roof Edge
Angle
40.55 x 1.97
x 1.97
Trim To Fit 8
15
EC40
Plastic End
Cap
40 x 40 1.57 x 1.57 24

4
Fittings/Tools
Tools required:
Drill/Screwdriver
Mallet
Hack saw
Spanner
Torx bit
Bolt set M10
Nut Washer
Black
Cap
T25 AB1210
M10 x 60 mm
25 mm
Tech
screw
M10/12 x 100mm
Concrete Bolt
Pack C+D
40 40 80 80 202 13
Required 21 21 42 42 161 11
Image

4180
2110
83.07
164.57
JF1
CB1
S1C
CB1CB1CB1
Ensure correct alignment on
corners.
Step 1
Assemble S1C frames to make up the main structure using CB1 brackets
for the corners and JF1 brackets for the straight joints.
5
MEASUREMENTS IN BLUE - MM
MEASUREMENTS IN GREEN - INCHES

FT3
FT1
ST3
CB1
JF1
P1
P1
A
CB1
ST3
DETAIL A
SCALE 1 : 5
JF1 INSIDE
CB1 UNDERNEATH
Step 2
Attach P1 post using one JF1 bracket, then attach ST3 tie bar using
another JF1 bracket and two CB1 brackets.
Move the shelter to its final position, make sure the structure is square
and attach the FT1 and FT3 foot brackets to secure the shelter to the
ground.
NOTE: Attach EC40 to P1
and ST3 before installing.

R2
RB1
R2
RB1
40.75 40.75 40.75 40.75
1035 1035 1035 1035
FRONT VIEW
Step 3
Use RB1 brackets to secure the R2 roof rafters.
7

ACC2
ACE2
ACC2
RC2
ACE2
PCC2
SS
RC2
SS
PCE2
PCC2
PCE2
Step 4
Apply sealing strips (SS) to the top of the rafters. Align ACE2 roof panels
with the outer rafters then space out the ACC2 panels evenly.
Cover the two edges along the outer rafters and gaps with RC2 strips
before screwing them into place using the 25mm TEC screws .
8

A2 Angle
A2 Angle
Step 5
Fit the square end caps ( EC40 ) to any open ends of box sections.
Screw A2 roof angles onto the edges of the roof as shown below.
9

4078.50 FEET HOLE CENTERS
4180
1035 1035 1035 985.50
985.50 995 2048.50
1035 985.50
1035 1035
2180.33
40.75 40.75
80.65
39.17
38.80
40.75 38.80
40.75 40.75 40.75 38.80
161.04
85.84
164.57
10
Plan view
Suggested size for concrete base: 200mm / 7.87in oversized on all four sides.

11
NOTES:

12
MAINTENANCE:
To ensure your products give you many years of use we recommend that you:
THANK YOU
FOR PURCHASING THIS PRODUCT
Clean panels regularly with soapy water •
Ensure all fittings are tight (for example after a big storm) •
Touch up any exposed metal should it get scratched •
CONTACT DETAILS:
Email : [email protected]
Web : www.nobutts.com
Tel : [phone]
No Butts Bin Company, Inc. 16 Birch Lane, Madison, CT 06443
All Parts and Fixings checked by:
Print Name: Signature: